What is friction?
A carrom striker flicked across the board soon stops. The force that stops it is friction: a force that opposes the motion of one surface over another, or a body's tendency to start moving.
Friction is a dissipative force. Work done against it turns useful energy into heat, which is lost. Rubbed palms warm up, and a drill bit gets hot as it bores into wood.
Sliding friction: static and kinetic
Friction between two solid surfaces is called sliding friction. It has two kinds, static and kinetic.
- Static friction () acts on a body that is being pulled or pushed but has not started moving. It is only as large as it needs to be: while the body stays at rest, is equal and opposite to the applied force.
- Limiting friction is the greatest value static friction can reach. Pull harder than this and the body starts to slide.
- Kinetic friction acts while the body is sliding. It is usually a little smaller than the limiting friction, which is why a heavy almirah is hardest to push at the very start.
Worked numerical 1: pushing an almirah
A 40 kg almirah stands on a level floor. Its limiting friction is 160 N and its kinetic friction is 120 N. Find the friction and the acceleration for a push of (a) 100 N and (b) 200 N.
(a) 100 N is less than the limiting friction, so the almirah stays at rest. Static friction balances the push: and .
(b) 200 N is more than 160 N, so the almirah slides and kinetic friction (120 N) acts.
To keep it sliding at a constant velocity, the push must equal the kinetic friction, 120 N.
Rolling friction
When a body rolls over a surface instead of sliding, the friction is called rolling friction. It is much smaller than sliding friction; your textbook puts it at roughly one hundredth. The part of a wheel touching the ground is at rest on it for an instant, so the two surfaces do not rub past each other, and they touch over only a tiny patch. That is why a wheeled suitcase is easier to move than one dragged flat, and why machines use ball bearings.
Friction: useful and harmful
| Useful | Harmful |
|---|---|
| Lets us walk and run without slipping | Wastes energy as heat in engines and machines |
| Brakes and tyres stop vehicles; tread grooves keep tyres gripping wet roads | Wears out tyres, shoe soles and moving parts |
| Holds nails and screws in place, and lets a pencil write | Means extra fuel is burnt to overcome it |
Ways to reduce friction
- Polish surfaces that slide over each other, so they are smoother.
- Lubricate them with oil or grease. Friction in a liquid is much less than between dry solids.
- Use ball bearings or wheels, which change sliding into rolling.
- Streamline cars, aeroplanes and boats so that air or water flows smoothly past them.
Worked numerical 2: braking
A 1200 kg car moving at brakes. On a dry road the friction from the road is 6000 N; on a wet road with worn tyres it is only 3000 N. Find the stopping time in each case.
Using the simulation
In the simulation above, a 2 kg Wooden block on wood rests on a bench and the Normal contact force reads 20.0 N (g = 10 N/kg). Press Pull beside Play: the pull grows by 2 N every second. While the block stays still, the Friction readout copies the pull and says static, can reach 10.0 N. That is static friction, and 10.0 N is the limiting friction.
Just after the pull passes 10.0 N the block slips, and the stage reports that friction drops from 10.0 N to 6.00 N, the kinetic friction. Press Pull again to hold the force: the block keeps speeding up. Now drag the Applied force slider down to 6 N. The resultant force is zero and the block slides at a steady speed.
Change Block on surface to Steel block on ice. The Limit line on the Friction against applied force graph falls to 0.800 N: smoother surfaces give less friction. Rubber block on concrete raises it to 20.0 N. The coefficients μs and μk shown in the simulation are a model detail; your course does not ask for them. The simulation has no wheels, so it does not show rolling friction.