BISE Gujranwala · Punjab Class 9
BISE Gujranwala Annual 2023 Class 9 Physics (Objective, Group I) (5477)
Set by BISE Gujranwala for Punjab Class 9 Physics, Annual 2023: 15 minutes and 12 marks, on Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science. The paper itself is on BISE Gujranwala’s website; this page adds what it covers, how to use it and original practice questions on the same topics.
Paper facts
- Series
- Annual 2023
- Paper
- Objective, Group I
- Set by
- BISE Gujranwala
- Code
- 5477
- Tier
- Not tiered
- Time
- 15 minutes
- Marks
- 12
- Calculator
- Not recorded here: check the paper’s instructions
- Syllabus
- Old Punjab syllabus (PCTB Physics 9 used until the 2024-25 session), not the NC 2023 book. Some questions, such as satellites and heat transfer, are not in the new course.
- Links checked
- 17 November 2026
Official files
- Question paper(opens BISE Gujranwala’s website)
- Mark schemenot public
- Examiner reportnot public
These files belong to BISE Gujranwala. Labverse links to them and never hosts or copies them. Labverse is not affiliated with BISE Gujranwala.
What this paper covers
8 topic groups from our map of Punjab Board Class 9 Physics. Revise each one with its topic pages and simulations before you sit the paper.
- Physical quantities and measurements
Physical quantities and SI units · Prefixes and scientific notation · Vernier callipers · Micrometer screw gauge · Measuring mass and time · Measuring cylinders and displacement cans · Errors and uncertainty in measurements · Significant figures · Precision and accuracy
Significant figures, prefixes and units trainerVernier caliperMicrometer screw gaugeMeasuring density
- Kinematics
Scalars and vectors · Types of motion · Distance and displacement · Speed and velocity · Acceleration · Distance–time graphs · Speed–time graphs · Equations of motion · Free fall acceleration
Adding and resolving vectorsDistance and displacementMotion graphsSUVAT equations of motion
- Dynamics
Contact and non-contact forces · Newton's law of gravitation · Fundamental forces · Free-body diagrams · Newton's first law · Newton's second law · Newton's third law · Mass, weight and balances · Friction · Terminal velocity · Momentum and impulse · Conservation of momentum
Free-body diagrams and resultant forceStatic and kinetic frictionOrbits and gravityWeight, mass and gravity
- Turning effects of force
Parallel forces and addition of forces · Torque (moment of force) and couple · Resolution of vectors · Principle of moments · Centre of mass and centre of gravity · Equilibrium and its conditions · States of equilibrium and stability · Circular motion and centripetal force
Adding and resolving vectorsPrinciple of momentsCentre of mass and stabilityFree-body diagrams and resultant force
- Work, energy and power
Work · Kinetic energy · Potential energy · Conservation of energy · Renewable and non-renewable energy sources · Power · Efficiency
Work doneEnergy skate trackEnergy stores and transfersEnergy resources
- Mechanical properties of matter
Elasticity and Hooke's law · Density · Pressure · Pressure in liquids · Atmospheric pressure · Barometers and manometers · Pascal's law and hydraulic systems
Hooke's law and springsMeasuring densityPressure in solidsLiquid pressure and depth
- Thermal properties of matter
Kinetic molecular theory of matter · Plasma: the fourth state of matter · Temperature, heat and internal energy · Liquid-in-glass and thermocouple thermometers · Temperature scales and conversions · Sensitivity, range and linearity
- Nature of science
Physics and its branches · Interdisciplinary research · Scientific method: hypothesis, theory and law · Science, technology and engineering
How to use this paper
- 1. Time it. Set 15 minutes for 12 marks: about 75 seconds a mark. At 8 minutes you should be roughly halfway through the marks; if you’re well behind, speed up on the short questions.
- 2. Sit it in one go. Open the question paper on BISE Gujranwala’s website (the link above) and work on paper, with no notes.
- 3. Mark it with the official scheme. The mark scheme isn’t public, so check answers with your teacher, and use the marking points on our questions below to practise marking.
- 4. Learn from the marks you lost. For every lost mark, note whether it was knowledge, method, reading the question or time.
- 5. Log mistakes by topic. Keep one line per topic group (Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science) and add a tally each time a mark goes there.
- 6. Revisit, then redo. Work through the weakest group’s topic pages and simulations, try the questions below, and come back to the paper in a week.
Practise the same topics
8 original exam-style questions on this paper’s topics, written in the style of Punjab board exams (not taken from the paper). Try each one before you reveal the answer.
1.A student uses a measuring cylinder to measure the volume of some water.
From the topic: Measuring cylinders and displacement cans
(a)What is meant by the meniscus?
1 markShow the answerHide the answer
Answer: The curved surface of a liquid in a narrow tube or cylinder.
Marking points
- Curved surface of the liquid in the cylinder
(b)Where should the scale be read for (i) water, (ii) mercury?
2 marksShow the answerHide the answer
Answer: (i) Water: level with the bottom of the concave meniscus. (ii) Mercury: level with the top of the convex meniscus.
Marking points
- Water: bottom of the meniscus
- Mercury: top of the meniscus
(c)The student reads the scale while looking down at the surface from above. Name the error made and state whether the reading is too high or too low.
2 marksShow the answerHide the answer
Answer: Parallax error. Looking down from above makes the reading too high.
Marking points
- Parallax error
- Reading too high
2.A student notes the distance covered by a van on Jail Road every 10 s. Time t: 0, 10, 20, 30, 40 s. Distance S: 0, 120, 240, 360, 480 m.
From the topic: Distance–time graphs
(a)What shape will the distance–time graph of this data have? Give a reason.
2 marksShow the answerHide the answer
Answer: A straight line sloping upwards from the origin, because the van covers equal distances (120 m) in equal intervals of time (10 s).
Marking points
- Straight line sloping upwards (through the origin)
- Equal distances in equal time intervals, i.e. uniform speed
(b)Use the gradient of the graph to find the speed of the van.
2 marksShow the answerHide the answer
Answer: Gradient = (480 − 0) ÷ (40 − 0) = 12 m s⁻¹, so the speed is 12 m s⁻¹.
Marking points
- Gradient = change in distance ÷ change in time, using any correct pair of points
- 12 m s⁻¹
(c)If the van keeps the same speed, how far will it have travelled after 55 s?
1 markShow the answerHide the answer
Answer: S = vt = 12 × 55 = 660 m
Marking points
- 660 m
3.A heavy box rests on a level floor. A student pushes it gently at first, then harder until it moves.
From the topic: Friction
(a)What is meant by static friction and limiting friction?
2 marksShow the answerHide the answer
Answer: Static friction is the friction acting on a body that is pushed or pulled but is still at rest; it balances the applied force. Limiting friction is the maximum value of static friction, reached just before the body starts to slide.
Marking points
- Static friction: acts while the body is at rest, opposing the applied force
- Limiting friction: the maximum value of static friction
(b)State two differences between static friction and kinetic friction.
2 marksShow the answerHide the answer
Answer: Static friction acts before motion starts and changes to match the applied force; kinetic friction acts while the body slides and stays constant on a given surface. Kinetic friction is usually smaller than the limiting friction.
Marking points
- Static acts at rest and equals the applied force; kinetic acts during sliding and stays constant
- Kinetic friction is less than limiting (maximum static) friction
4.Every body that falls through the air experiences air resistance.
From the topic: Terminal velocity
(a)What is meant by terminal velocity?
2 marksShow the answerHide the answer
Answer: Terminal velocity is the constant (maximum) velocity reached by a body falling through air, when the upward air resistance becomes equal to its weight so that the resultant force on it is zero.
Marking points
- The constant (steady, maximum) velocity of a falling body
- Air resistance has become equal to the weight (resultant force zero)
(b)State two factors on which the air resistance acting on a falling body depends.
2 marksShow the answerHide the answer
Answer: Its speed (greater speed, greater air resistance) and its surface area facing the air (larger area, greater air resistance). Its shape is also accepted.
Marking points
- Speed of the body
- Surface area facing the air (or shape)
5.Doors, taps and spanners all rely on the turning effect of a force.
From the topic: Torque (moment of force) and couple
(a)Define torque and write its SI unit.
2 marksShow the answerHide the answer
Answer: Torque (moment of force) is the product of the force and its moment arm, τ = F × ℓ. Its SI unit is the newton metre (N m).
Marking points
- Torque = force × moment arm (perpendicular distance from the axis to the line of action)
- Unit N m
(b)Explain why a door handle is fixed far from the hinges.
2 marksShow the answerHide the answer
Answer: Torque = force × moment arm. A handle far from the hinges has a large moment arm, so a small force produces enough torque to turn the door.
Marking points
- Large moment arm (distance from the axis/hinges)
- Less force needed for the same torque
6.A shopkeeper drags a sack of rice 6.0 m across a level floor by pulling on a rope with a force of 200 N.
From the topic: Work
(a)Calculate the work done by the pull when the rope is parallel to the floor.
2 marksShow the answerHide the answer
Answer: W = FS = 200 N × 6.0 m = 1200 J.
Marking points
- W = FS = 200 × 6.0
- 1200 J
(b)The rope is now held at 60° to the floor, with the same 200 N pull over the same 6.0 m. Calculate the work done.
2 marksShow the answerHide the answer
Answer: W = FS cos θ = 200 × 6.0 × cos 60° = 200 × 6.0 × 0.5 = 600 J.
Marking points
- W = FS cos θ = 200 × 6.0 × cos 60°
- 600 J
(c)Explain why less work is done in the second case, even though the pull is the same.
2 marksShow the answerHide the answer
Answer: Only the component of the pull along the floor, F cos θ = 100 N, does work. The component at right angles to the floor, F sin θ, is perpendicular to the motion and does no work.
Marking points
- Only the component F cos θ along the motion does work
- The perpendicular component F sin θ does no work
7.A spring with a spring constant of 200 N m⁻¹ hangs vertically. A 500 g mass is hung from it. Take g = 10 m s⁻².
From the topic: Elasticity and Hooke's law
(a)Calculate the weight of the mass.
1 markShow the answerHide the answer
Answer: w = mg = 0.500 kg × 10 m s⁻² = 5.0 N.
Marking points
- 0.500 × 10 = 5.0 N
(b)Calculate the extension of the spring in centimetres.
2 marksShow the answerHide the answer
Answer: x = F/k = 5.0 N ÷ 200 N m⁻¹ = 0.025 m = 2.5 cm.
Marking points
- x = F/k = 5.0 ÷ 200 = 0.025 m
- 2.5 cm
(c)A second mass is added and the total extension becomes 4.0 cm, still within the elastic limit. Find the size of the second mass.
3 marksShow the answerHide the answer
Answer: Total load F = kx = 200 × 0.040 = 8.0 N. Total mass = 8.0 ÷ 10 = 0.80 kg. Second mass = 0.80 − 0.50 = 0.30 kg = 300 g.
Marking points
- F = kx = 200 × 0.040 = 8.0 N
- Total mass = 8.0 ÷ 10 = 0.80 kg
- Second mass = 0.30 kg (300 g)
8.The kinetic molecular theory describes matter in terms of moving molecules.
From the topic: Kinetic molecular theory of matter
(a)State any three postulates of the kinetic molecular theory of matter.
3 marksShow the answerHide the answer
Answer: Any three of: matter is made of very small particles called molecules; the molecules are always in motion; molecules attract each other with an intermolecular force that becomes weaker as the distance between them increases; molecules have kinetic energy because they move and potential energy because they attract each other; the temperature of a substance depends on the average kinetic energy of its molecules.
Marking points
- First correct postulate, e.g. matter consists of very small particles called molecules
- Second correct postulate, e.g. the molecules are always in motion
- Third correct postulate, e.g. molecules attract each other with a force that weakens with distance; they have kinetic and potential energy; or temperature depends on their average kinetic energy
(b)Name the three kinds of motion that molecules may have, and state which kind is the main motion of the molecules in a solid.
2 marksShow the answerHide the answer
Answer: Vibrational, rotational and linear (translational) motion. In a solid the molecules mainly vibrate about fixed positions.
Marking points
- Vibrational, rotational and linear (translational)
- Vibrational motion in a solid
(c)What is meant by intermolecular force, and how does it change as the distance between two molecules increases?
2 marksShow the answerHide the answer
Answer: It is the force of attraction between molecules. It becomes weaker as the molecules move further apart.
Marking points
- Force of attraction between molecules
- Decreases as the distance between them increases