Skip to content

Punjab Board Class 9 Physics · Mechanical properties of matter

Pressure

Section 6.4

Pressure is the normal force per unit area, P = F/A. Its SI unit is N m⁻², called the pascal (Pa). The same force gives a larger pressure on a smaller contact area, so needles and nails press hard, while broad feet, wide tyres and foundations spread a load and press gently.

Loading simulation…

Symbols match your course. Open the full pressure in solids simulation for more presets and teacher tools.

Same push, different result

Press a ball of atta with your flat palm, then just as hard with one fingertip. The palm leaves a shallow mark, but the fingertip sinks deep into the dough. The force is the same both times. Only the area carrying it changes. Pressure measures how much force each unit of that area carries.

Pressure is the normal force per unit area of a surface, where normal means at right angles to the surface. When a force FF acts at right angles to a surface over an area AA,

P=FAP = \frac{F}{A}

AA is the contact area: the part of the surface actually being pushed, not the whole surface of the object. A sideways drag along a surface does not press on it, so only the perpendicular part of a force counts.

The pascal

With force in newtons and area in square metres, pressure comes out in N m⁻². This unit is called the pascal (Pa):

1 Pa=1 N m−21\ \text{Pa} = 1\ \text{N m}^{-2}

One pascal is the pressure produced when a force of 1 N acts normally on an area of 1 m². That is tiny: a sheet of printer paper lying flat on a desk presses with less than 1 Pa. Bigger values are written in kilopascals, where 1 kPa = 1000 Pa.

Numericals often give areas in cm² or mm². Turn them into m² before dividing:

  • 1 cm² = 10⁻⁴ m², so divide a value in cm² by 10 000.
  • 1 mm² = 10⁻⁶ m², so divide a value in mm² by 1 000 000.

How force and area change pressure

For a larger pressureFor a smaller pressure
increase the forcereduce the force
reduce the contact areaincrease the contact area

With the area fixed, twice the force gives twice the pressure. With the force fixed, half the area gives twice the pressure.

Examples from daily life

Small areas give large pressures:

  • An injection needle has a very fine tip, so a gentle push on the syringe pierces the skin.
  • A nail is pointed, so each hammer blow is concentrated on a tiny patch of wood.

Large areas give small pressures:

  • Broad, padded feet spread a camel's weight over the loose sand of Cholistan, so it sinks in only a little.
  • A charpai on rain-soaked ground sinks in at each leg. A flat brick under every leg enlarges the contact area and stops the sinking.
  • A building's foundation is wider than its walls, so the soil beneath carries a lower pressure.

Worked numerical 1: an almirah on pads

A steel almirah weighs 1200 N and stands on four legs, each touching the floor over 3.0 cm². Find the pressure on the floor. Then find it again with a rubber pad of area 30 cm² under each leg.

Data: F=1200 NF = 1200\ \text{N}, A=4×3.0 cm2=12 cm2=1.2×10−3 m2A = 4 \times 3.0\ \text{cm}^2 = 12\ \text{cm}^2 = 1.2 \times 10^{-3}\ \text{m}^2

P=FA=1200 N1.2×10−3 m2=1.0×106 PaP = \frac{F}{A} = \frac{1200\ \text{N}}{1.2 \times 10^{-3}\ \text{m}^2} = 1.0 \times 10^{6}\ \text{Pa}

With pads: A=4×30 cm2=120 cm2=1.2×10−2 m2A = 4 \times 30\ \text{cm}^2 = 120\ \text{cm}^2 = 1.2 \times 10^{-2}\ \text{m}^2

P=1200 N1.2×10−2 m2=1.0×105 PaP = \frac{1200\ \text{N}}{1.2 \times 10^{-2}\ \text{m}^2} = 1.0 \times 10^{5}\ \text{Pa}

Ten times the area gives a tenth of the pressure, so the pads protect the floor tiles.

Worked numerical 2: a camel on sand

A camel of mass 480 kg stands on its four feet, and the pressure under them is 4.0 × 10⁴ Pa. Find the contact area of each foot. Take g=10 m s−2g = 10\ \text{m s}^{-2}.

Data: m=480 kgm = 480\ \text{kg}, P=4.0×104 PaP = 4.0 \times 10^{4}\ \text{Pa}, A=?A = ?

F=w=mg=480 kg×10 m s−2=4800 NF = w = mg = 480\ \text{kg} \times 10\ \text{m s}^{-2} = 4800\ \text{N} A=FP=4800 N4.0×104 N m−2=0.12 m2A = \frac{F}{P} = \frac{4800\ \text{N}}{4.0 \times 10^{4}\ \text{N m}^{-2}} = 0.12\ \text{m}^2

Each foot touches 0.12÷4=0.030 m20.12 \div 4 = 0.030\ \text{m}^2 of sand, which is 300 cm².

Exploring the block, nails and snowshoes

In the simulation above, a Brick of mass 2.0 kg lies flat on Dry sand. The cards show its weight, 20.0 N, the contact area, 0.0200 m² (200 cm²), and the pressure, 1000 Pa. The working uses g = 10 N kg⁻¹.

  1. Under the stage, press the Side face button, then End. The weight stays 20.0 N while the area drops to 100 cm² and then 50 cm², so the pressure climbs to 2000 Pa and then 4000 Pa. The sand keeps each dent.
  2. Press Flat and set Material to Steel. On the same 200 cm², the 79.0 N weight gives 3950 Pa: more force, more pressure.
  3. Under What to explore, choose Everyday examples, then pick Nails under the stage. A 20 N push on a balloon resting on one nail gives 1.00 × 10⁸ Pa, and the balloon bursts. Spread over 400 nails, the same push gives 2.50 × 10⁵ Pa, and the balloon holds.
  4. Pick Snowshoes. A walker's 650 N weight presses on soft snow with 10800 Pa through two boots but only 2170 Pa through snowshoes, which have five times the area.

Equations

  • Pressure

    Learn this

    P=FA

    pressure = force normal to a surface ÷ area of that surface

    Open calculator →

Common mistakes

  • Dividing an area in cm² by 100 to get m². There are 100 × 100 = 10 000 cm² in one square metre, so divide by 10 000; for mm², divide by 1 000 000.
  • Using a mass in kilograms as the force. Change the mass into a weight in newtons with w = mg = m × 10 before dividing by the area.
  • Dividing by the total surface area of the object rather than the contact area, which is only the part touching the ground or floor.
  • Using the area of only one leg, foot or tyre when several of them share the weight. Add up all the contact areas before dividing.
  • Treating force and pressure as one thing. The same force can give a tiny or an enormous pressure, depending on the area it acts on.
  • Writing the unit as N m or N m². Pressure is force ÷ area, so its unit is N m⁻², which is the pascal (Pa).

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.Pressure tells us how concentrated a force is on a surface.

    1. (a)Define pressure and write its formula.

      2 marks
      Show the answer

      Answer: Pressure is the normal (perpendicular) force per unit area of a surface: P = F/A.

      Marking points

      • Normal force per unit area
      • P = F/A
    2. (b)Name the SI unit of pressure and define it.

      2 marks
      Show the answer

      Answer: The pascal (Pa), equal to N m⁻². One pascal is the pressure when a force of 1 N acts normally on an area of 1 m².

      Marking points

      • Pascal (Pa) = N m⁻²
      • 1 N acting normally on an area of 1 m²
    3. (c)State two ways of increasing the pressure that a force exerts on a surface.

      2 marks
      Show the answer

      Answer: Increase the force, or decrease the contact area.

      Marking points

      • Increase the force
      • Decrease the contact area
    4. (d)Express a pressure of 3.5 kPa in N m⁻².

      1 mark
      Show the answer

      Answer: 3.5 × 1000 = 3500 N m⁻² (3.5 × 10³ Pa).

      Marking points

      • 3500 N m⁻²
  2. 2.A loaded truck has a total mass of 12 000 kg. It rests on 10 tyres, and each tyre touches the road over an area of 300 cm². Use g = 10 m s⁻².

    1. (a)Find the weight of the loaded truck.

      1 mark
      Show the answer

      Answer: w = mg = 12 000 kg × 10 m s⁻² = 1.2 × 10⁵ N.

      Marking points

      • 1.2 × 10⁵ N
    2. (b)Find the total area of contact with the road in m².

      2 marks
      Show the answer

      Answer: A = 10 × 300 cm² = 3000 cm². Dividing by 10 000 gives 0.30 m².

      Marking points

      • Total area = 3000 cm²
      • 3000 ÷ 10 000 = 0.30 m²
    3. (c)Calculate the pressure that the tyres exert on the road.

      2 marks
      Show the answer

      Answer: P = F/A = 1.2 × 10⁵ N ÷ 0.30 m² = 4.0 × 10⁵ Pa.

      Marking points

      • P = F/A = 1.2 × 10⁵ ÷ 0.30
      • 4.0 × 10⁵ Pa
    4. (d)The truck is overloaded until its total mass is 15 000 kg. The contact area does not change. Find the new pressure on the road.

      2 marks
      Show the answer

      Answer: The weight becomes 15 000 × 10 = 1.5 × 10⁵ N, so P = 1.5 × 10⁵ N ÷ 0.30 m² = 5.0 × 10⁵ Pa. For the same area, pressure rises in proportion to the force.

      Marking points

      • New weight = 1.5 × 10⁵ N
      • P = 1.5 × 10⁵ ÷ 0.30 = 5.0 × 10⁵ Pa
  3. 3.Use the idea of pressure to explain each of the following.

    1. (a)Camels can walk on soft desert sand without sinking far.

      2 marks
      Show the answer

      Answer: A camel's feet are broad and flat, so its weight acts over a large contact area. The pressure on the sand (P = F/A) is therefore small, and the sand can hold the camel up.

      Marking points

      • Broad feet give a large contact area
      • So the pressure on the sand is small and the camel does not sink far
    2. (b)An injection needle has a very fine point.

      2 marks
      Show the answer

      Answer: The fine point has a very small area, so even a gentle push produces a very large pressure, which is enough to pierce the skin.

      Marking points

      • Very small area at the point
      • A small force gives a very large pressure, so the needle pierces the skin
    3. (c)The foundation of a building is made wider than its walls.

      2 marks
      Show the answer

      Answer: A wide foundation spreads the building's weight over a large area of ground. This lowers the pressure on the soil, so the building does not sink into it.

      Marking points

      • Weight spread over a larger area
      • Lower pressure on the soil, so the building does not sink
  4. 4.In one mountain valley, the fresh snow can support a pressure of up to about 5.0 × 10³ Pa before a walker sinks in. A trekker of mass 60 kg stands on it in boots with a total contact area of 0.050 m². Use g = 10 m s⁻².

    1. (a)Calculate the pressure that the trekker exerts on the snow.

      3 marks
      Show the answer

      Answer: w = mg = 60 kg × 10 m s⁻² = 600 N. P = F/A = 600 N ÷ 0.050 m² = 1.2 × 10⁴ Pa.

      Marking points

      • w = mg = 60 × 10 = 600 N
      • P = F/A = 600 ÷ 0.050
      • 1.2 × 10⁴ Pa
    2. (b)Does the trekker sink into the snow? Give a reason.

      1 mark
      Show the answer

      Answer: Yes. The pressure, 1.2 × 10⁴ Pa, is more than the 5.0 × 10³ Pa that the snow can support.

      Marking points

      • Yes, because 1.2 × 10⁴ Pa is greater than 5.0 × 10³ Pa
    3. (c)Calculate the smallest total area of snowshoes that would stop the trekker sinking in.

      2 marks
      Show the answer

      Answer: A = F/P = 600 N ÷ 5.0 × 10³ Pa = 0.12 m².

      Marking points

      • A = F/P = 600 ÷ (5.0 × 10³)
      • 0.12 m²

Quick check

6 questions

  1. 1.The unit N m⁻² is also called the:
  2. 2.A force of 60 N acts at right angles to an area of 0.30 m². The pressure on the area is:
  3. 3.The force on a surface is doubled and the contact area is halved. The pressure becomes:
  4. 4.Which of these is designed to reduce pressure?
  5. 5.An area of 50 cm² is equal to:
  6. 6.A box of mass 8.0 kg rests on the floor on a face of area 0.040 m². Taking g = 10 m s⁻², the pressure it exerts is: