Skip to content

BISE Gujranwala · Punjab Class 9

BISE Gujranwala Annual 2023 Class 9 Physics (Subjective, Group I)

Set by BISE Gujranwala for Punjab Class 9 Physics, Annual 2023: 1 hour 45 minutes and 48 marks, on Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science. The paper itself is on BISE Gujranwala’s website; this page adds what it covers, how to use it and original practice questions on the same topics.

Paper facts

Series
Annual 2023
Paper
Subjective, Group I
Set by
BISE Gujranwala
Tier
Not tiered
Time
1 hour 45 minutes
Marks
48
Calculator
Not recorded here: check the paper’s instructions
Syllabus
Old Punjab syllabus (PCTB Physics 9 used until the 2024-25 session), not the NC 2023 book. Some questions, such as satellites and heat transfer, are not in the new course.
Links checked
17 November 2026

Official files

These files belong to BISE Gujranwala. Labverse links to them and never hosts or copies them. Labverse is not affiliated with BISE Gujranwala.

What this paper covers

8 topic groups from our map of Punjab Board Class 9 Physics. Revise each one with its topic pages and simulations before you sit the paper.

How to use this paper

  1. 1. Time it. Set 1 hour 45 minutes for 48 marks: about 131 seconds a mark. At 53 minutes you should be roughly halfway through the marks; if you’re well behind, speed up on the short questions.
  2. 2. Sit it in one go. Open the question paper on BISE Gujranwala’s website (the link above) and work on paper, with no notes.
  3. 3. Mark it with the official scheme. The mark scheme isn’t public, so check answers with your teacher, and use the marking points on our questions below to practise marking.
  4. 4. Learn from the marks you lost. For every lost mark, note whether it was knowledge, method, reading the question or time.
  5. 5. Log mistakes by topic. Keep one line per topic group (Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science) and add a tally each time a mark goes there.
  6. 6. Revisit, then redo. Work through the weakest group’s topic pages and simulations, try the questions below, and come back to the paper in a week.

Practise the same topics

7 original exam-style questions on this paper’s topics, written in the style of Punjab board exams (not taken from the paper). Try each one before you reveal the answer.

  1. 1.The SI is built on seven base quantities.

    From the topic: Physical quantities and SI units

    1. (a)How is a derived quantity different from a base quantity?

      2 marks
      Show the answer

      Answer: Base quantities are the few quantities chosen as the foundation, not defined from any others. Derived quantities are defined from base quantities by multiplying or dividing them.

      Marking points

      • Base quantities: the chosen basic quantities, not defined in terms of others
      • Derived quantities: defined from one or more base quantities (e.g. speed from distance and time)
    2. (b)Write the SI unit, with its symbol, of each base quantity: (i) mass (ii) temperature (iii) electric current (iv) amount of substance.

      4 marks
      Show the answer

      Answer: (i) kilogram, kg (ii) kelvin, K (iii) ampere, A (iv) mole, mol

      Marking points

      • kilogram, kg
      • kelvin, K
      • ampere, A
      • mole, mol
  2. 2.Vernier Callipers are used in the laboratory to measure small lengths. The main scale is marked in millimetres, and 10 Vernier divisions cover 9 mm.

    From the topic: Vernier callipers

    1. (a)Define least count.

      1 mark
      Show the answer

      Answer: The least count is the smallest length that an instrument can measure reliably.

      Marking points

      • Smallest length the instrument can measure reliably
    2. (b)Show that the least count of these Vernier Callipers is 0.01 cm.

      2 marks
      Show the answer

      Answer: One Vernier division = 9 mm ÷ 10 = 0.9 mm. Least count = 1 M.S. division − 1 V.S. division = 1 mm − 0.9 mm = 0.1 mm = 0.01 cm.

      Marking points

      • 1 V.S. division = 9 mm ÷ 10 = 0.9 mm
      • L.C. = 1 mm − 0.9 mm = 0.1 mm = 0.01 cm
    3. (c)Name the part of the Vernier Callipers you would use to measure (i) the inside diameter of a steel cup, (ii) the depth of a hole drilled in a wooden block.

      2 marks
      Show the answer

      Answer: (i) The inside jaws. (ii) The tail (depth gauge).

      Marking points

      • Inside jaws
      • Tail / depth gauge
  3. 3.Answer these short questions on scalar and vector quantities.

    From the topic: Scalars and vectors

    1. (a)Define the terms scalar and vector.

      2 marks
      Show the answer

      Answer: A scalar is a physical quantity that is fully specified by its magnitude alone (a number with a unit). A vector is a physical quantity that is fully specified only when its direction is given as well as its magnitude.

      Marking points

      • Scalar: fully specified by magnitude alone (number with unit)
      • Vector: needs magnitude and direction
    2. (b)Sort these into scalars and vectors: time, velocity, energy, weight, temperature, displacement.

      3 marks
      Show the answer

      Answer: Scalars: time, energy, temperature. Vectors: velocity, weight, displacement.

      Marking points

      • Any two items correctly sorted
      • Any four items correctly sorted
      • All six correct: scalars time, energy, temperature; vectors velocity, weight, displacement
    3. (c)A vector cannot be written in bold by hand. How is a vector shown in a handwritten answer, and how is its magnitude shown?

      2 marks
      Show the answer

      Answer: The vector is written as its letter with a small arrow over it, e.g. F with an arrow. Its magnitude is the plain (italic) letter with no arrow, e.g. F.

      Marking points

      • Vector: letter with an arrow drawn over it
      • Magnitude: the plain letter without the arrow
  4. 4.A toy cannon of mass 2 kg rests on a smooth floor. It fires a ball of mass 0.05 kg horizontally at 20 m s⁻¹.

    From the topic: Conservation of momentum

    1. (a)Calculate the recoil velocity of the cannon.

      3 marks
      Show the answer

      Answer: Total momentum before = 0. After: 0 = (0.05)(20) + (2)v, so v = −1 ÷ 2 = −0.5 m s⁻¹.

      Marking points

      • Total momentum before firing is zero
      • 0 = 0.05 × 20 + 2v
      • v = −0.5 m s⁻¹ (0.5 m s⁻¹)
    2. (b)What does the negative sign in your answer show?

      1 mark
      Show the answer

      Answer: The cannon moves in the opposite direction to the ball (backwards).

      Marking points

      • Cannon moves opposite to the ball
  5. 5.Two forces of 6 N and 8 N act on a point at right angles to each other.

    From the topic: Parallel forces and addition of forces

    1. (a)Describe how to find their resultant by the head-to-tail rule.

      3 marks
      Show the answer

      Answer: Choose a suitable scale, such as 1 cm for 2 N. Draw the 8 N force to scale, then draw the 6 N force starting from the head of the first, at right angles to it. Join the tail of the first force to the head of the second; this line is the resultant. Measure its length and angle and convert with the scale.

      Marking points

      • Suitable scale chosen; first force drawn to scale
      • Tail of the second force placed at the head of the first
      • Resultant drawn from the tail of the first to the head of the last, then measured
    2. (b)Using a scale of 1 cm for 2 N, the resultant measures 5.0 cm. State the size of the resultant force.

      1 mark
      Show the answer

      Answer: 5.0 × 2 = 10 N.

      Marking points

      • 10 N
  6. 6.Energy can be stored as potential energy.

    From the topic: Potential energy

    1. (a)Define potential energy.

      1 mark
      Show the answer

      Answer: Potential energy is the energy stored in a body because of its position or its deformation (change of shape).

      Marking points

      • Energy due to position or deformation
    2. (b)Name two forms of potential energy and give one example of each.

      2 marks
      Show the answer

      Answer: Any two, e.g. gravitational potential energy (water stored behind a dam); elastic potential energy (a compressed spring or stretched catapult rubber); chemical potential energy (petrol or the chemicals in a battery).

      Marking points

      • First form with a matching example
      • Second form with a matching example
    3. (c)A body of mass m is lifted at a constant velocity through a height h. Show that its gravitational potential energy is Ep = mgh.

      3 marks
      Show the answer

      Answer: At constant velocity there is no acceleration, so the upward force equals the weight, w = mg. Work done = force × distance = mg × h. This work is stored in the body as gravitational potential energy, so Ep = mgh.

      Marking points

      • Constant velocity, so lifting force = weight = mg
      • Work done = mg × h
      • Work done is stored as Ep, so Ep = mgh
  7. 7.In one mountain valley, the fresh snow can support a pressure of up to about 5.0 × 10³ Pa before a walker sinks in. A trekker of mass 60 kg stands on it in boots with a total contact area of 0.050 m². Use g = 10 m s⁻².

    From the topic: Pressure

    1. (a)Calculate the pressure that the trekker exerts on the snow.

      3 marks
      Show the answer

      Answer: w = mg = 60 kg × 10 m s⁻² = 600 N. P = F/A = 600 N ÷ 0.050 m² = 1.2 × 10⁴ Pa.

      Marking points

      • w = mg = 60 × 10 = 600 N
      • P = F/A = 600 ÷ 0.050
      • 1.2 × 10⁴ Pa
    2. (b)Does the trekker sink into the snow? Give a reason.

      1 mark
      Show the answer

      Answer: Yes. The pressure, 1.2 × 10⁴ Pa, is more than the 5.0 × 10³ Pa that the snow can support.

      Marking points

      • Yes, because 1.2 × 10⁴ Pa is greater than 5.0 × 10³ Pa
    3. (c)Calculate the smallest total area of snowshoes that would stop the trekker sinking in.

      2 marks
      Show the answer

      Answer: A = F/P = 600 N ÷ 5.0 × 10³ Pa = 0.12 m².

      Marking points

      • A = F/P = 600 ÷ (5.0 × 10³)
      • 0.12 m²