Skip to content

Matter and pressure simulation

Measuring Density Simulation

Work out density the way a school lab does. Measure blocks with rulers and a top-pan balance, find the volume of a pebble or key by displacement, weigh a liquid by difference, then drop objects into water, sea water or oil to test the floating rule.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A 2.0 cm cube of aluminium has a density of 2.7 g/cm³. A 4.0 cm cube is cut from the same block of aluminium. Its sides are twice as long. What density will you measure for the bigger cube?

Try this

  1. 1Start with the 2.0 cm aluminium cube. Read its side from the rulers, work out its volume, then press Weigh it and calculate the density before you look at the readout.
  2. 2Choose Cuboid and press Turn to bring its width against the ruler. Check that every ruler reading matches the sizes you set.
  3. 3Choose Irregular and press Lower in. Use the magnifier to read the bottom of the meniscus before and after. Then pick the Large stone: why does it need the other method?
  4. 4Choose Liquid and press Pour, noting both balance readings. Then press Empty, switch on Zero the balance with the empty cylinder on it, and pour again. Which readout changes, and which stays the same?
  5. 5Choose Float, drop the Pine block into Water, then try Sea water. Compare how much of it sits below the surface with the object's density ÷ the liquid's density.

Four experiments on one lab bench

Density tells you how much mass each cubic centimetre of a material carries, and you find it with two measurements: a mass and a volume. The mass always comes from the top-pan balance, which reads to 0.1 g. The volume is the tricky part, and each experiment in this simulation finds it differently. Switch between them with the buttons under the stage.

Blocks you can measure with a ruler

A cube, a cuboid or a cylinder has a formula for its volume, so rulers are all you need. The block stands in the corner made by two rulers, one lying along its front edge and one standing up at its end. Dashed lines run from its far edges to the scales so you can read each length to the nearest millimetre. A cuboid has three different sides, so turn it a quarter turn to bring its width to the ruler. Once you have the volume, move the block onto the balance and divide.

Try two cubes of the same metal with different sides. The bigger one has a far larger mass, yet the density hardly moves, because it depends on the material and not on the size of the sample.

Volume by displacement

A pebble, a key or a lump of plasticine has no neat formula. Hang it on a thread and lower it into a measuring cylinder: it shoves aside its own volume of water, and the level rises by exactly that much. Subtract the first reading from the second. The magnifier beside the cylinder shows the curved surface and an eye-level line, so you can practise reading the lowest point of the curve.

Some objects are too wide for the cylinder. For these, the can is filled until water just reaches its spout, then the object goes in and the overflow runs into a narrower cylinder. The water collected matches the volume of the object.

Watch out for two traps. If there is too little water, part of the object stays dry and the rise comes out too small. And a can that is not brimming at its spout keeps the first part of the displaced water, so the simulation tops it up before every new lowering.

The density of a liquid

The balance cannot hold a liquid without a container, so the cylinder is weighed empty and again with the liquid in it. The difference is the liquid's mass, and its volume is read from the scale. Zeroing the balance with the empty cylinder already on it does that subtraction for you.

Floating, sinking and average density

In the last experiment, objects are dropped into a beaker of water, sea water or cooking oil, shown in slow motion. A solid object floats when its density is lower than the liquid's. Once it settles, the share of its volume under the surface equals ρobject÷ρliquid\rho_\text{object} \div \rho_\text{liquid}, which you can check against the readout. A sealed steel ball floats because what counts is its average density: the mass of the steel and the air inside, divided by the whole volume it occupies.

The densities used are typical rounded values. Real wood, stone and plasticine vary from one sample to the next.

Equations

Check your understanding

7 questions

  1. 1.A block measures 4.0 cm × 2.5 cm × 2.0 cm and has a mass of 54 g. What is its density?
  2. 2.Water in a measuring cylinder reads 35 cm³. A brass key with a mass of 34 g is lowered in until it is covered, and the reading becomes 39 cm³. What is the density of the brass?
  3. 3.How should you read the volume of water in a measuring cylinder?
  4. 4.What is 7.9 g/cm³ in kg/m³?
  5. 5.An empty measuring cylinder reads 98.0 g on a balance. With 40 cm³ of a liquid in it, the balance reads 139.2 g. What is the liquid's density?
  6. 6.Which of these objects floats in fresh water?
  7. 7.A wooden block with a density of 0.60 g/cm³ floats in water of density 1.0 g/cm³. What fraction of its volume is below the surface?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more