AQA · GCSE AQA
AQA GCSE Physics June 2023 Paper 1 Higher (8463/1H)
Set by AQA for AQA GCSE Physics, June 2023: 1 hour 45 minutes and 100 marks, on Energy, Electricity, Particle model of matter, Atomic structure, Working scientifically. The paper itself is on AQA’s website; this page adds what it covers, how to use it and original practice questions on the same topics.
Paper facts
- Series
- June 2023
- Paper
- Paper 1 Higher
- Code
- 8463/1H
- Tier
- Higher
- Time
- 1 hour 45 minutes
- Marks
- 100
- Calculator
- Allowed
- Syllabus
- 8463 (first teaching 2016)
- Links checked
- 17 November 2026
Official files
- Question paper(opens AQA’s website)
- Mark scheme(opens AQA’s website)
- Examiner report(opens AQA’s website)
These files belong to AQA. Labverse links to them and never hosts or copies them. Labverse is not affiliated with AQA.
What this paper covers
5 topic groups from our map of GCSE Physics — AQA. Revise each one with its topic pages and simulations before you sit the paper.
- Energy
Energy stores and systems · Kinetic and potential energy · Specific heat capacity · Power · Conservation and dissipation of energy · Efficiency · Energy resources
Energy stores and transfersEnergy skate trackSpecific heat capacityPower and efficiency
- Electricity
Circuit symbols · Electrical charge and current · Current, resistance and potential difference · I–V characteristics · LDRs and thermistors · Series and parallel circuits · Mains electricity · Electrical power · Energy transfers in appliances · The National Grid · Static electricity and electric fields
Circuit builderCharge, current, energy and powerResistance of a wireI–V characteristics
- Particle model of matter
Density · Changes of state · Internal energy · Specific latent heat · Particle motion in gases · Pressure in gases
Measuring densityParticle model and states of matterLatent heat and heating curvesGas laws and particles
- Atomic structure
Structure of the atom · Mass number and isotopes · Development of the atomic model · Radioactive decay and nuclear radiation · Nuclear equations · Half-life · Contamination and irradiation · Uses and hazards of radiation · Nuclear fission and fusion
Isotopes and atom builderAtomic models and Rutherford scatteringAlpha, beta and gamma radiationNuclear equations
- Working scientifically
Measuring instruments · Accuracy, precision and errors · Units, prefixes and significant figures
Vernier caliperMicrometer screw gaugeAccuracy, precision and errorsSignificant figures, prefixes and units trainer
How to use this paper
- 1. Time it. Set 1 hour 45 minutes for 100 marks: about 63 seconds a mark. At 53 minutes you should be roughly halfway through the marks; if you’re well behind, speed up on the short questions.
- 2. Sit it in one go. Open the question paper on AQA’s website (the link above) and work on paper, with no notes.
- 3. Mark it with the official scheme. Give a mark only when your answer matches a marking point. Be strict with yourself: it’s the gaps you find that improve your grade.
- 4. Read the examiner report. It says which questions students found hardest and what the best answers did, so compare it with your own script.
- 5. Log mistakes by topic. Keep one line per topic group (Energy, Electricity, Particle model of matter, Atomic structure, Working scientifically) and add a tally each time a mark goes there.
- 6. Revisit, then redo. Work through the weakest group’s topic pages and simulations, try the questions below, and come back to the paper in a week.
Practise the same topics
8 original exam-style questions on this paper’s topics, written in the style of GCSE AQA (not taken from the paper). Try each one before you reveal the answer.
1.A delivery van of mass 2000 kg travels along a straight road at 12 m/s.
From the topic: Kinetic and potential energy
(a)Write down the equation that links kinetic energy, mass and speed.
1 markShow the answerHide the answer
Answer: kinetic energy = 0.5 × mass × (speed)² (Ek = ½ m v²)
Marking points
- kinetic energy = 0.5 × mass × (speed)²
(b)Calculate the kinetic energy of the van.
2 marksShow the answerHide the answer
Answer: Ek = 0.5 × 2000 × 12² = 144 000 J
Marking points
- Ek = 0.5 × 2000 × 12²
- Ek = 144 000 J
(c)The van speeds up to 24 m/s. A student says its kinetic energy will double. Explain why the student is wrong.
2 marksShow the answerHide the answer
Answer: Kinetic energy depends on the speed squared. Doubling the speed multiplies the kinetic energy by 2² = 4, giving 576 000 J, not 288 000 J.
Marking points
- Kinetic energy is proportional to the speed squared.
- So doubling the speed makes the kinetic energy four times as big (576 000 J).
(d)The van brakes to a stop. Name the store that most of its kinetic energy is transferred to.
1 markShow the answerHide the answer
Answer: The thermal store of the brakes (and the surroundings).
Marking points
- Thermal (energy) store of the brakes / surroundings
2.An electric drill becomes warm and noisy when it is used for a long time.
From the topic: Conservation and dissipation of energy
(a)State the principle of conservation of energy.
1 markShow the answerHide the answer
Answer: Energy can never be created or destroyed, so the total stays the same; it can only move between stores or spread out.
Marking points
- Energy cannot be created or destroyed.
(b)Explain why the energy that warms the drill is described as wasted.
2 marksShow the answerHide the answer
Answer: It goes into the thermal stores of the drill and the surrounding air, which is not the job the drill is for. It spreads out, so it cannot easily be used again.
Marking points
- It is transferred to thermal stores of the drill and the surroundings, not to the intended (useful) store.
- It is spread out (dissipated), so it cannot easily be used.
(c)Explain how oiling the gears inside the drill reduces the wasted energy.
2 marksShow the answerHide the answer
Answer: Oil lubricates the gears, which reduces the friction between them. Less work is done against friction, so less energy is dissipated by heating.
Marking points
- Lubrication reduces friction between the moving gears.
- So less energy is transferred by heating (dissipated) to thermal stores.
3.A garden light uses an LDR connected in series with a 10 kΩ fixed resistor across a 12 V supply. An electronic switch turns the light on when the p.d. across the LDR is high enough.
From the topic: LDRs and thermistors
(a)Explain why the p.d. across the LDR increases as it gets dark.
3 marksShow the answerHide the answer
Answer: In the dark the LDR's resistance increases. In series the supply p.d. is shared, and the component with the larger resistance takes the larger share. So the p.d. across the LDR increases.
Marking points
- Resistance of the LDR increases as light intensity falls.
- The supply p.d. is shared between the two components in series.
- The LDR now has a larger share of the p.d. (because its share of the total resistance is larger).
(b)At night the resistance of the LDR is 50 kΩ. Calculate the p.d. across the LDR.
3 marksShow the answerHide the answer
Answer: Total resistance = 50 kΩ + 10 kΩ = 60 000 Ω. Current = 12 ÷ 60 000 = 0.00020 A. P.d. across LDR = 0.00020 × 50 000 = 10 V
Marking points
- Total resistance = 60 000 Ω
- Current = 0.00020 A
- P.d. across the LDR = 10 V
4.A 20 Ω resistor and a 30 Ω resistor are connected in series with a 12 V battery.
From the topic: Series and parallel circuits
(a)Calculate the total resistance of the circuit.
1 markShow the answerHide the answer
Answer: R total = 20 + 30 = 50 Ω
Marking points
- 50 Ω
(b)Calculate the current in the circuit.
2 marksShow the answerHide the answer
Answer: I = V ÷ R = 12 ÷ 50 = 0.24 A
Marking points
- I = 12 ÷ 50
- I = 0.24 A
(c)Calculate the potential difference across the 30 Ω resistor.
2 marksShow the answerHide the answer
Answer: V = I R = 0.24 × 30 = 7.2 V
Marking points
- V = 0.24 × 30 (allow their current from the previous part)
- V = 7.2 V
5.A student heats a solid substance in a boiling tube with a small electric heater. The heater transfers energy at a steady rate of 25 W. The temperature of the substance rises from 20 °C to 44 °C, stays at 44 °C for 5.0 minutes, then starts to rise again.
From the topic: Internal energy
(a)State the melting point of the substance.
1 markShow the answerHide the answer
Answer: 44 °C
Marking points
- 44 °C
(b)Calculate the energy transferred by the heater during the 5.0 minutes that the temperature stays at 44 °C.
3 marksShow the answerHide the answer
Answer: t = 5.0 × 60 = 300 s. E = P t = 25 × 300 = 7500 J
Marking points
- t = 300 s
- E = 25 × 300
- E = 7500 J
(c)The internal energy of the substance increases by less than your answer to the previous part. Suggest one reason why.
1 markShow the answerHide the answer
Answer: Some of the energy from the heater is transferred to the surroundings, such as the air and the boiling tube, instead of to the substance.
Marking points
- Some energy is transferred to the surroundings (air, boiling tube or heater) rather than to the substance.
(d)Describe how the kinetic and potential energies of the particles change while the temperature stays at 44 °C.
2 marksShow the answerHide the answer
Answer: The particles’ average kinetic energy is unchanged. Their potential energy increases as the solid melts.
Marking points
- Average kinetic energy of the particles: no change.
- Potential energy of the particles: increases.
6.Steam at 100 °C from a kettle condenses on a person's hand. Specific latent heat of vaporisation of water = 2.26 × 10⁶ J/kg. Specific heat capacity of water = 4200 J/kg °C.
From the topic: Specific latent heat
(a)Name the change of state when steam turns into water.
1 markShow the answerHide the answer
Answer: Condensing (condensation)
Marking points
- Condensing / condensation
(b)Calculate the energy released when 2.0 g of steam at 100 °C condenses to water at 100 °C.
3 marksShow the answerHide the answer
Answer: m = 2.0 g = 0.0020 kg. E = m L = 0.0020 × 2.26 × 10⁶ = 4520 J
Marking points
- m = 0.0020 kg
- E = 0.0020 × 2.26 × 10⁶
- E = 4520 J (accept 4500 J)
(c)The water then cools from 100 °C to 35 °C on the skin. Calculate the energy released as it cools.
2 marksShow the answerHide the answer
Answer: ΔE = m c Δθ = 0.0020 × 4200 × 65 = 546 J
Marking points
- ΔE = 0.0020 × 4200 × 65
- ΔE = 546 J (accept 550 J)
(d)Use your answers to explain why a scald from steam at 100 °C is much worse than one from the same mass of water at 100 °C.
2 marksShow the answerHide the answer
Answer: Water at 100 °C only releases the 546 J as it cools. Steam releases 4520 J of latent heat as it condenses, as well as the 546 J, so it transfers over nine times as much energy to the skin.
Marking points
- Steam releases latent heat (4520 J) when it condenses, in addition to the energy released as the water cools.
- So much more energy (about nine times as much in total) is transferred to the skin.
7.A calcium atom, ⁴⁰₂₀Ca, loses its two outer electrons.
From the topic: Mass number and isotopes
(a)Give the numbers of protons, neutrons and electrons in the particle that is formed.
3 marksShow the answerHide the answer
Answer: 20 protons, 40 − 20 = 20 neutrons and 20 − 2 = 18 electrons.
Marking points
- 20 protons
- 20 neutrons
- 18 electrons
(b)Name this type of particle and state its charge.
2 marksShow the answerHide the answer
Answer: A positive ion, with a charge of 2+ (+2).
Marking points
- (Positive) ion
- Charge of 2+ / +2
(c)Explain why the mass number of the particle is still 40.
2 marksShow the answerHide the answer
Answer: The mass number counts only protons and neutrons. Neither of these changed, because only electrons were lost.
Marking points
- Mass number = number of protons + number of neutrons (electrons not included)
- The numbers of protons and neutrons have not changed; only electrons were lost
8.Scientists' ideas about atoms have changed over time. In the early 1900s, the plum pudding model was the accepted model of the atom.
From the topic: Development of the atomic model
(a)Describe the plum pudding model of the atom.
2 marksShow the answerHide the answer
Answer: Positive charge fills the whole atom, and negative electrons are dotted through it.
Marking points
- A ball (sphere) of positive charge filling the whole atom
- With negative electrons scattered through it (allow: embedded in it)
(b)Name the discovery that led to the plum pudding model.
1 markShow the answerHide the answer
Answer: The discovery of the electron.
Marking points
- (Discovery of) the electron
(c)Explain why this discovery showed that atoms are not the smallest particles of matter.
2 marksShow the answerHide the answer
Answer: Electrons are particles much smaller than atoms that come from inside them. So atoms must contain smaller particles and can be split into parts.
Marking points
- Electrons are (much) smaller than atoms / come from inside atoms
- So atoms have smaller parts / are not indivisible
(d)Give two differences between the plum pudding model and the nuclear model.
2 marksShow the answerHide the answer
Answer: Any two from: in the nuclear model the positive charge is concentrated in a nucleus at the centre, not spread out; nearly all the mass is in the nucleus, not spread out; most of the nuclear atom is empty space; the electrons are outside the nucleus instead of mixed through the positive charge.
Marking points
- First difference, e.g. positive charge concentrated in a central nucleus (not spread out)
- Second difference, e.g. mass concentrated in the nucleus / atom mostly empty space / electrons outside the nucleus