Skip to content

GCSE Physics — AQA · Electricity

LDRs and thermistors

4.2.1.4

Thermistors and LDRs are sensors: warming a thermistor, or shining more light on an LDR, lowers its resistance. You need to explain uses such as a thermostat and lights that come on at dusk.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

Sensors in the AQA specification

Thermistors and LDRs are part of spec point 4.2.1.4, on both tiers. They are resistors whose resistance is not fixed: it depends on their surroundings. That makes them ideal sensors. AQA expects you to describe how each one behaves, read their graphs, and explain one everyday use of each.

There is no new equation for this topic. You use V=IRV = IR from spec point 4.2.1.3, which you must remember, to work out a resistance from meter readings.

The thermistor: a temperature sensor

As a thermistor gets warmer, its resistance goes down. As it cools, its resistance goes up.

A graph of resistance against temperature is a curve, not a straight line. The resistance falls steeply at low temperatures, then more gently as the thermistor warms further.

AQA asks you to know how thermistors are used in circuits, with a thermostat as the main example. In a home heating system, a thermistor senses the room temperature. When the room cools, the thermistor's resistance rises, and the circuit uses that change to switch the boiler on. Fridges, ovens, car engines and digital thermometers use the same idea.

The LDR: a light sensor

LDR stands for light-dependent resistor. In bright light its resistance is low. In darkness its resistance becomes very high, often more than 100 000 Ω.

Its graph is also a curve: resistance drops as the light intensity rises, quickly at first and then more slowly.

The use AQA highlights is switching lights on automatically when it gets dark. Street lamps in Manchester, solar garden lights in Lagos and porch lights in Toronto can all work this way.

How a sensing circuit uses the change

A sensor is usually placed in series with a fixed resistor across a supply. In a series circuit the supply p.d. is shared, and the component with more resistance takes the bigger share.

Picture an LDR in series with a fixed resistor at dusk:

  1. The light fades, so the LDR's resistance rises.
  2. The LDR now takes a larger share of the supply p.d.
  3. The p.d. across the LDR grows until it is big enough to trigger a switch that turns the lamp on.

Swap the LDR for a thermistor and the same circuit responds to temperature instead.

Worked example: a thermistor at two temperatures

A thermistor is connected to a 6.0 V supply. At 20 °C the current is 2.0 mA. At 60 °C the current is 7.5 mA. Find the resistance at each temperature.

Given: V=6.0 VV = 6.0\ \text{V}, I1=2.0 mA=0.0020 AI_1 = 2.0\ \text{mA} = 0.0020\ \text{A}, I2=7.5 mA=0.0075 AI_2 = 7.5\ \text{mA} = 0.0075\ \text{A}

Equation: V=IRV = IR, so R=VIR = \dfrac{V}{I}

Substitution: R1=6.00.0020R_1 = \dfrac{6.0}{0.0020} and R2=6.00.0075R_2 = \dfrac{6.0}{0.0075}

Answer: R1=3000 ΩR_1 = 3000\ \Omega (3.0 kΩ) and R2=800 ΩR_2 = 800\ \Omega

The resistance has fallen as the temperature rose, which is just what a thermistor should do.

Investigating the sensors

AQA suggests two investigations here. They are not among the ten required practicals, but they are good exam material.

  • Thermistor: put the thermistor in a beaker of water with a thermometer. Heat the water in steps, stir, and record the current and p.d. at each temperature. Calculate R=VIR = \dfrac{V}{I} each time.
  • LDR: shine a lamp on the LDR from different distances in a darkened room, or measure the light level with a light meter. Record the current and p.d. at each light level.

Using the simulation

In the simulation above, choose LDR divider. The voltmeter reads the p.d. across the LDR. Drag the light level slider down and watch that reading climb as the LDR takes a larger share of the p.d. Take the slider close to 0% to model night-time: the reading gets close to the full 6 V of the battery, because the LDR now has far more resistance than the fixed resistor. Finally, choose Empty, build a loop with the battery, a thermistor and an ammeter, move the temperature slider from cold to hot, and watch the current rise as the thermistor's resistance falls.

Common mistakes

  • Saying a thermistor's resistance increases as it gets hotter; for AQA it decreases.
  • Saying an LDR has a low resistance in the dark; its resistance is highest in the dark.
  • Drawing the resistance–temperature graph of a thermistor as a straight line instead of a curve.
  • Explaining a sensing circuit only in terms of resistance without saying how the current or the share of the p.d. changes.
  • Mixing up the uses: thermistors sense temperature (thermostats), LDRs sense light (automatic lights).
  • Forgetting to convert milliamps to amps when calculating a sensor's resistance with R = V ÷ I.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A thermistor is used to control the heater in a tropical fish tank.

    1. (a)Describe how the resistance of the thermistor changes as the temperature of the water increases.

      1 mark
      Show the answer

      Answer: The resistance decreases.

      Marking points

      • Resistance decreases as temperature increases.
    2. (b)The potential difference across the thermistor is 4.0 V and the current through it is 0.0020 A. Calculate its resistance.

      2 marks
      Show the answer

      Answer: R = V ÷ I = 4.0 ÷ 0.0020 = 2000 Ω

      Marking points

      • R = 4.0 ÷ 0.0020
      • R = 2000 Ω (accept 2.0 kΩ)
    3. (c)The water cools down. The potential difference across the thermistor stays the same. Explain what happens to the current in the thermistor.

      2 marks
      Show the answer

      Answer: As the water cools, the thermistor's resistance increases. With the same p.d., a larger resistance means the current decreases.

      Marking points

      • Resistance of the thermistor increases.
      • So the current decreases (for the same p.d.).
  2. 2.A student investigates how the resistance of an LDR changes with light intensity. A lamp is placed at different distances from the LDR in a darkened room.

    1. (a)Give the independent variable in this investigation.

      1 mark
      Show the answer

      Answer: The light intensity (controlled by the distance of the lamp from the LDR).

      Marking points

      • Light intensity (accept distance between lamp and LDR).
    2. (b)Describe how an ammeter and a voltmeter should be connected to find the resistance of the LDR.

      2 marks
      Show the answer

      Answer: The ammeter is connected in series with the LDR. The voltmeter is connected in parallel across the LDR.

      Marking points

      • Ammeter in series with the LDR.
      • Voltmeter in parallel across the LDR.
    3. (c)Describe the result the student should expect as the lamp is moved closer to the LDR.

      1 mark
      Show the answer

      Answer: The light intensity increases, so the resistance of the LDR decreases.

      Marking points

      • Resistance of the LDR decreases (as light intensity increases).
  3. 3.A garden light uses an LDR connected in series with a 10 kΩ fixed resistor across a 12 V supply. An electronic switch turns the light on when the p.d. across the LDR is high enough.

    1. (a)Explain why the p.d. across the LDR increases as it gets dark.

      3 marks
      Show the answer

      Answer: In the dark the LDR's resistance increases. In series the supply p.d. is shared, and the component with the larger resistance takes the larger share. So the p.d. across the LDR increases.

      Marking points

      • Resistance of the LDR increases as light intensity falls.
      • The supply p.d. is shared between the two components in series.
      • The LDR now has a larger share of the p.d. (because its share of the total resistance is larger).
    2. (b)At night the resistance of the LDR is 50 kΩ. Calculate the p.d. across the LDR.

      3 marks
      Show the answer

      Answer: Total resistance = 50 kΩ + 10 kΩ = 60 000 Ω. Current = 12 ÷ 60 000 = 0.00020 A. P.d. across LDR = 0.00020 × 50 000 = 10 V

      Marking points

      • Total resistance = 60 000 Ω
      • Current = 0.00020 A
      • P.d. across the LDR = 10 V

Quick check

6 questions

  1. 1.What happens to the resistance of a thermistor as its temperature increases?
  2. 2.When is the resistance of an LDR highest?
  3. 3.Which component is best for a circuit that switches a street lamp on at dusk?
  4. 4.A thermistor has a p.d. of 5.0 V across it and a current of 0.025 A through it. What is its resistance?
  5. 5.Which device in a home heating system is most likely to contain a thermistor?
  6. 6.An LDR and a fixed resistor are in series across a battery. The light gets brighter. What happens to the p.d. across the LDR?