Skip to content

Punjab Board Class 9 Physics · Physical quantities and measurements

Precision and accuracy

Section 1.12

Precision is how closely repeated readings agree; your book also uses it for the fineness of an instrument's least count. Accuracy is closeness to the accepted (true) value and depends on the fractional uncertainty. Section 1.13: a final 5 is rounded so that an even digit is left.

Loading simulation…

Symbols match your course. Open the full accuracy, precision and errors simulation for more presets and teacher tools.

What section 1.12 asks

Precision and accuracy are separate ideas, and board papers often ask you to tell them apart. Section 1.13 then shows how to round off a result. How errors arise, and the uncertainty of a single reading (1.9 and 1.10), are on the Errors and uncertainty page.

Precision has two meanings

  1. Agreement within a set. Repeated measurements of one quantity are precise when they lie close to one another, like arrows grouped together on a target. This says nothing about where the group is.
  2. Fineness of the instrument. For a single measurement, your book says precision is set by the instrument. A screw gauge that reads to 0.01 mm gives a more precise result than Vernier Callipers reading to 0.1 mm, and both beat a metre rule that reads to 1 mm.

Accuracy

Accuracy describes how near a result comes to the accepted, or true, value. Your book links it to the fractional uncertainty, also called the relative uncertainty: what matters is the uncertainty compared with the size of the measurement.

fractional uncertainty=uncertaintymeasured value\text{fractional uncertainty} = \frac{\text{uncertainty}}{\text{measured value}}

Multiplying by 100 gives the percentage uncertainty. A smaller fraction means a more accurate result. So small objects need instruments with fine least counts, and a value with more significant figures counts as more accurate.

Worked numerical 1: one marble, three instruments

Each reading is uncertain by half its instrument's least count.

InstrumentReadingUncertaintyFractional uncertainty
Metre rule1.8 cm±0.05 cm0.05 ÷ 1.8 = 0.028 (2.8%)
Vernier Callipers1.84 cm±0.005 cm0.005 ÷ 1.84 = 0.0027 (0.27%)
Screw gauge18.42 mm±0.005 mm0.005 ÷ 18.42 = 0.00027 (0.027%)

The screw gauge's reading is the most precise, has the smallest fractional uncertainty and carries the most significant figures: four, against three and two. In your book's sense it is also the most accurate, as long as its zero error has been corrected.

Precise, accurate, both or neither

Arrows on the targetVerdictLikely cause
Grouped together, away from the bullseyePrecise, not accurateA systematic error, such as a zero error
Spread out, but centred on the bullseyeAccurate, not preciseLarge random errors
Grouped on the bullseyeAccurate and preciseOnly small errors
Spread out and off-centreNeitherBoth kinds of error

Your book's figure shows the first three cases; the fourth is an extra.

Worked numerical 2: rounding off (1.13)

Look at the first digit to be dropped:

  • more than 5, or a 5 followed by non-zero digits: add one to the last digit kept
  • less than 5: leave the last digit kept as it is
  • exactly 5, with nothing after it: add one if the digit before it is odd, but leave it if that digit is even, so the result ends in an even digit

Rounding to two significant figures:

3.65 m→3.6 m(6 is even)3.65\ \text{m} \rightarrow 3.6\ \text{m} \qquad (6 \text{ is even}) 2.75×103 kg→2.8×103 kg(7 is odd)2.75 \times 10^{3}\ \text{kg} \rightarrow 2.8 \times 10^{3}\ \text{kg} \qquad (7 \text{ is odd}) 5.851 s→5.9 s(more than halfway)5.851\ \text{s} \rightarrow 5.9\ \text{s} \qquad (\text{more than halfway})

Using the simulation

In the simulation above, steady hands have already put five shots on the bullseye of the Target view, labelled Accurate and precise, like the last picture in your book's figure.

  1. From the set-up menu next to Clear, choose Precise only, then Accurate only, then Neither. Each choice fires five fresh shots; compare the Accuracy and Precision gauges with the table above.
  2. Choose Resolution and press Measure. A steel ball 12.374 mm across gives 13 mm on the Metre rule, 12.6 mm on the Vernier Callipers and 12.57 mm on the Screw gauge, each labelled with its least count and ± half of it. The screw gauge is the most precise, yet every reading includes the +0.20 mm zero error: 12.57−0.20=12.3712.57 - 0.20 = 12.37 mm. Set the zero error slider to 0 to check.
  3. Choose Readings, then pick Stopwatch from the instrument menu: five times appear at once. Press Read 5 three times. The mean of the 20 times is exactly 1.605 s, and the Mean card shows 1.60 s, dropping the 5 after an even 0; its note says so.

Phone users will find the sliders under the Controls tab and the result cards under the Readings tab, beneath the stage.

Common mistakes

  • Writing that precise means accurate. A tight group of readings can all miss the true value, for example when the instrument has a zero error.
  • Giving only one meaning of precision. Your book uses the word both for agreement among repeated readings and for how fine an instrument's least count is.
  • Judging accuracy from the size of the uncertainty alone. Divide it by the measured value: ±0.05 cm is tiny on a 90 cm desk but large on a 0.5 cm bead.
  • Rounding every final 5 upwards. By section 1.13, a final 5 raises the digit before it only when that digit is odd; after an even digit it is simply dropped.
  • Using the 5 rule when more digits follow the 5. 2.851 is more than halfway between 2.8 and 2.9, so it rounds to 2.9 whatever the digit before it.

Exam-style questions

Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.

  1. 1.Precision and accuracy are two separate ideas in measurement.

    1. (a)Define precision and accuracy.

      2 marks
      Show the answer

      Answer: Precision: how closely repeated measurements of a quantity agree with one another. Accuracy: how near a measurement comes to the accepted (true) value.

      Marking points

      • Precision: how closely repeated measurements agree with one another
      • Accuracy: how near a measurement comes to the accepted (true) value
    2. (b)Arrows are shot at a target. Describe where the arrows land when the shooting is (i) precise but not accurate, (ii) accurate but not precise.

      2 marks
      Show the answer

      Answer: (i) Close together, but away from the bullseye. (ii) Spread out, but scattered evenly around the bullseye.

      Marking points

      • (i) Grouped close together, away from the bullseye
      • (ii) Spread out, but centred on the bullseye
    3. (c)According to your book, what decides the precision of a single measurement? Give an example.

      2 marks
      Show the answer

      Answer: The instrument used, through its least count. For example, a screw gauge, which reads to 0.01 mm, gives a more precise reading than a metre rule, which reads to 1 mm.

      Marking points

      • The instrument / its least count
      • Suitable example, e.g. a screw gauge reading (0.01 mm) is more precise than a metre rule reading (1 mm)
  2. 2.Vernier Callipers with a least count of 0.01 cm are used to measure the diameter of a cricket ball, 7.24 cm, and the thickness of a coin, 0.19 cm. Take the uncertainty of each reading as half the least count.

    1. (a)State the uncertainty in each reading.

      1 mark
      Show the answer

      Answer: ±0.005 cm

      Marking points

      • ±0.005 cm (half of 0.01 cm)
    2. (b)Calculate the fractional uncertainty of each measurement.

      2 marks
      Show the answer

      Answer: Ball: 0.005 ÷ 7.24 = 0.00069 (about 0.07%). Coin: 0.005 ÷ 0.19 = 0.026 (about 2.6%).

      Marking points

      • Ball: 0.005 ÷ 7.24 ≈ 0.0007
      • Coin: 0.005 ÷ 0.19 ≈ 0.026
    3. (c)Which measurement is more accurate? Give a reason.

      2 marks
      Show the answer

      Answer: The diameter of the ball, because its fractional uncertainty is much smaller. It also has more significant figures: three against two.

      Marking points

      • The cricket ball's diameter
      • Its fractional uncertainty is much smaller (about 0.0007 against 0.026)
    4. (d)Suggest a better instrument for measuring the thickness of the coin, and explain why it is better.

      2 marks
      Show the answer

      Answer: A screw gauge. Its least count, 0.01 mm, is ten times finer, so a reading such as 1.90 ± 0.005 mm has a fractional uncertainty of only about 0.003.

      Marking points

      • A screw gauge (micrometer)
      • Its least count (0.01 mm) is ten times finer, so the reading is more precise and its fractional uncertainty far smaller
  3. 3.Round off each value to three significant figures, using the rules in section 1.13 of your book.

    1. (a)6.245 m

      1 mark
      Show the answer

      Answer: 6.24 m: the final 5 follows an even digit (4), so it is dropped.

      Marking points

      • 6.24 m
    2. (b)1.375 × 10³ kg

      1 mark
      Show the answer

      Answer: 1.38 × 10³ kg: the final 5 follows an odd digit (7), so the 7 becomes 8.

      Marking points

      • 1.38 × 10³ kg
    3. (c)9.8651 s

      1 mark
      Show the answer

      Answer: 9.87 s: the part dropped, 0.0051, is more than half of 0.01, so round up.

      Marking points

      • 9.87 s
    4. (d)A student rounds 0.4565 m to 0.457 m. Is this correct by your book's rule? Explain.

      2 marks
      Show the answer

      Answer: No. The dropped digit is exactly 5 and the digit before it, 6, is even, so the 6 stays: 0.456 m.

      Marking points

      • No: it should be 0.456 m
      • The dropped digit is exactly 5 and the 6 before it is even, so it is left unchanged
  4. 4.A student measures the diameter of a steel ball four times with a screw gauge and gets 12.57 mm each time. The accepted value of the diameter is 12.37 mm.

    1. (a)Are the readings precise? Give a reason.

      2 marks
      Show the answer

      Answer: Yes. All four readings agree exactly, and they were taken with an instrument whose least count is only 0.01 mm.

      Marking points

      • Yes
      • The four readings agree with one another (all 12.57 mm), taken with a fine least count of 0.01 mm
    2. (b)Are the readings accurate? Give a reason.

      2 marks
      Show the answer

      Answer: No. Each reading is 0.20 mm larger than the accepted value.

      Marking points

      • No
      • Each is 0.20 mm above the accepted value of 12.37 mm
    3. (c)Suggest the cause of this error and how the readings should be corrected.

      2 marks
      Show the answer

      Answer: A zero error of +0.20 mm in the screw gauge, which is a systematic error. Subtract it from each reading: 12.57 mm − 0.20 mm = 12.37 mm.

      Marking points

      • A zero error of +0.20 mm (a systematic error)
      • Subtract it from each reading: 12.57 mm − 0.20 mm = 12.37 mm

Quick check

6 questions

  1. 1.Arrows land close to one another but far from the bullseye. The shooting is:
  2. 2.In your book's sense, which least count gives the most precise single reading?
  3. 3.A length is recorded as 25.0 cm ± 0.05 cm. What is its fractional uncertainty?
  4. 4.Using the rule in section 1.13, what is 3.85 × 10² m rounded to two significant figures?
  5. 5.According to your book, the accuracy of a measurement depends on its:
  6. 6.Accuracy describes how near a measurement comes to: