BISE Gujranwala · Punjab Class 9
BISE Gujranwala Annual 2025 Class 9 Physics (Objective, Group I) (5471)
Set by BISE Gujranwala for Punjab Class 9 Physics, Annual 2025: 15 minutes and 12 marks, on Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science. The paper itself is on BISE Gujranwala’s website; this page adds what it covers, how to use it and original practice questions on the same topics.
Paper facts
- Series
- Annual 2025
- Paper
- Objective, Group I
- Set by
- BISE Gujranwala
- Code
- 5471
- Tier
- Not tiered
- Time
- 15 minutes
- Marks
- 12
- Calculator
- Not recorded here: check the paper’s instructions
- Syllabus
- Old Punjab syllabus (PCTB Physics 9 used until the 2024-25 session), not the NC 2023 book. Some questions, such as satellites and heat transfer, are not in the new course.
- Links checked
- 17 November 2026
Official files
- Question paper(opens BISE Gujranwala’s website)
- Mark schemenot public
- Examiner reportnot public
These files belong to BISE Gujranwala. Labverse links to them and never hosts or copies them. Labverse is not affiliated with BISE Gujranwala.
What this paper covers
8 topic groups from our map of Punjab Board Class 9 Physics. Revise each one with its topic pages and simulations before you sit the paper.
- Physical quantities and measurements
Physical quantities and SI units · Prefixes and scientific notation · Vernier callipers · Micrometer screw gauge · Measuring mass and time · Measuring cylinders and displacement cans · Errors and uncertainty in measurements · Significant figures · Precision and accuracy
Significant figures, prefixes and units trainerVernier caliperMicrometer screw gaugeMeasuring density
- Kinematics
Scalars and vectors · Types of motion · Distance and displacement · Speed and velocity · Acceleration · Distance–time graphs · Speed–time graphs · Equations of motion · Free fall acceleration
Adding and resolving vectorsDistance and displacementMotion graphsSUVAT equations of motion
- Dynamics
Contact and non-contact forces · Newton's law of gravitation · Fundamental forces · Free-body diagrams · Newton's first law · Newton's second law · Newton's third law · Mass, weight and balances · Friction · Terminal velocity · Momentum and impulse · Conservation of momentum
Free-body diagrams and resultant forceStatic and kinetic frictionOrbits and gravityWeight, mass and gravity
- Turning effects of force
Parallel forces and addition of forces · Torque (moment of force) and couple · Resolution of vectors · Principle of moments · Centre of mass and centre of gravity · Equilibrium and its conditions · States of equilibrium and stability · Circular motion and centripetal force
Adding and resolving vectorsPrinciple of momentsCentre of mass and stabilityFree-body diagrams and resultant force
- Work, energy and power
Work · Kinetic energy · Potential energy · Conservation of energy · Renewable and non-renewable energy sources · Power · Efficiency
Work doneEnergy skate trackEnergy stores and transfersEnergy resources
- Mechanical properties of matter
Elasticity and Hooke's law · Density · Pressure · Pressure in liquids · Atmospheric pressure · Barometers and manometers · Pascal's law and hydraulic systems
Hooke's law and springsMeasuring densityPressure in solidsLiquid pressure and depth
- Thermal properties of matter
Kinetic molecular theory of matter · Plasma: the fourth state of matter · Temperature, heat and internal energy · Liquid-in-glass and thermocouple thermometers · Temperature scales and conversions · Sensitivity, range and linearity
- Nature of science
Physics and its branches · Interdisciplinary research · Scientific method: hypothesis, theory and law · Science, technology and engineering
How to use this paper
- 1. Time it. Set 15 minutes for 12 marks: about 75 seconds a mark. At 8 minutes you should be roughly halfway through the marks; if you’re well behind, speed up on the short questions.
- 2. Sit it in one go. Open the question paper on BISE Gujranwala’s website (the link above) and work on paper, with no notes.
- 3. Mark it with the official scheme. The mark scheme isn’t public, so check answers with your teacher, and use the marking points on our questions below to practise marking.
- 4. Learn from the marks you lost. For every lost mark, note whether it was knowledge, method, reading the question or time.
- 5. Log mistakes by topic. Keep one line per topic group (Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science) and add a tally each time a mark goes there.
- 6. Revisit, then redo. Work through the weakest group’s topic pages and simulations, try the questions below, and come back to the paper in a week.
Practise the same topics
6 original exam-style questions on this paper’s topics, written in the style of Punjab board exams (not taken from the paper). Try each one before you reveal the answer.
1.Significant figures show how reliably a quantity has been measured.
From the topic: Significant figures
(a)What are significant figures?
2 marksShow the answerHide the answer
Answer: The digits in a measurement that are known reliably, together with the first doubtful (estimated) digit.
Marking points
- The digits that are known reliably (accurately)
- Plus the first doubtful (estimated) digit
(b)Give the number of significant figures shown by each reading: (i) 0.0405 m (ii) 7.20 s (iii) 1.080 × 10⁻² kg
3 marksShow the answerHide the answer
Answer: (i) 3 (ii) 3 (iii) 4
Marking points
- 0.0405 m: 3
- 7.20 s: 3
- 1.080 × 10⁻² kg: 4
(c)Which zeros in 0.00350 m are significant? Give a reason.
2 marksShow the answerHide the answer
Answer: Only the last zero. The zeros before the 3 only fix the decimal point, but a zero at the end of a decimal was measured.
Marking points
- Only the final zero (after the 5)
- Leading zeros only fix the decimal point; an end zero after the point counts
2.Two cars, P and Q, leave a toll plaza on the M-2 at the same moment and travel in the same direction. Their distance–time graphs are straight lines from the origin. P reaches 600 m at 30 s and Q reaches 600 m at 50 s.
From the topic: Distance–time graphs
(a)Which car has the steeper line on the graph?
1 markShow the answerHide the answer
Answer: Car P
Marking points
- Car P
(b)Calculate the speed of each car.
2 marksShow the answerHide the answer
Answer: P: 600 ÷ 30 = 20 m s⁻¹. Q: 600 ÷ 50 = 12 m s⁻¹.
Marking points
- P = 20 m s⁻¹
- Q = 12 m s⁻¹
(c)How far apart are the two cars at 30 s?
2 marksShow the answerHide the answer
Answer: At 30 s, Q has covered 12 × 30 = 360 m, so the gap is 600 − 360 = 240 m.
Marking points
- Distance of Q at 30 s = 360 m
- Separation = 240 m
3.Two lead spheres of masses 100 kg and 25 kg are placed with their centres 0.50 m apart. Take G = 6.67 × 10⁻¹¹ N m² kg⁻².
From the topic: Newton's law of gravitation
(a)Calculate the gravitational force between the spheres.
3 marksShow the answerHide the answer
Answer: F = Gm₁m₂/r² = 6.67 × 10⁻¹¹ × 100 × 25 ÷ (0.50)² = 6.67 × 10⁻¹¹ × 2500 ÷ 0.25 = 6.67 × 10⁻⁷ N
Marking points
- F = Gm₁m₂/r² with the values substituted
- r² = 0.25 m² (product of masses 2500 kg²)
- 6.67 × 10⁻⁷ N
(b)The spheres are moved until their centres are 1.0 m apart. Find the new force without using the full formula again.
2 marksShow the answerHide the answer
Answer: The distance is doubled, so the force becomes one-fourth: 6.67 × 10⁻⁷ ÷ 4 = 1.67 × 10⁻⁷ N.
Marking points
- distance doubled, so force becomes one-fourth (inverse-square law)
- 1.67 × 10⁻⁷ N
4.Wheels and ball bearings are used to make machines and vehicles easier to move.
From the topic: Friction
(a)Explain why rolling friction is less than sliding friction.
2 marksShow the answerHide the answer
Answer: The part of a rolling wheel in contact with the surface does not slide over it (no relative motion at the contact), and the area of contact is very small.
Marking points
- No sliding / relative motion at the point of contact
- Very small area of contact
(b)Describe a simple experiment, using a heavy book, a rubber band and some round pencils, to compare rolling and sliding friction.
3 marksShow the answerHide the answer
Answer: Pull the book across a table with the rubber band and note the stretch of the band. Place the book on the round pencils and pull it again. The band stretches much less, so a smaller force is needed: rolling friction is less than sliding friction.
Marking points
- Pull the book directly on the table and note the stretch of the band
- Repeat with the book resting on round pencils
- Less stretch on the pencils, so rolling friction is smaller
5.A uniform plank 3.0 m long has a mass of 20 kg. A 40 kg sack of wheat rests on it 0.60 m from end A. Take g = 10 N/kg.
From the topic: Centre of mass and centre of gravity
(a)Calculate the total weight of the plank and the sack.
2 marksShow the answerHide the answer
Answer: Plank: w = 20 × 10 = 200 N. Sack: w = 40 × 10 = 400 N. Total = 600 N.
Marking points
- Plank 200 N and sack 400 N
- Total weight 600 N
(b)Find the distance from A of the centre of gravity of the plank and sack together.
3 marksShow the answerHide the answer
Answer: The plank's weight acts at its midpoint, 1.5 m from A. Taking moments about A: 600 × x = 200 × 1.5 + 400 × 0.60 = 300 + 240 = 540, so x = 540 ÷ 600 = 0.90 m from A.
Marking points
- Plank's weight taken at its midpoint (1.5 m from A)
- 600 × x = 200 × 1.5 + 400 × 0.60 = 540
- x = 0.90 m from A
(c)A single support placed under this point holds the plank level. What upward force does the support provide?
1 markShow the answerHide the answer
Answer: 600 N, equal to the total weight.
Marking points
- 600 N
6.A loaded truck has a total mass of 12 000 kg. It rests on 10 tyres, and each tyre touches the road over an area of 300 cm². Use g = 10 m s⁻².
From the topic: Pressure
(a)Find the weight of the loaded truck.
1 markShow the answerHide the answer
Answer: w = mg = 12 000 kg × 10 m s⁻² = 1.2 × 10⁵ N.
Marking points
- 1.2 × 10⁵ N
(b)Find the total area of contact with the road in m².
2 marksShow the answerHide the answer
Answer: A = 10 × 300 cm² = 3000 cm². Dividing by 10 000 gives 0.30 m².
Marking points
- Total area = 3000 cm²
- 3000 ÷ 10 000 = 0.30 m²
(c)Calculate the pressure that the tyres exert on the road.
2 marksShow the answerHide the answer
Answer: P = F/A = 1.2 × 10⁵ N ÷ 0.30 m² = 4.0 × 10⁵ Pa.
Marking points
- P = F/A = 1.2 × 10⁵ ÷ 0.30
- 4.0 × 10⁵ Pa
(d)The truck is overloaded until its total mass is 15 000 kg. The contact area does not change. Find the new pressure on the road.
2 marksShow the answerHide the answer
Answer: The weight becomes 15 000 × 10 = 1.5 × 10⁵ N, so P = 1.5 × 10⁵ N ÷ 0.30 m² = 5.0 × 10⁵ Pa. For the same area, pressure rises in proportion to the force.
Marking points
- New weight = 1.5 × 10⁵ N
- P = 1.5 × 10⁵ ÷ 0.30 = 5.0 × 10⁵ Pa