What AQA asks for: spec point 4.3.1.2
This part of the particle model is for every AQA student: both tiers, Combined Science and GCSE Physics. It has no equation, but density questions often build on it. You should be able to:
- name the six changes on AQA's list, with the state each starts and ends in
- describe why mass is conserved when a substance changes state
- explain why a change of state is a physical change, not a chemical one
Six changes between three states
| Change | From | To | Everyday example |
|---|---|---|---|
| Melting | solid | liquid | an ice lolly dripping in the sun |
| Freezing | liquid | solid | water setting in an ice-cube tray |
| Boiling | liquid | gas | a pan bubbling hard on the hob |
| Evaporating | liquid | gas | wet washing drying on a line |
| Condensing | gas | liquid | a bathroom mirror misting up |
| Sublimating | solid | gas | dry ice (solid carbon dioxide) vanishing without a puddle |
Boiling and evaporating both turn liquid into gas. Evaporation happens only at the surface, and it can happen well below the boiling point. Boiling happens throughout the liquid, with bubbles of vapour forming inside it, and only at the boiling point. Water boils at 100 °C at standard atmospheric pressure; where the air pressure is lower, its boiling point is lower too.
Why the mass does not change
No particles are made or destroyed when a substance changes state. The same atoms or molecules are still there. Only their arrangement, their spacing and their motion are different, so the mass stays the same.
The volume usually does change. Gas particles are far more spread out than liquid ones, so a gas fills much more space. Since density is mass ÷ volume, the same mass in a new volume has a new density.
An open container can look like an exception. As water evaporates from a beaker on a balance, the reading falls, but no mass is destroyed: water particles have simply left the beaker for the air.
Worked example: a bottle in the freezer. A glass bottle holds 0.75 kg of water and is left in a freezer. Water has a density of 1000 kg/m³ and ice about 920 kg/m³. How much more room does the ice need?
Given: the mass is still 0.75 kg after freezing. Equation: recall , so . Water: m³ (750 cm³). Ice: m³ (815 cm³). Answer: about 65 cm³ more, enough to crack the glass. Water is unusual: most substances shrink slightly as they freeze.
Worked explanation: ice in a sealed bag. A sealed bag of ice cubes reads 46.3 g on a balance. An hour later the ice has melted, and the reading is still 46.3 g. Melting only rearranged the particles, and nothing entered or left the bag. Droplets on the outside of the cold bag are condensed water vapour from the room, so wipe them off before weighing.
Physical, not chemical
A change of state is a physical change. No new substance forms, and reversing the change gives back the original material with all of its properties. Refreeze meltwater and you have ice again.
A chemical change makes new substances, and cooling them does not bring back the starting material. A burning candle shows both. Wax near the wick melts, and that liquid sets back into wax when it cools. Some of it turns to vapour, which burns to form carbon dioxide and water. Cooling those will never give you wax.
Using the simulation
In the simulation above, Heating curve begins with 0.50 kg of crushed ice at −20 °C and the heater already set to Heater on. Press Play and the Stage card steps through Ice warms, Ice melts, Water warms, Water boils and Steam warms.
During melting, the Changed state card counts up (for example, 0.25 of 0.50 kg melted) and the particle window reads Pattern breaking up. The total stays 0.50 kg throughout, because the model's container keeps the steam in (see About the model); an open pan would lose mass as steam escaped.
Now choose Cooling curve and press Play. Liquid stearic acid cools until the Stage card reads Freezes, and the graph stays flat at about 69 °C: freezing need not be cold. The solid formed is still stearic acid.