Skip to content

Punjab Board Class 9 Physics · Turning effects of force

Torque (moment of force) and couple

Section 4.3

Torque, or moment of force, measures the turning effect of a force: τ = F × ℓ, where ℓ is the moment arm (perpendicular distance from the axis to the line of action). Its SI unit is N m. A couple is two equal, opposite, parallel forces acting at different points of a body.

Loading simulation…

Symbols match your course. Open the full principle of moments simulation for more presets and teacher tools.

Turning effect of a force

A force can do more than push a body along. When a body is fixed along one line, like a door on its hinges, a force can turn it instead. This is the turning effect of a force. Learn these terms:

  • Rigid body: a body in which the distance between any two of its points does not change when forces act on it.
  • Axis of rotation: the fixed line the body turns about. For a door it runs through the hinges.
  • Line of action: the line drawn through the point where a force acts, in the direction of the force.
  • Moment arm (ℓ\ell): the perpendicular distance from the axis of rotation to the line of action of the force.

Torque, or moment of force

The turning effect of a force is measured by its torque, which your textbook also calls the moment of force. Torque is the force multiplied by its moment arm:

τ=F×ℓ\tau = F \times \ell

With FF in newtons and ℓ\ell in metres, torque comes out in newton metres (N m), its SI unit. Punjab board papers give no formula sheet, so learn this with F=τ/ℓF = \tau / \ell and ℓ=τ/F\ell = \tau / F.

By the textbook's sign rule, a torque that would turn the body anticlockwise is positive and a clockwise one is negative.

Factors affecting torque

  1. The size of the force. Double the force at the same place and the torque doubles.
  2. The moment arm. The same force gives more torque further from the axis. That is why door handles sit on the edge away from the hinges, and why a village hand pump has a long handle.
  3. The direction of the force. If the line of action passes through the axis, then ℓ=0\ell = 0 and the torque is zero, however large the force.

When the force is not at right angles, let rr be the distance from the axis to the point where the force acts, and θ\theta the angle between rr and FF. The moment arm is ℓ=rsin⁡θ\ell = r\sin\theta, so

τ=rFsin⁡θ\tau = rF\sin\theta

The torque is greatest at θ=90∘\theta = 90^\circ and zero at θ=0∘\theta = 0^\circ. (Careful with the letters: one figure in the textbook names these two distances the other way round. Whatever the labels, the moment arm is always the perpendicular distance from the axis to the line of action of the force.)

Worked numerical 1: a wheel brace

A mechanic in a Gujranwala workshop pushes on a wheel brace with 120 N at right angles to the handle, 0.35 m from the centre of the nut. (a) Find the torque. (b) What force at 0.20 m gives the same torque? (c) Find the torque if the 120 N push at 0.35 m makes an angle of 30° with the handle.

Data: F=120 NF = 120\ \text{N}, ℓ=0.35 m\ell = 0.35\ \text{m}, τ=?\tau = ?

(a)τ=F×ℓ=120×0.35=42 N m\text{(a)}\quad \tau = F \times \ell = 120 \times 0.35 = 42\ \text{N m} (b)F=τℓ=420.20=210 N\text{(b)}\quad F = \frac{\tau}{\ell} = \frac{42}{0.20} = 210\ \text{N} (c)τ=rFsin⁡θ=0.35×120×0.5=21 N m\text{(c)}\quad \tau = rF\sin\theta = 0.35 \times 120 \times 0.5 = 21\ \text{N m}

Couple

Couple: two forces that are equal in size, opposite in direction and parallel, acting at two different points of the same body, so that their lines of action are not the same.

The two forces cancel, so a couple gives no resultant force and cannot move the body from place to place. But both forces turn the body the same way, so their torques add and the body rotates. You apply a couple when you turn a steering wheel with both hands, twist the cap off a water bottle or wind a clock key.

The textbook defines a couple but gives no formula for its torque, so this part goes a little beyond the book. To find the torque of a couple, take a point O between the forces, at distances r1r_1 and r2r_2 from their lines of action. Both torques have the same sense, so

τ=Fr1+Fr2=F(r1+r2)=F×d\tau = F r_1 + F r_2 = F(r_1 + r_2) = F \times d

where dd is the perpendicular distance between the two lines of action.

Worked numerical 2: a steering wheel

A van driver holds a steering wheel of diameter 0.36 m at opposite ends of a diameter. Each hand pushes along the rim with 25 N, in opposite directions. Find the torque of the couple.

τ=F×d=25×0.36=9 N m\tau = F \times d = 25 \times 0.36 = 9\ \text{N m}

Torque in the simulation

In the simulation above, each weight hangs straight down, so its moment arm is its distance from the pivot along the level rule. The simulation calls each torque a moment.

Weight A (3 N at the 30 cm mark) is already selected. Use the A: Position on the scale slider to move it to the 40 cm mark. Its row now reads 3 N × 0.10 m = 0.300 N m, half the torque it had before. At the 50 cm mark the readouts say it acts through the pivot, so it has no moment. Move it back to the 30 cm mark and raise the Weight slider to 6 N. The torque doubles to 1.20 N m.

In the simulation every force on the beam is a weight pulling straight down, so it cannot show a couple. To feel one, twist a bottle cap between finger and thumb.

Equations

  • Moment of a force

    Learn this

    τ=Fℓ

    moment of a force = force × perpendicular distance from the pivot

    Open calculator →

Common mistakes

  • Using the full distance to the point where the force acts when the force is slanting. Use the perpendicular distance, ℓ = r sin θ, or τ = rF sin θ.
  • Writing the unit of torque as N/m or N. Torque is force × distance, so its unit is N m.
  • Leaving the moment arm in centimetres and still writing the answer in N m. Convert cm to m first.
  • Thinking that any force on a body produces a torque. A force whose line of action passes through the axis has ℓ = 0 and gives zero torque.
  • Saying a couple pushes a body along. The two forces of a couple cancel, so the resultant force is zero; a couple only rotates the body.
  • Calling any pair of opposite forces a couple. The forces must be equal, parallel and opposite, and act along different lines.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.Doors, taps and spanners all rely on the turning effect of a force.

    1. (a)Define torque and write its SI unit.

      2 marks
      Show the answer

      Answer: Torque (moment of force) is the product of the force and its moment arm, τ = F × ℓ. Its SI unit is the newton metre (N m).

      Marking points

      • Torque = force × moment arm (perpendicular distance from the axis to the line of action)
      • Unit N m
    2. (b)Explain why a door handle is fixed far from the hinges.

      2 marks
      Show the answer

      Answer: Torque = force × moment arm. A handle far from the hinges has a large moment arm, so a small force produces enough torque to turn the door.

      Marking points

      • Large moment arm (distance from the axis/hinges)
      • Less force needed for the same torque
  2. 2.A cyclist presses down vertically on a pedal with a force of 400 N. The pedal crank is 0.17 m long.

    1. (a)Calculate the torque about the axle when the crank is horizontal.

      2 marks
      Show the answer

      Answer: The force is perpendicular to the crank, so ℓ = 0.17 m. τ = F × ℓ = 400 × 0.17 = 68 N m.

      Marking points

      • τ = F × ℓ = 400 × 0.17
      • 68 N m
    2. (b)The crank turns until it makes an angle of 30° with the vertical. Calculate the torque now.

      2 marks
      Show the answer

      Answer: The angle between the crank and the force is 30°. τ = rF sin θ = 0.17 × 400 × sin 30° = 0.17 × 400 × 0.5 = 34 N m.

      Marking points

      • τ = rF sin θ with θ = 30°
      • 34 N m
    3. (c)Explain why the torque is zero when the crank points straight down.

      1 mark
      Show the answer

      Answer: The line of action of the force passes through the axle, so the moment arm is zero.

      Marking points

      • Line of action passes through the axis, so ℓ = 0
  3. 3.A plumber turns the round handle of a valve using both hands. The hands are 0.24 m apart, on opposite sides of the centre, and each pushes with a force of 30 N at right angles to the line joining the hands, in opposite directions.

    1. (a)What is meant by a couple?

      2 marks
      Show the answer

      Answer: Two equal and opposite parallel forces acting at two different points of the same body (along different lines of action) form a couple.

      Marking points

      • Two equal, opposite, parallel forces
      • Acting at different points of the same body (different lines of action)
    2. (b)State the resultant force on the handle and explain why the handle still turns.

      2 marks
      Show the answer

      Answer: The resultant force is zero because the two forces are equal and opposite. Both forces turn the handle the same way, so their torques add and there is a net torque.

      Marking points

      • Resultant force is zero
      • The torques of both forces act in the same sense and add, so the handle rotates
    3. (c)Extension (beyond the textbook): calculate the torque of the couple.

      2 marks
      Show the answer

      Answer: τ = F × d = 30 × 0.24 = 7.2 N m.

      Marking points

      • τ = F × d (perpendicular distance between the forces)
      • 7.2 N m

Quick check

6 questions

  1. 1.The SI unit of torque is:
  2. 2.A force of 50 N acts at right angles to a spanner, 0.4 m from the centre of a nut. The torque is:
  3. 3.A force produces no torque about an axis when:
  4. 4.Two equal and opposite parallel forces act on a body along different lines of action. The body:
  5. 5.A force F acts at a distance r from an axis, at an angle θ to r. Its torque is greatest when θ is:
  6. 6.The perpendicular distance from the axis of rotation to the line of action of a force is called the: