Skip to content

Cambridge IGCSE Physics (0625) · Electrical quantities

Resistance

4.2.4

Resistance is found from R = V/I and measured in ohms using a voltmeter and an ammeter. A longer metal wire has more resistance and a thicker one has less; Extended candidates use the proportional relationships.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

What resistance tells you (Core)

Every component opposes the flow of charge through it to some extent. That opposition is its resistance. For the same p.d., a component with a large resistance lets only a small current through, and one with a small resistance lets a large current through.

Resistance is measured in ohms (Ω). Cambridge expects every candidate to recall the equation that defines it:

R=VIR = \frac{V}{I}

where RR is the resistance in Ω, VV is the p.d. across the component in V and II is the current through it in A. One ohm is one volt per ampere. You will often need the rearranged forms V=IRV = IR and I=V/RI = V/R.

Finding a resistance by experiment (Core)

This is a Cambridge syllabus experiment, and you should be able to describe it and do the calculations.

  1. Connect a power supply, a switch, an ammeter and the resistor (or a length of wire) in series. Add a variable resistor in the same loop so you can change the current.
  2. Connect a voltmeter in parallel, directly across the resistor.
  3. Close the switch, read the ammeter and the voltmeter, then open the switch again.
  4. Adjust the variable resistor and take several more pairs of readings.
  5. Work out V÷IV \div I for each pair and find the mean.

You can also plot a graph of p.d. on the vertical axis against current on the horizontal axis. For a resistor of constant resistance it is a straight line through the origin, and its gradient equals the resistance.

Use small currents and open the switch after each reading. If the wire warms up, its resistance changes and the results are spoiled.

Length and thickness of a wire

A metal wire is a resistor in its own right. Two features of its shape matter.

  • Length (Core): a longer wire has a greater resistance.
  • Cross-sectional area (Core): a thicker wire, with a bigger cross-sectional area, has a smaller resistance.

A simple picture helps. A longer wire gives the drifting electrons a longer journey through the metal. A thicker wire is like a wider road, with room for more electrons to move side by side.

Sketching current–voltage graphs for a fixed resistor, a filament lamp and a diode is a Supplement skill with its own topic page in this course.

Worked example 1 (Core)

A torch lamp has a p.d. of 3.0 V across it and a current of 0.25 A through it. Calculate its resistance.

Equation and substitution:

R=VI=3.00.25R = \frac{V}{I} = \frac{3.0}{0.25}

Answer: R=12R = 12 Ω.

Worked example 2 (Supplement)

A 0.50 m length of nichrome wire has a resistance of 4.0 Ω. Find the resistance of (a) 1.5 m of the same wire and (b) a 0.50 m nichrome wire with twice the cross-sectional area.

(a) The length is 3 times larger, so the resistance is 3 times larger:

R=4.0×1.50.50=12 ΩR = 4.0 \times \frac{1.5}{0.50} = 12\ \Omega

(b) Twice the area means half the resistance: R=4.0÷2=2.0R = 4.0 \div 2 = 2.0 Ω.

Test it in the simulation

In the simulation above, wire a cell, an ammeter and a resistor into one loop, with a voltmeter connected across the resistor. Tap the resistor and give it a new value. Each time, divide the voltmeter reading by the ammeter reading: the answer matches the value you set. Then swap in a variable resistor and see the current fall as its resistance rises, while the cell's e.m.f. stays the same.

Equations

  • Potential difference, current and resistance

    Learn this

    V=IR

    potential difference = current × resistance

    Open calculator →

Common mistakes

  • Writing R = I/V or R = V × I instead of R = V/I.
  • Using a current in mA without converting it to A, giving a resistance 1000 times too small.
  • Connecting the voltmeter across the whole circuit or across the ammeter instead of directly across the resistor being tested.
  • Saying a thicker wire has more resistance. A larger cross-sectional area gives less resistance.
  • (Supplement) Assuming that doubling the diameter halves the resistance. The area becomes four times larger, so the resistance becomes one quarter.
  • Leaving the current switched on for a long time during the experiment, so the wire gets warm and its resistance drifts upwards.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A student wants to find the resistance of a resistor using a voltmeter and an ammeter.

    1. (a)Describe how the student should connect the ammeter and the voltmeter.

      2 marks
      Show the answer

      Answer: The ammeter is in series with the resistor; the voltmeter is in parallel, across the resistor.

      Marking points

      • ammeter in series with the resistor
      • voltmeter in parallel across the resistor
    2. (b)The voltmeter reads 4.8 V and the ammeter reads 0.30 A. Calculate the resistance.

      3 marks
      Show the answer

      Answer: R = V ÷ I = 4.8 ÷ 0.30 = 16 Ω

      Marking points

      • R = V/I
      • 4.8 ÷ 0.30
      • 16 Ω
    3. (c)Suggest why the student takes several readings with different currents.

      1 mark
      Show the answer

      Answer: To calculate a mean value of the resistance and check that it stays the same.

      Marking points

      • to find a mean / check the resistance is constant / reduce the effect of random errors
  2. 2.Wires P and Q are made of the same metal and have the same thickness. Wire Q is longer than wire P.

    1. (a)State which wire has the larger resistance.

      1 mark
      Show the answer

      Answer: Wire Q.

      Marking points

      • Q
    2. (b)Wire S is made of the same metal and has the same length as P, but it is thicker. State and explain how the resistance of S compares with the resistance of P.

      2 marks
      Show the answer

      Answer: S has a smaller resistance, because it has a larger cross-sectional area.

      Marking points

      • resistance of S is smaller
      • because S has a larger cross-sectional area
  3. 3.A 0.80 m length of constantan wire has a resistance of 2.4 Ω.

    1. (a)(Supplement) Calculate the resistance of a 2.0 m length of the same wire.

      2 marks
      Show the answer

      Answer: Resistance is proportional to length: R = 2.4 × (2.0 ÷ 0.80) = 6.0 Ω

      Marking points

      • resistance proportional to length / 2.4 × 2.0 ÷ 0.80
      • 6.0 Ω
    2. (b)(Supplement) A second constantan wire is also 0.80 m long but has three times the cross-sectional area. Calculate its resistance.

      2 marks
      Show the answer

      Answer: Resistance is inversely proportional to area: R = 2.4 ÷ 3 = 0.80 Ω

      Marking points

      • resistance inversely proportional to area / 2.4 ÷ 3
      • 0.80 Ω
  4. 4.A headlamp bulb in a car has a resistance of 3.0 Ω when it is lit. It is connected to a 12 V battery.

    1. (a)Calculate the current in the bulb.

      3 marks
      Show the answer

      Answer: I = V ÷ R = 12 ÷ 3.0 = 4.0 A

      Marking points

      • I = V/R
      • 12 ÷ 3.0
      • 4.0 A
    2. (b)A different bulb with a larger resistance is connected to the same battery. State the effect on the current.

      1 mark
      Show the answer

      Answer: The current is smaller.

      Marking points

      • current decreases / is smaller

Quick check

6 questions

  1. 1.What is the unit of resistance?
  2. 2.A p.d. of 6.0 V across a resistor gives a current of 0.20 A. What is the resistance?
  3. 3.(Supplement) A wire is replaced by one of the same metal and thickness but twice as long. What happens to the resistance?
  4. 4.Which change to a metal wire reduces its resistance?
  5. 5.(Supplement) The diameter of a wire is doubled while its length and metal stay the same. How does the new resistance compare with the old one?
  6. 6.A current of 0.10 A flows through a 47 Ω resistor. What is the p.d. across it?