Skip to content

SI Units and Prefixes: Base Units, Derived Units, Standard Form and Tricky Conversions

Learn the seven SI base units and how derived units such as the newton and joule are built from them, what each prefix from nano to giga means, how to write numbers in standard form, and how to convert areas, volumes, densities, speeds, energies and tiny times without slips.

Published · 6 min read

On this page

SI units are the international system of units that scientists everywhere use. Seven base units sit at its heart: the metre (m), the kilogram (kg), the second (s), the ampere (A), the kelvin (K), the mole (mol) and the candela (cd). Every other unit is a derived unit, made by multiplying or dividing base units. For example, speed is a distance divided by a time, so its unit is the metre per second, m/s.

A prefix in front of a unit multiplies it by a power of ten. The kilo in kilometre means 1000, so 1 km = 1000 m. The milli in millimetre means one thousandth, so 1 mm = 0.001 m.

Before you put numbers into a physics equation, change every value into base or derived SI units with no prefix. The one exception is the kilogram, which already has a prefix but is still the SI unit of mass.

What are the seven SI base units?

QuantityBase unitSymbol
Lengthmetrem
Masskilogramkg
Timeseconds
Electric currentampereA
TemperaturekelvinK
Amount of substancemolemol
Luminous intensity (brightness of a light source)candelacd

School physics uses the first five most. Temperatures are often given in °C. A temperature change has the same size in °C and in kelvin, so Δθ=15\Delta\theta = 15 °C is also a change of 15 K.

How are derived units built?

Write the equation that defines the quantity, then replace each quantity with its unit.

QuantityUnitBuilt from
Forcenewton, Nkg m/s², from F=maF = ma
Energy and workjoule, JN m, from W=FsW = Fs
Powerwatt, WJ/s, from P=E/tP = E/t
Pressurepascal, PaN/m², from p=F/Ap = F/A
Chargecoulomb, CA s, from Q=ItQ = It
Potential differencevolt, VJ/C, from E=QVE = QV
Resistanceohm, ΩV/A, from V=IRV = IR
Frequencyhertz, Hz1/s, cycles per second

Because a newton is kg m/s², a joule is N×m=kg m2/s2\text{N} \times \text{m} = \text{kg m}^2/\text{s}^2. Units named after people have a capital-letter symbol (N, W, Pa), but the full name starts with a small letter: newton, watt, pascal.

What do the prefixes mean?

PrefixSymbolMultiplies byExample
gigaG10910^9a 2.4 GHz Wi-Fi signal
megaM10610^6a 3 MW wind turbine
kilok10310^3a 5 km run
centic10−210^{-2}a 30 cm ruler
millim10−310^{-3}a 20 mA LED current
microµ10−610^{-6}a hair about 70 µm thick
nanon10−910^{-9}green light, about 530 nm

Capital and small letters matter: m is milli but M is mega, so 5 mW and 5 MW differ by a factor of a billion. Use one prefix at a time, and write the prefix straight onto the unit, as in mA or kJ. For mass, the prefix goes on the gram: a milligram is mg.

How do you write numbers in standard form?

Standard form writes a number as A×10nA \times 10^n, where 1≤A<101 \le A \lt 10 and n is a whole number, positive or negative.

  • The speed of light, 300 000 000 m/s, is 3.0×1083.0 \times 10^8 m/s.
  • A red blood cell, about 0.000 008 m across, is 8×10−68 \times 10^{-6} m, or 8 µm.
  • Green light, 530 nm, is 530×10−9=5.3×10−7530 \times 10^{-9} = 5.3 \times 10^{-7} m.

A prefix and a power of ten do the same job, so you can swap one for the other. On a calculator, the ×10ˣ or EXP key already includes the 10. Typing × 10 before pressing it makes the answer ten times too big.

Which unit conversions catch students out?

Worked example 1: cm³ to m³

A school measuring cylinder in Lagos holds 250 cm³ of water. Write this volume in m³.

Scale factor: 1 cm = 10−210^{-2} m, so 1 cm³ = (10−2)3=10−6(10^{-2})^3 = 10^{-6} m³

Working: 250×10−6=2.5×10−4250 \times 10^{-6} = 2.5 \times 10^{-4} m³

Answer: 2.5×10−42.5 \times 10^{-4} m³. A volume unit is cubed, so the factor is cubed too.

Worked example 2: mm² to m², for a drawing pin

The point of a drawing pin has an area of 0.10 mm². A thumb pushes on it with a force of 20 N. Find the pressure under the point.

Convert: 1 mm² = (10−3)2=10−6(10^{-3})^2 = 10^{-6} m², so 0.10 mm² = 1.0×10−71.0 \times 10^{-7} m²

Equation: p=FA=201.0×10−7p = \dfrac{F}{A} = \dfrac{20}{1.0 \times 10^{-7}}

Answer: p=2.0×108p = 2.0 \times 10^8 Pa. Leaving the area in mm² would give an answer a million times too small.

Worked example 3: g/cm³ to kg/m³

Brass has a density of 8.5 g/cm³. Write this in kg/m³.

Working: 1 g/cm3=10−3 kg10−6 m3=1000 kg/m31\ \text{g/cm}^3 = \dfrac{10^{-3}\ \text{kg}}{10^{-6}\ \text{m}^3} = 1000\ \text{kg/m}^3, so 8.5 g/cm³ = 8500 kg/m³

Answer: 8500 kg/m³

Worked example 4: km/h to m/s

An auto-rickshaw in Lahore travels at 36 km/h. Find its speed in m/s.

Working: 1 km/h = 1000 m in 3600 s, which is 13.6\dfrac{1}{3.6} m/s. So 36÷3.6=1036 \div 3.6 = 10 m/s

Answer: 10 m/s. To go back from m/s to km/h, multiply by 3.6.

Worked example 5: kJ and MJ

A 2.0 kW kettle in Birmingham runs for 3.0 minutes. Find the energy transferred in J, kJ and MJ.

Convert: P = 2000 W and t = 3.0 × 60 = 180 s

Equation: E=Pt=2000×180=360 000E = Pt = 2000 \times 180 = 360\,000 J

Answer: 3.6×1053.6 \times 10^5 J, which is 360 kJ or 0.36 MJ

Worked example 6: microseconds

A hospital scanner sends an ultrasound pulse into the body. The echo returns from an organ after 40 µs. Sound travels through soft tissue at about 1500 m/s. How deep is the organ?

Convert: 40 µs = 40×10−640 \times 10^{-6} s

There and back: distance = speed × time = 1500×40×10−6=0.0601500 \times 40 \times 10^{-6} = 0.060 m

Answer: the pulse went there and back, so the organ is 0.030 m, or 3.0 cm, deep.

Practise with real readings. The vernier callipers simulation can show lengths in cm or mm, so you can check each conversion. In the micrometer screw gauge simulation, measure the sheet of paper and write its thickness in metres in standard form. Once you have measured a sample in the density measurement simulation, the Working panel repeats the result in SI units: kilograms divided by cubic metres.

Common mistakes

  • Using 100 for areas and volumes. 1 m² is 10410^4 cm² and 1 m³ is 10610^6 cm³.
  • Mixing up m and M. Milli is a thousandth. Mega is a million.
  • Forgetting the grams. Change g to kg before using Ek=12mv2E_k = \tfrac{1}{2}mv^2 or W=mgW = mg.
  • Multiplying km/h by 3.6. To get m/s, divide by 3.6.
  • Leaving minutes or hours in. Power and energy equations need the time in seconds.
  • Writing 45 × 10³ as standard form. The first number must be from 1 to just under 10: 4.5×1044.5 \times 10^4.

Key points

  • The seven SI base units are the metre, kilogram, second, ampere, kelvin, mole and candela.
  • Derived units come from equations: N = kg m/s², J = N m, W = J/s, Pa = N/m².
  • Prefixes multiply by powers of ten: G 10910^9, M 10610^6, k 10310^3, c 10−210^{-2}, m 10−310^{-3}, µ 10−610^{-6}, n 10−910^{-9}.
  • Square or cube the conversion factor for areas or volumes.
  • Standard form is A×10nA \times 10^n with A from 1 up to, but not including, 10.
  • Convert every value to SI units before you use an equation.