Skip to content

Punjab Board Class 9 Physics · Physical quantities and measurements

Vernier callipers

Section 1.5

Vernier Callipers measure lengths up to about 15 cm with a least count of 0.1 mm (0.01 cm). Length = main scale reading + (Vernier scale reading × least count). A zero error is subtracted when the Vernier zero is on the right of the main-scale zero and added when it is on the left.

Loading simulation…

Symbols match your course. Open the full vernier caliper simulation for more presets and teacher tools.

What Vernier Callipers are for

A metre rule cannot tell whether a marble is 1.6 cm or 1.65 cm wide, because it only reads to the nearest millimetre. Vernier Callipers read ten times more finely, to 0.1 mm, for lengths up to about 15 cm: the outer diameter of a pipe, the inside width of a bottle neck or the depth of a small tin.

PartWhat it does
Main scaleFixed scale along the beam, marked in millimetres
Vernier scaleShort sliding scale: 10 equal divisions spread over 9 mm
Outside jawsGrip an object from outside, for an external diameter, width or thickness
Inside jawsOpen inside a hole or tube, for an internal diameter
Tail (depth gauge)Strip that slides out of the far end, for the depth of a hollow object

Least count

The least count (L.C.) is the smallest length an instrument can measure reliably. Each Vernier division is 9 mm ÷ 10 = 0.9 mm long, which is exactly 0.1 mm shorter than one main-scale division. So

L.C.=1 M.S. division−1 V.S. division=1 mm−0.9 mm=0.1 mm=0.01 cm\text{L.C.} = 1\ \text{M.S. division} - 1\ \text{V.S. division} = 1\ \text{mm} - 0.9\ \text{mm} = 0.1\ \text{mm} = 0.01\ \text{cm}

Sharing one main-scale division among all ten Vernier divisions gives the same value: 1 mm÷10=0.1 mm1\ \text{mm} \div 10 = 0.1\ \text{mm}.

Taking a reading

  1. Main scale reading (M.S.R.): find the Vernier zero and note the last main-scale mark it has passed.
  2. Vernier scale reading (V.S.R.): look along the Vernier scale for the one division that sits exactly in line with a main-scale mark. Its number is the V.S.R.
  3. Put them together:
Length=M.S.R.+(V.S.R.×L.C.)\text{Length} = \text{M.S.R.} + (\text{V.S.R.} \times \text{L.C.})

Because the least count is 0.01 cm, give every result to two decimal places in centimetres. If division 0 is in line, write 3.20 cm, not 3.2 cm.

Zero error and the corrected reading

Before measuring, close the jaws gently and compare the two zeros. If they coincide, there is no zero error. If not, every reading is wrong by the same amount, the zero error, and each observed reading must be corrected.

  • Vernier zero on the right of the main-scale zero. The instrument reads more than the true length. With division nn in line, zero error =n×L.C.= n \times \text{L.C.}, and you subtract it.
  • Vernier zero on the left of the main-scale zero. The instrument reads less than the true length. Count the divisions still missing: zero error =(10−n)×L.C.= (10 - n) \times \text{L.C.}, and you add it.

Worked numerical: a copper pipe and a marble

(a) With the jaws closed, the Vernier zero lies on the right of the main-scale zero and division 2 is in line. On a copper pipe the M.S.R. is 2.4 cm and division 7 is in line. Find the pipe's outer diameter.

Zero error=2×0.01 cm=0.02 cm(subtract)\text{Zero error} = 2 \times 0.01\ \text{cm} = 0.02\ \text{cm} \quad (\text{subtract}) Observed reading=2.4 cm+(7×0.01 cm)=2.47 cm\text{Observed reading} = 2.4\ \text{cm} + (7 \times 0.01\ \text{cm}) = 2.47\ \text{cm} Diameter=2.47 cm−0.02 cm=2.45 cm\text{Diameter} = 2.47\ \text{cm} - 0.02\ \text{cm} = 2.45\ \text{cm}

(b) A second instrument, closed, has its Vernier zero on the left of the main-scale zero with division 7 in line. On a glass marble it gives an M.S.R. of 1.5 cm with division 2 in line.

Zero error=(10−7)×0.01 cm=0.03 cm(add)\text{Zero error} = (10 - 7) \times 0.01\ \text{cm} = 0.03\ \text{cm} \quad (\text{add}) Diameter=1.5 cm+(2×0.01 cm)+0.03 cm=1.55 cm\text{Diameter} = 1.5\ \text{cm} + (2 \times 0.01\ \text{cm}) + 0.03\ \text{cm} = 1.55\ \text{cm}

Using the simulation

In the simulation above, the outside jaws are closed on a Brass cylinder. The Main scale reading card shows 2.3 cm, the Vernier scale reading (division in line) card shows 6, and the working line gives 2.3 cm + 6 × 0.01 cm = 2.36 cm. In the magnified view, division 6 glows where it meets a main-scale mark.

  1. Press the single › arrow (Open the jaws by 0.1 mm) a few times. Each press moves the glow one division along and adds 0.01 cm. Press Close to grip the cylinder again.
  2. Under Zero error, choose Right of 0. The Observed reading becomes 2.39 cm, the Zero error card shows 0.03 cm with "Vernier zero on the right: subtract", and the Corrected reading stays 2.36 cm. Choose Left of 0: the observed reading falls to 2.33 cm and the error is added.
  3. Pick Nothing (jaws empty) from In the jaws and press Close. With Left of 0 still chosen, division 7 is in line and the working shows (10 − 7) × 0.01 cm = 0.03 cm.
  4. Choose Steel washer (inside jaws) and press Open: the inside jaws spread until they touch the wall of the hole.
  5. Set Mode to Practice. Press Check zero, then Back, read both scales, type the true size and press Check.

Common mistakes

  • Taking the main scale reading from the mark beside the Vernier division that is in line. The main scale reading is the last main-scale mark before the Vernier zero.
  • Adding the Vernier scale reading as whole millimetres, such as 2.3 cm + 6 mm = 2.9 cm. Multiply it by the least count instead: 2.3 cm + 6 × 0.01 cm = 2.36 cm.
  • Correcting the zero error the wrong way. Vernier zero on the right of the main-scale zero: the reading is too big, so subtract. On the left: the reading is too small, so add.
  • For a zero on the left, using n × L.C. as the zero error. Count the divisions still missing: the error is (10 − n) × L.C.
  • Writing 3.2 cm when division 0 is in line. The instrument reads to 0.01 cm, so the reading is 3.20 cm.
  • Measuring without first closing the jaws to check for a zero error.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.Vernier Callipers are used in the laboratory to measure small lengths. The main scale is marked in millimetres, and 10 Vernier divisions cover 9 mm.

    1. (a)Define least count.

      1 mark
      Show the answer

      Answer: The least count is the smallest length that an instrument can measure reliably.

      Marking points

      • Smallest length the instrument can measure reliably
    2. (b)Show that the least count of these Vernier Callipers is 0.01 cm.

      2 marks
      Show the answer

      Answer: One Vernier division = 9 mm ÷ 10 = 0.9 mm. Least count = 1 M.S. division − 1 V.S. division = 1 mm − 0.9 mm = 0.1 mm = 0.01 cm.

      Marking points

      • 1 V.S. division = 9 mm ÷ 10 = 0.9 mm
      • L.C. = 1 mm − 0.9 mm = 0.1 mm = 0.01 cm
    3. (c)Name the part of the Vernier Callipers you would use to measure (i) the inside diameter of a steel cup, (ii) the depth of a hole drilled in a wooden block.

      2 marks
      Show the answer

      Answer: (i) The inside jaws. (ii) The tail (depth gauge).

      Marking points

      • Inside jaws
      • Tail / depth gauge
  2. 2.Before measuring a steel rod, a student closes the jaws of a pair of Vernier Callipers. The Vernier zero lies on the right of the main-scale zero, and the 4th Vernier division is in line with a main-scale mark. The least count is 0.01 cm.

    1. (a)Calculate the zero error and state whether it must be added to or subtracted from each reading.

      2 marks
      Show the answer

      Answer: Zero error = 4 × 0.01 cm = 0.04 cm. The Vernier zero is on the right, so the instrument reads too much and the zero error is subtracted.

      Marking points

      • 4 × 0.01 = 0.04 cm
      • Subtracted (Vernier zero on the right reads too much)
    2. (b)On the rod, the main scale reading is 3.1 cm and the 5th Vernier division is in line. Find the observed reading.

      2 marks
      Show the answer

      Answer: Observed reading = M.S.R. + (V.S.R. × L.C.) = 3.1 cm + (5 × 0.01 cm) = 3.15 cm.

      Marking points

      • 3.1 + 5 × 0.01
      • 3.15 cm
    3. (c)Find the true diameter of the rod.

      1 mark
      Show the answer

      Answer: True diameter = 3.15 cm − 0.04 cm = 3.11 cm.

      Marking points

      • 3.15 − 0.04 = 3.11 cm
  3. 3.A different pair of Vernier Callipers is closed. Its Vernier zero lies on the left of the main-scale zero, and the 6th Vernier division is in line with a main-scale mark. The least count is 0.01 cm.

    1. (a)Will this instrument give readings that are too large or too small? Give a reason.

      2 marks
      Show the answer

      Answer: Too small. The Vernier zero starts on the left of (behind) the main-scale zero, so every reading is less than the true length.

      Marking points

      • Too small
      • Vernier zero starts behind (left of) the main-scale zero
    2. (b)Calculate the zero error.

      2 marks
      Show the answer

      Answer: Zero error = (10 − 6) × 0.01 cm = 0.04 cm, which is added to each reading.

      Marking points

      • (10 − 6) × L.C.
      • 0.04 cm
    3. (c)The callipers are closed on a wooden scale. The main scale reading is 0.8 cm and the 3rd Vernier division is in line. Find the true thickness of the wooden scale.

      2 marks
      Show the answer

      Answer: Observed reading = 0.8 cm + (3 × 0.01 cm) = 0.83 cm. True thickness = 0.83 cm + 0.04 cm = 0.87 cm.

      Marking points

      • Observed reading 0.83 cm
      • 0.83 + 0.04 = 0.87 cm
  4. 4.Answer these short questions about Vernier Callipers.

    1. (a)A student records a reading as 4.6 cm when the zero division of the Vernier scale is in line with a main-scale mark. How should the reading be written? Give a reason.

      2 marks
      Show the answer

      Answer: It should be written as 4.60 cm, because the instrument measures to its least count of 0.01 cm, so the reading has two decimal places in centimetres.

      Marking points

      • 4.60 cm
      • Least count is 0.01 cm, so two decimal places
    2. (b)Why are Vernier Callipers better than a metre rule for measuring the diameter of a marble?

      1 mark
      Show the answer

      Answer: Their least count (0.1 mm) is ten times smaller than a metre rule's (1 mm), so the measurement is more precise.

      Marking points

      • Smaller least count (0.1 mm against 1 mm), so more precise

Quick check

6 questions

  1. 1.The least count of the Vernier Callipers used in school laboratories is:
  2. 2.The main scale reading is 5.2 cm and the 8th Vernier division is in line with a main-scale mark. The least count is 0.01 cm. The length is:
  3. 3.Which part of Vernier Callipers measures the depth of a hole drilled in a block?
  4. 4.With the jaws closed, the Vernier zero is on the right of the main-scale zero and the 5th Vernier division is in line (L.C. = 0.01 cm). An observed reading is 2.73 cm. The corrected reading is:
  5. 5.When the jaws are closed, the Vernier zero is on the left of the main-scale zero. The instrument:
  6. 6.Ten Vernier divisions cover 9 mm of the main scale. The length of one Vernier division is: