Skip to content

Cambridge IGCSE Physics (0625) · Forces

Pressure

1.8

Pressure is force per unit area; recall and use p = F/A, and explain everyday examples where the force or the area changes. Core also describes how liquid pressure grows with depth and with density. Supplement adds Δp = ρgΔh, also recalled, with pressure in pascals.

Loading simulation…

Symbols match your course. Open the full pressure in solids simulation for more presets and teacher tools.

What this topic covers

A sharp knife slices a mango with a gentle push, while the back of the blade barely marks it. Topic 1.8 explains why, then looks inside liquids, where pressure grows with depth.

Pressure from a force (Core)

Pressure is force per unit area: how hard a force presses on each square metre of a surface.

p=FAp = \frac{F}{A}
  • pp: pressure, in N/m² (or N/cm²)
  • FF: the force pushing at right angles on the surface, in newtons (N)
  • AA: area the force acts on, in m² (or cm²)

You need to remember this equation. Dividing newtons by cm² gives N/cm². A square metre holds 100 × 100 = 10 000 cm², so multiply by 10 000 to convert N/cm² to N/m². A square metre is also 1 000 000 mm².

Everyday examples (Core)

With the area fixed, a bigger force gives a bigger pressure: stack a second brick on the first and the pressure on the sand below doubles. With the force fixed, a smaller area raises the pressure and a larger area lowers it.

ExampleContact areaPressure and result
Knife edge, needle pointTinyVery large: cuts or pierces with a light push
Snowshoes, wide tractor tyresLargeSmall: less sinking into snow or mud
Wide straps on a heavy bagLargeSmall: the straps do not dig into your shoulders

Pressure in liquids (Core)

Below a liquid's surface, the pressure rises with depth. A deeper point has a taller column of liquid above it, so more weight bears down on each square metre. That is why dam walls are thickest at the bottom.

At the same depth, a denser liquid gives a bigger pressure: sea water (about 1030 kg/m³) presses slightly harder than fresh water (1000 kg/m³). The width and shape of the container make no difference.

The liquid pressure equation (Supplement)

Δp=ρgΔh\Delta p = \rho g \Delta h
  • Δp\Delta p: change in pressure, in pascals (Pa)
  • ρ\rho: density of the liquid, in kg/m³
  • gg: gravitational field strength, 9.8 N/kg
  • Δh\Delta h: change in depth, in m

Remember this one too. Δh\Delta h is the vertical distance between the two levels, even along a sloping pipe. From the surface down, Δh\Delta h is the depth, and Δp\Delta p is the pressure the liquid adds to the air pressure on its surface.

Worked example 1: a loaded bookshelf (Core)

A loaded bookshelf in a school library in Accra weighs 840 N. It stands on four feet, each touching the floor over 3.5 cm². Find the pressure on the floor in N/cm² and in N/m².

A=4×3.5=14 cm2p=FA=84014=60 N/cm2A = 4 \times 3.5 = 14\ \text{cm}^2 \qquad p = \frac{F}{A} = \frac{840}{14} = 60\ \text{N/cm}^2

In square metres, A=14÷10 000=0.0014 m2A = 14 \div 10\,000 = 0.0014\ \text{m}^2, so

p=8400.0014=600 000 N/m2p = \frac{840}{0.0014} = 600\,000\ \text{N/m}^2

Answer: 60 N/cm², which is 600 000 N/m² (60 × 10 000).

Worked example 2: a diver going deeper (Supplement)

A diver off the coast of Oman swims down from 3.0 m to 18.0 m below the surface of sea water of density 1030 kg/m³. Find the increase in pressure. Take g=9.8g = 9.8 N/kg.

Δh=18.0−3.0=15.0 m\Delta h = 18.0 - 3.0 = 15.0\ \text{m} Δp=ρgΔh=1030×9.8×15.0=151 410 Pa\Delta p = \rho g \Delta h = 1030 \times 9.8 \times 15.0 = 151\,410\ \text{Pa}

Answer: about 1.5×1051.5 \times 10^5 Pa (151 kPa). Using 18.0 m instead of the change in depth wrongly gives about 182 000 Pa.

Simulation tasks

In the simulation above, a 2.0 kg Brick lies flat on Dry sand, with Weight 19.6 N, Contact area 0.0200 m² and Pressure 980 Pa. The simulation uses pascals; for a Core answer, read 980 Pa as 980 N/m².

  1. (Core) Predict the pressure on the 50 cm² end, then press End. The weight stays at 19.6 N, but the Pressure arrows lengthen and the pressure becomes 3920 Pa: a quarter of the area, four times the pressure.
  2. (Core) Press Side: half the flat face's area, twice its pressure (1960 Pa).
  3. (Core) Press Flat, then choose Steel under The block. Same area, but the weight is 77.4 N and the pressure 3870 Pa.
  4. (Core) Switch to Everyday examples. The Knife compares two cases with the same 30 N push: first on the sharp edge, then on the back of the blade. The edge's area is 100 times smaller, so its pressure is 100 times bigger.
  5. (Core, then Supplement) In the liquid pressure and depth simulation, drag the probe deeper and watch Pressure at the probe rise, then choose Mercury under Liquid and see it jump. Supplement candidates: choose Water, set Probe depth to 0.50 m and check Pressure at the probe against 1000×9.8×0.50=49001000 \times 9.8 \times 0.50 = 4900 Pa.

Equations

  • Pressure

    Learn this

    p=FA

    pressure = force normal to a surface ÷ area of that surface

    Open calculator →
  • Pressure in a liquid

    Learn this · Supplement

    Δp=ρgΔh

    pressure due to a column of liquid = height of column × density of liquid × gravitational field strength

    Open calculator →

Common mistakes

  • Dividing by 100 when changing cm² to m². A metre is 100 cm, so a square metre covers 100 × 100 square centimetres; divide by 10 000, and 360 cm² becomes 0.036 m², not 3.6 m².
  • Putting a mass into p = F/A. A 25 kg suitcase presses on the floor with its weight, 25 × 9.8 = 245 N, so divide 245 N by the area, not 25.
  • Mixing up N/cm² and N/m². Newtons divided by cm² give N/cm²; multiply by 10 000 to get N/m², because every square metre holds 10 000 square centimetres.
  • Thinking that the bigger force always gives the bigger pressure. A light push on a needle point can give a far greater pressure than a heavy crate on a wide base, because the area matters as much as the force.
  • Saying that a wider container, or one holding more liquid, has a greater pressure at the bottom. At the same depth in the same liquid, the pressure is equal, whatever the shape or width.
  • (Supplement) Using the depth of the lower point in Δp = ρgΔh when a question asks for the change between two depths. Subtract first: going from 4.0 m down to 10.0 m, Δh is 6.0 m, not 10.0 m.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A tractor working in a flooded rice field has a weight of 32 000 N. Its four tyres touch the mud over a total area of 0.80 m².

    1. (a)Define pressure.

      1 mark
      Show the answer

      Answer: Pressure is force per unit area.

      Marking points

      • force per unit area (force ÷ area)
    2. (b)Calculate the pressure that the tractor exerts on the mud. Give the unit.

      3 marks
      Show the answer

      Answer: p = F ÷ A = 32 000 ÷ 0.80 = 40 000 N/m²

      Marking points

      • p = F ÷ A, or 32 000 ÷ 0.80 seen
      • 40 000
      • N/m² (or Pa)
    3. (c)The farmer fits wider tyres, so that the area in contact with the mud becomes 1.6 m². Calculate the new pressure on the mud.

      1 mark
      Show the answer

      Answer: p = 32 000 ÷ 1.6 = 20 000 N/m²

      Marking points

      • 20 000 N/m² (or Pa)
    4. (d)Explain why the tractor is less likely to sink into the mud with the wider tyres.

      2 marks
      Show the answer

      Answer: The force on the mud, the tractor's weight, has not changed, but it is spread over a larger area, so the pressure on the mud is smaller.

      Marking points

      • force (weight) on the mud is unchanged
      • larger area, so smaller pressure
  2. 2.A wooden crate of weight 600 N rests on a level floor. Its base is a rectangle 50 cm long and 40 cm wide.

    1. (a)Calculate the area of the base in cm².

      1 mark
      Show the answer

      Answer: 50 × 40 = 2000 cm²

      Marking points

      • 2000 cm²
    2. (b)Calculate the pressure that the crate exerts on the floor, in N/cm².

      2 marks
      Show the answer

      Answer: p = 600 ÷ 2000 = 0.30 N/cm²

      Marking points

      • 600 ÷ 2000 seen
      • 0.30 N/cm²
    3. (c)Convert the area of the base to m², and use it to calculate the pressure in N/m².

      2 marks
      Show the answer

      Answer: A = 2000 ÷ 10 000 = 0.20 m², so p = 600 ÷ 0.20 = 3000 N/m²

      Marking points

      • 0.20 m²
      • 3000 N/m²
    4. (d)An identical crate is stacked on top of the first one. State the new pressure on the floor, in N/m², and explain your answer.

      2 marks
      Show the answer

      Answer: 6000 N/m². The force on the floor doubles to 1200 N, but the area of the base touching the floor stays the same.

      Marking points

      • 6000 N/m²
      • force doubles while the area stays the same
  3. 3.A dam holds back a lake of fresh water that is 45 m deep at the dam wall. The wall is much thicker at its base than at its top. The density of fresh water is 1000 kg/m³. Take g as 9.8 N/kg.

    1. (a)State how the pressure in the water changes as the depth below the surface increases.

      1 mark
      Show the answer

      Answer: The pressure increases as the depth increases.

      Marking points

      • pressure increases (with depth)
    2. (b)Explain why the wall is made thicker at its base.

      2 marks
      Show the answer

      Answer: The water is deepest at the base, so its pressure on the wall is greatest there. A thicker wall can withstand the larger pressure.

      Marking points

      • pressure is greatest at the base / at the greatest depth
      • thicker wall withstands the greater pressure (or force)
    3. (c)A second lake of fresh water is only half as long, but it is also 45 m deep at its dam. Compare the pressure at the base of its dam with the pressure at the base of the first dam. Give a reason.

      2 marks
      Show the answer

      Answer: The pressures are the same. The pressure depends only on the depth and the density of the water, not on how much water there is.

      Marking points

      • the same
      • pressure depends only on depth and density (not on the length or volume of the lake)
    4. (d)(Supplement) Calculate the change in pressure from the surface of the lake to the base of the wall.

      2 marks
      Show the answer

      Answer: Δp = ρgΔh = 1000 × 9.8 × 45 = 441 000 Pa (4.4 × 10⁵ Pa)

      Marking points

      • 1000 × 9.8 × 45 seen
      • 441 000 Pa / 4.4 × 10⁵ Pa
    5. (e)(Supplement) An outlet valve in the wall is 12 m below the surface. Calculate how much greater the pressure is at the base of the wall than at the valve.

      2 marks
      Show the answer

      Answer: Δh = 45 − 12 = 33 m, so Δp = 1000 × 9.8 × 33 = 323 400 Pa (3.2 × 10⁵ Pa)

      Marking points

      • Δh = 33 m
      • 323 400 Pa / 3.2 × 10⁵ Pa
  4. 4.A pressure sensor is lowered into a tall tank of cooking oil. As the sensor moves from 0.30 m to 0.80 m below the surface, its reading rises by 4508 Pa. Use 9.8 N/kg for g.

    1. (a)(Supplement) Write down the equation that links the change in pressure in a liquid with the density of the liquid, g and the change in depth.

      1 mark
      Show the answer

      Answer: Δp = ρgΔh

      Marking points

      • Δp = ρgΔh (or any correct rearrangement)
    2. (b)(Supplement) Calculate the density of the oil.

      3 marks
      Show the answer

      Answer: Δh = 0.80 − 0.30 = 0.50 m, so ρ = Δp ÷ (gΔh) = 4508 ÷ (9.8 × 0.50) = 920 kg/m³

      Marking points

      • Δh = 0.50 m
      • 4508 ÷ (9.8 × 0.50) seen
      • 920 kg/m³
    3. (c)(Supplement) The oil is replaced by water of density 1000 kg/m³. Calculate the rise in the reading as the sensor moves through the same 0.50 m.

      2 marks
      Show the answer

      Answer: Δp = 1000 × 9.8 × 0.50 = 4900 Pa

      Marking points

      • 1000 × 9.8 × 0.50 seen
      • 4900 Pa
    4. (d)(Supplement) State why the rise would be no different if the oil were in a much wider tank.

      1 mark
      Show the answer

      Answer: The pressure change depends only on the density, g and the change in depth, not on the width of the tank.

      Marking points

      • depends only on ρ, g and Δh (not on the width of the tank)

Quick check

6 questions

  1. 1.Which statement defines pressure?
  2. 2.A gas cylinder of weight 360 N stands on a base of area 0.040 m². What pressure does it exert on the floor?
  3. 3.A pressure of 25 N/cm² is the same as which of these?
  4. 4.A student pushes a drawing pin into a cork board. Which statement is correct?
  5. 5.At which of these points is the pressure caused by the liquid greatest? Cooking oil is less dense than water.
  6. 6.(Supplement) A submarine dives from 20 m to 50 m below the surface of sea water of density 1030 kg/m³. Taking g as 9.8 N/kg, by how much does the pressure on its hull increase?