Skip to content

Punjab Board Class 9 Physics · Mechanical properties of matter

Pressure in liquids

Section 6.5

The pressure due to a liquid at depth h is P = ρgh, found from the weight of the liquid column above an area. It rises in proportion to the depth and to the density, acts equally in all directions at a point, pushes at right angles on every surface, and does not depend on the container's shape.

Loading simulation…

Symbols match your course. Open the full liquid pressure and depth simulation for more presets and teacher tools.

How a liquid presses

A liquid pushes on the base and walls of its container and on anything dipped into it. Recall two facts before the formula:

  • Inside a liquid, the pressure at a point acts equally in all directions: up, down and sideways.
  • The pressure increases with depth below the surface.

The push of a liquid on a surface is always at right angles to that surface. Make a pinhole in the side of a full plastic bottle. The thin stream of water starts out at right angles to the wall, and then gravity bends it down.

Deriving P = ρgh

Picture a flat, horizontal patch of area AA, a depth hh down in a liquid of density ρ\rho. The patch holds up the upright column of liquid standing on it.

  1. Volume of the column: V=AhV = Ah
  2. Mass of the column: m=ρV=ρAhm = \rho V = \rho A h
  3. Weight of the column, which is the force on the patch: F=w=mg=ρAhgF = w = mg = \rho A h g
  4. Pressure on the patch:
P=FA=ρAhgA⇒P=ρghP = \frac{F}{A} = \frac{\rho A h g}{A} \qquad \Rightarrow \qquad P = \rho g h

Put ρ\rho in kg m⁻³, g=10 m s−2g = 10\ \text{m s}^{-2} and hh in metres, measured straight down from the free surface. PP then comes out in pascals, because

kg m−3×m s−2×m=kg m−1 s−2=N m−2\text{kg m}^{-3} \times \text{m s}^{-2} \times \text{m} = \text{kg m}^{-1}\,\text{s}^{-2} = \text{N m}^{-2}

This is the pressure caused by the liquid alone. The air above the surface adds atmospheric pressure on top, which section 6.6 deals with.

What the pressure depends on

  • Depth. In one liquid, P∝hP \propto h. Each metre of water adds 10 000 Pa (with g = 10 m s⁻²), so the pressure due to the water 4 m down is twice its value 2 m down.
  • Density. At one depth, P∝ρP \propto \rho. Mercury is 13.6 times as dense as water, so it gives 13.6 times the pressure.
  • Not the area or the shape. AA cancelled out of the derivation. A slim pipe and a broad tank holding the same liquid to equal depths have the same pressure at the bottom. The tank holds more liquid, but its larger base shares that extra weight.

These ideas explain familiar designs. A dam wall is built thickest at its base, where the water presses hardest. The tap of a water cooler runs faster when the cooler is full than when it is nearly empty. A hospital drip bottle hangs well above the patient's arm, so the height of liquid gives enough pressure to push it into a vein.

Worked numerical 1: a canal bed

A canal carries water 4.2 m deep. What pressure does the water exert on the canal bed?

Data: ρ=1000 kg m−3\rho = 1000\ \text{kg m}^{-3}, g=10 m s−2g = 10\ \text{m s}^{-2}, h=4.2 mh = 4.2\ \text{m}, P=?P = ?

P=ρgh=1000 kg m−3×10 m s−2×4.2 m=4.2×104 PaP = \rho g h = 1000\ \text{kg m}^{-3} \times 10\ \text{m s}^{-2} \times 4.2\ \text{m} = 4.2 \times 10^{4}\ \text{Pa}

Worked numerical 2: which oil?

A gauge 1.5 m down in the oil of a storage tank reads 1.2 × 10⁴ Pa due to the oil. Find the density of the oil, taking g=10 m s−2g = 10\ \text{m s}^{-2}.

Data: P=1.2×104 PaP = 1.2 \times 10^{4}\ \text{Pa}, h=1.5 mh = 1.5\ \text{m}, ρ=?\rho = ?

ρ=Pgh=1.2×104 Pa10 m s−2×1.5 m=800 kg m−3\rho = \frac{P}{gh} = \frac{1.2 \times 10^{4}\ \text{Pa}}{10\ \text{m s}^{-2} \times 1.5\ \text{m}} = 800\ \text{kg m}^{-3}

That is close to the density of kerosene oil.

Exploring the probe, liquids and jets

In the simulation above, a tall tank holds Water 1.00 m deep, and the probe sits 0.50 m below the surface. The Pressure at the probe card reads 5000 Pa, and the working shows P = ρ × g × h = 1000 × 10 × 0.50 = 5000 Pa.

  1. Drag the probe, or use the Probe depth slider, until the Probe depth card reads 1.00 m. The reading doubles to 10000 Pa. On the Pressure against depth graph, the water line is straight and passes through the origin, with gradient ρg = 10000 Pa m⁻¹.
  2. Look at The shape does not matter. Four connected vessels of very different widths and shapes are filled to the same depth, and the pressure at the probe's level is the same in each one.
  3. Choose Mercury from the Liquid menu. The probe now reads 1.36 × 10⁵ Pa, which is 13.6 times the water reading. Cooking oil gives 9200 Pa.
  4. Press Play to pull out the bungs. Each stream comes out at right angles to the wall, then bends down. The jets table, an extension beyond Class 9, shows the lowest jet spurting out fastest, because the pressure there is greatest. Where a jet lands also depends on how high its hole is above the tray, so judge pressure by speed, not by landing point.
  5. The tap starts on, keeping the level steady. Press Top up to turn it off: as the level falls, the depth above the probe shrinks and so does the reading.

Switching on Add atmospheric pressure (total) adds the push of the air, taken as 1.01 × 10⁵ Pa.

Equations

  • Pressure in a liquid

    Learn this

    P=ρgh

    pressure due to a column of liquid = height of column × density of liquid × gravitational field strength

    Open calculator →

Common mistakes

  • Measuring h up from the bottom of the container. In P = ρgh, h is the depth below the free surface of the liquid.
  • Leaving the depth in centimetres. Change it to metres before substituting: 45 cm = 0.45 m.
  • Putting a density in g cm⁻³ straight into P = ρgh. Multiply by 1000 first, so 0.80 g cm⁻³ becomes 800 kg m⁻³.
  • Thinking that a wider or bigger container gives a larger pressure at the same depth. The area cancels in the derivation, so only ρ, g and h matter. A bigger base feels a bigger force, but not a bigger pressure.
  • Saying that liquid pressure acts only downwards. At a point it acts equally in all directions, and on any surface it pushes at right angles.
  • Using the slanting length of a sloping tube as h. Only the vertical depth below the surface counts.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.A liquid of density ρ is at rest in a container. A horizontal area A lies at a depth h below the surface, with a column of liquid standing on it.

    1. (a)Write expressions for the volume and the mass of the liquid column above the area.

      2 marks
      Show the answer

      Answer: V = Ah, and m = ρV = ρAh.

      Marking points

      • V = Ah
      • m = ρV = ρAh
    2. (b)Hence show that the pressure on the area is P = ρgh.

      3 marks
      Show the answer

      Answer: The force on the area is the weight of the column: F = w = mg = ρAhg. Then P = F/A = ρAhg ÷ A. The area cancels, leaving P = ρgh.

      Marking points

      • F = w = mg = ρAhg
      • P = F/A = ρAhg ÷ A
      • A cancels, giving P = ρgh
    3. (c)Explain why A does not appear in the final equation, and what this means for containers of different widths.

      2 marks
      Show the answer

      Answer: The weight of the column is proportional to A, so dividing by A cancels it. The pressure at a given depth is therefore the same whatever the width or shape of the container.

      Marking points

      • The column's weight is proportional to A, so A cancels
      • Same pressure at a given depth in a container of any width or shape
    4. (d)Show that the unit of ρgh is N m⁻².

      2 marks
      Show the answer

      Answer: kg m⁻³ × m s⁻² × m = kg m⁻¹ s⁻². Since 1 N = 1 kg m s⁻², this is (kg m s⁻²) m⁻² = N m⁻².

      Marking points

      • kg m⁻³ × m s⁻² × m = kg m⁻¹ s⁻²
      • Using N = kg m s⁻², this is N m⁻²
  2. 2.The water in a farm's fish pond stands 2.4 m deep (ρ = 1000 kg m⁻³, g = 10 m s⁻²).

    1. (a)What pressure does the water exert on the bed of the pond?

      2 marks
      Show the answer

      Answer: P = ρgh = 1000 × 10 × 2.4 = 2.4 × 10⁴ Pa.

      Marking points

      • P = ρgh = 1000 × 10 × 2.4
      • 2.4 × 10⁴ Pa (24 000 N m⁻²)
    2. (b)A fish swims 0.90 m above the bed. What is the water pressure on the fish?

      2 marks
      Show the answer

      Answer: Depth below the surface = 2.4 m − 0.90 m = 1.5 m. P = 1000 × 10 × 1.5 = 1.5 × 10⁴ Pa.

      Marking points

      • h = 2.4 − 0.90 = 1.5 m
      • P = 1.5 × 10⁴ Pa
    3. (c)At what depth in the pond is the pressure due to the water 6.0 × 10³ Pa?

      2 marks
      Show the answer

      Answer: h = P/(ρg) = 6.0 × 10³ ÷ (1000 × 10) = 0.60 m.

      Marking points

      • h = P/(ρg) = 6000 ÷ 10 000
      • 0.60 m
  3. 3.An underground water tank, with a flat base 1.5 m long and 1.0 m wide, is filled to a depth of 1.2 m with water of density 1000 kg m⁻³ (g = 10 m s⁻²).

    1. (a)Work out the pressure that the water exerts on the base of the tank.

      2 marks
      Show the answer

      Answer: P = ρgh = 1000 × 10 × 1.2 = 1.2 × 10⁴ Pa.

      Marking points

      • P = 1000 × 10 × 1.2
      • 1.2 × 10⁴ Pa
    2. (b)Find the total force that the water exerts on the base.

      2 marks
      Show the answer

      Answer: A = 1.5 m × 1.0 m = 1.5 m². F = PA = 1.2 × 10⁴ Pa × 1.5 m² = 1.8 × 10⁴ N.

      Marking points

      • A = 1.5 m² and F = PA
      • 1.8 × 10⁴ N
    3. (c)A second tank has a base of twice this area and holds water to the same depth. State the pressure and the force on its base.

      2 marks
      Show the answer

      Answer: The pressure is unchanged at 1.2 × 10⁴ Pa, because the depth and the liquid are the same. The force doubles to 3.6 × 10⁴ N, because F = PA and the area is doubled.

      Marking points

      • Pressure still 1.2 × 10⁴ Pa
      • Force doubles to 3.6 × 10⁴ N
  4. 4.Use ideas about pressure in liquids to explain each of the following.

    1. (a)The wall of a dam is much thicker at the bottom than at the top.

      2 marks
      Show the answer

      Answer: Liquid pressure increases with depth (P = ρgh), so the water pushes hardest on the lowest part of the wall. The base must be thickest to withstand this greater pressure.

      Marking points

      • Pressure increases with depth
      • Greatest pressure at the base, so the wall must be strongest there
    2. (b)A small leak in the curved side of a water cooler sends out a thin jet, which first leaves along a line perpendicular to the cooler's surface.

      2 marks
      Show the answer

      Answer: A liquid presses at right angles on every surface it touches, so the water is pushed out along the normal to the surface at the hole. Gravity then bends the jet downwards.

      Marking points

      • Liquid pressure acts at right angles (normally) to the surface
      • So the jet leaves along the normal, then gravity curves it down
    3. (c)A drip bottle in a hospital is hung well above the patient's arm.

      2 marks
      Show the answer

      Answer: Raising the bottle increases the height of liquid above the needle, so the pressure there (ρgh) increases. This pressure is large enough to push the liquid into the vein.

      Marking points

      • Greater height of liquid gives greater pressure (P = ρgh)
      • The pressure is enough to push the liquid into the vein

Quick check

6 questions

  1. 1.The pressure due to a liquid at depth h below its surface is:
  2. 2.With g = 10 m s⁻², the pressure due to water (ρ = 1000 kg m⁻³) at a depth of 3.0 m is:
  3. 3.At the same depth, how does the pressure due to mercury (13 600 kg m⁻³) compare with the pressure due to water (1000 kg m⁻³)?
  4. 4.The depth of water in a tank is doubled. The pressure due to the water on the base becomes:
  5. 5.A probe in a salt solution of density 1200 kg m⁻³ reads 6000 Pa due to the liquid. With g = 10 m s⁻², how deep is the probe?
  6. 6.Which statement about the pressure at a point in a liquid at rest is correct?