Skip to content

Punjab Board Class 9 Physics · Mechanical properties of matter

Atmospheric pressure

Section 6.6

Atmospheric pressure is the force per unit area produced by air molecules striking a surface. It acts equally in all directions and is about 1.013 × 10⁵ Pa at sea level. A crumpling tin can shows its strength. The pressure falls with altitude because the air thins out and less of it lies overhead.

Loading simulation…

Symbols match your course. Open the full atmospheric pressure and altitude simulation for more presets and teacher tools.

Section 6.6 in brief

Section 6.6 covers what atmospheric pressure is, its value at sea level, the tin can evidence (Activity 6.5) and how the pressure changes with height. Measuring it is on the Barometers and manometers page.

What causes it

The atmosphere is the blanket of air that covers the Earth. As the kinetic molecular theory describes, the gas molecules in air dart about at random and at high speed. Every surface in the air, from the ground to your skin, is struck by them all the time. Each strike is a tiny push, and the combined push per square metre is the atmospheric pressure.

The strikes come from all sides, so the pressure is the same in every direction at a point. It presses down on the top of a table, up on its underside and sideways on its legs.

How large is it?

Standard atmospheric pressure, the typical value at sea level, is 1.013×1051.013 \times 10^5 Pa, also called one atmosphere. That is roughly 10 N on each square centimetre, as if a 1 kg mass rested on every fingernail-sized patch of your skin.

Why are we not crushed? Air and fluids inside the body push outwards with nearly the same pressure, so the push from outside is balanced.

Worked numerical 1: air on a table top

A study table has a flat top 1.2 m long and 0.60 m wide. What force does the atmosphere exert on the top? Take P=1.013×105P = 1.013 \times 10^5 Pa.

Data: A=1.2 m×0.60 m=0.72 m2A = 1.2\ \text{m} \times 0.60\ \text{m} = 0.72\ \text{m}^2, F=?F = ?

F=PA=1.013×105 Pa×0.72 m2≈7.3×104 NF = PA = 1.013 \times 10^{5}\ \text{Pa} \times 0.72\ \text{m}^{2} \approx 7.3 \times 10^{4}\ \text{N}

That equals the weight of a 7300 kg mass (g = 10 m s⁻²). The table survives because the air underneath pushes up almost equally hard.

Evidence: the tin can (Activity 6.5)

  1. A little water is boiled in an open tin can. Steam fills the can and pushes most of the air out.
  2. The burner is removed and a cork is pushed firmly into the opening, sealing the can.
  3. Cold water is poured over the can. The steam condenses into a few drops, leaving very little gas to push outwards.
  4. The atmosphere outside now pushes much harder than the gas inside, so the can crumples.

The can is not sucked in: nothing inside pulls on the walls. The air outside pushes them in.

Worked numerical 2: the push on the can

After sealing and cooling, the gas left in a can is at 1.5×1041.5 \times 10^4 Pa while the air outside is at 1.013×1051.013 \times 10^5 Pa. One flat side of the can measures 18 cm by 12 cm. Find the resultant force on that side.

Data: A=0.18 m×0.12 m=2.16×10−2 m2A = 0.18\ \text{m} \times 0.12\ \text{m} = 2.16 \times 10^{-2}\ \text{m}^2

ΔP=1.013×105−0.15×105=8.63×104 Pa\Delta P = 1.013 \times 10^{5} - 0.15 \times 10^{5} = 8.63 \times 10^{4}\ \text{Pa}

F=ΔP×A=8.63×104×2.16×10−2≈1.9×103 NF = \Delta P \times A = 8.63 \times 10^{4} \times 2.16 \times 10^{-2} \approx 1.9 \times 10^{3}\ \text{N}

This force acts inwards, easily enough to fold thin metal.

Pressure and height

The lowest air carries the weight of everything above it, so it is squeezed hardest and is densest at sea level. Its density decreases as you go up. Higher up there is also less air overhead, so the pressure is lower: at about 5.5 km it is around half the sea-level value. In Murree, about 2.3 km above sea level, the air pressure is roughly three quarters of its value on the beach at Karachi.

Because pressure falls with height in a known way, a pressure reading can be converted into a height above sea level. Aircraft altimeters work like this.

The balloon and the can in the simulation

In the simulation above, a balloon waits at sea level. Air pressure shows 101.3 kPa, and the working gives the weight of air above 1 cm² as 10.1 N. On a phone, the cards are under the Readings tab.

  1. Press Play and watch the balloon climb to 15 km while the Air density card falls from 1.225 kg m⁻³.
  2. After the balloon stops, pick Everest, 8.8 km in the Go to… menu. The pressure is 31.7 kPa in the simulation's model (readings measured on the summit are about 34 kPa), and Air still above you says 31%.
  3. Choose Sea level from Go to…, then pick Collapsing can from the scene menu. Press Heat. When the status line reports boiling, wait a few seconds, then press Seal and Cool. Inside the can falls far below Outside the can, the Push on the front face grows to a few kilonewtons, and the can collapses.
  4. Press Reset, set the Altitude slider to 5.0 km and repeat. With less air pressure outside, the can only dents.

Common mistakes

  • Saying the tin can in Activity 6.5 is sucked inwards. Nothing inside pulls: the pressure inside drops when the steam condenses, and the air outside pushes the walls in.
  • Writing that atmospheric pressure acts only downwards. Molecules hit a surface from every side, so at any point the air pushes up, down and sideways just as hard.
  • Putting an area in cm² straight into F = PA. Change it to m² first by dividing by 10 000.
  • Thinking that atmospheric pressure is the same everywhere. It is greatest at sea level and decreases as altitude increases.
  • Expecting a large atmospheric force to break a window or a table. Air usually presses on both sides, so the forces balance; only a difference in pressure gives a resultant force.
  • Writing standard atmospheric pressure as 1.013 × 10³ Pa. The power of ten is 5: about 101 300 Pa.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.Answer these questions about atmospheric pressure.

    1. (a)What is meant by atmospheric pressure?

      2 marks
      Show the answer

      Answer: It is the force per unit area that the air of the atmosphere exerts on a surface. It is caused by air molecules colliding with the surface.

      Marking points

      • Force per unit area exerted by the air (atmosphere) on a surface
      • Caused by collisions of moving air molecules with the surface
    2. (b)State the value of standard atmospheric pressure at sea level.

      1 mark
      Show the answer

      Answer: About 1.013 × 10⁵ Pa.

      Marking points

      • 1.013 × 10⁵ Pa (101 300 N m⁻²)
    3. (c)Why does atmospheric pressure act equally in all directions?

      1 mark
      Show the answer

      Answer: Air molecules move randomly in every direction, so they strike a surface from every side.

      Marking points

      • Random motion of the molecules in all directions
    4. (d)Atmospheric pressure is very large, yet it does not crush our bodies. Explain why.

      2 marks
      Show the answer

      Answer: Air and fluids inside the body exert an outward pressure almost equal to atmospheric pressure. On every part of the skin, this outward push cancels the inward push of the air.

      Marking points

      • Fluids (and air) inside the body exert a nearly equal pressure outwards
      • So the inward and outward pushes balance
  2. 2.In a class demonstration, a tin can holding a little water is heated until steam pours from its opening. The heating stops, a tight cork seals the opening, and cold water is splashed over the can, which then caves in.

    1. (a)Why is the water heated until steam pours out before the can is sealed?

      2 marks
      Show the answer

      Answer: The steam pushes nearly all the air out through the mouth, so that after cooling very little gas is left inside.

      Marking points

      • Steam pushes (most of) the air out of the can
      • So little gas remains inside once the steam condenses
    2. (b)What happens to the steam when the cold water is poured over the can?

      1 mark
      Show the answer

      Answer: It condenses into a few drops of water.

      Marking points

      • It condenses (turns back into liquid water)
    3. (c)Explain why the can caves in.

      3 marks
      Show the answer

      Answer: With the steam condensed, the pressure inside the can becomes much lower than atmospheric pressure. The air outside therefore pushes inwards on the walls much harder than the gas inside pushes outwards. This resultant inward force crushes the can; nothing pulls from inside.

      Marking points

      • Pressure inside falls far below atmospheric pressure
      • Atmospheric pressure outside is now greater than the pressure inside
      • The resultant force acts inwards and crushes the walls (pushed, not sucked)
    4. (d)What does this activity show?

      1 mark
      Show the answer

      Answer: The atmosphere exerts a large pressure on everything it surrounds.

      Marking points

      • The atmosphere exerts (a large) pressure
  3. 3.A classroom window pane is 1.5 m wide and 1.2 m high. Atmospheric pressure is 1.013 × 10⁵ Pa. Take g = 10 m s⁻².

    1. (a)Calculate the force that the atmosphere exerts on one side of the pane.

      2 marks
      Show the answer

      Answer: A = 1.5 × 1.2 = 1.8 m². F = PA = 1.013 × 10⁵ × 1.8 = 1.82 × 10⁵ N.

      Marking points

      • A = 1.8 m² and F = PA
      • F = 1.82 × 10⁵ N
    2. (b)Find the mass whose weight equals this force.

      2 marks
      Show the answer

      Answer: m = F/g = 1.82 × 10⁵ ÷ 10 = 1.82 × 10⁴ kg.

      Marking points

      • m = F/g
      • 1.82 × 10⁴ kg
    3. (c)Explain why the pane does not break.

      2 marks
      Show the answer

      Answer: Air inside the classroom presses on the inner face with the same force, so the forces balance and the resultant force is zero.

      Marking points

      • Air in the room pushes on the pane with an equal, opposite force
      • Resultant force is zero
    4. (d)During a storm, the pressure outside falls to 1.003 × 10⁵ Pa for a moment while the air in the room stays at 1.013 × 10⁵ Pa. Find the resultant force on the pane and its direction.

      2 marks
      Show the answer

      Answer: ΔP = 1.013 × 10⁵ − 1.003 × 10⁵ = 1.0 × 10³ Pa. F = ΔP × A = 1.0 × 10³ × 1.8 = 1.8 × 10³ N, pushing outwards.

      Marking points

      • ΔP = 1.0 × 10³ Pa and F = ΔP × A
      • 1.8 × 10³ N, outwards
  4. 4.Atmospheric pressure changes with altitude.

    1. (a)How does atmospheric pressure change as we go up from sea level? Give two reasons for this change.

      3 marks
      Show the answer

      Answer: It decreases. Less air lies overhead, so the air above weighs less. The air is also less dense, so fewer molecules strike each unit area every second.

      Marking points

      • Pressure decreases with altitude
      • Less air overhead, so the air above weighs less
      • Air less dense: fewer molecular collisions per unit area per second
    2. (b)Why is the air densest at sea level?

      1 mark
      Show the answer

      Answer: The air higher up rests on it and squeezes it.

      Marking points

      • Squeezed by the air resting on it
    3. (c)Explain how a pressure reading can be used to find the altitude of an aeroplane.

      2 marks
      Show the answer

      Answer: Pressure falls with height in a known way, so each pressure matches one altitude. A lower reading means the aeroplane is higher; an altimeter is marked to show the altitude directly.

      Marking points

      • Pressure decreases with height in a known way
      • Lower pressure means greater altitude (altimeter scale reads altitude)

Quick check

6 questions

  1. 1.Standard atmospheric pressure at sea level is about:
  2. 2.Atmospheric pressure is caused by:
  3. 3.As we go higher above sea level, atmospheric pressure:
  4. 4.In the tin can activity, the can crumples because:
  5. 5.Atmospheric pressure is 1.0 × 10⁵ Pa. The force it exerts on a flat area of 0.35 m² is:
  6. 6.At sea level, the force of the air on each square centimetre of a surface is about: