Skip to content

Cambridge IGCSE Physics (0625) · Electrical quantities

Current–voltage graphs

4.2.4Supplement

Supplement. A filament lamp's current–voltage graph is a curve that gets less steep as the filament heats up. A fixed resistor's line is straight and runs through the origin, and a diode conducts in one direction only. At any point, R = V/I gives the resistance.

Loading simulation…

Symbols match your course. Open the full i–v characteristics simulation for more presets and teacher tools.

What this topic covers

Taking the readings (Core)

Connect an ammeter in series with the component and a variable d.c. supply, and a voltmeter across the component alone. Each pair of readings gives R=V/IR = V/I there. Turning the component round gives negative values.

Sketching the graphs (Supplement)

A sketch is marked on its shape, not on plotted points. Draw current, II, on the vertical axis and voltage, VV, on the horizontal axis, with the origin at the centre.

ComponentWhat your sketch must show
Resistor of constant resistanceA straight line through the origin, with the same slope on both sides
Filament lampA curve through the origin, steepest there and less steep as the voltage grows either way; the negative half is a half-turn copy of the positive half
DiodeAlong the voltage axis for every negative voltage and for small positive ones, then a sharp rise from roughly 0.6 V for silicon

Why each shape (Supplement)

  • Resistor: its resistance is the same at every voltage, so current is directly proportional to voltage.
  • Filament lamp: a bigger current heats the filament, and hot metal resists more, so every added volt brings a smaller rise in current. The heating ignores direction, so both halves match.
  • Diode: reversed, its resistance is enormous, so the current is almost zero. Forwards, the resistance falls sharply near 0.6 V and the current climbs steeply.

For a resistance at any point, divide VV by II there. With II on the vertical axis, a resistor's line has gradient 1/R1/R; the Resistance page plots VV vertically, which makes the gradient RR. A curve's slope never gives the resistance.

Worked example 1 (Core and Supplement): a torch lamp

A 2.5 V torch lamp gives 0.10 A at 0.50 V, 0.16 A at 1.2 V and 0.25 A at 2.5 V. Find its resistance at each voltage and explain the trend.

Equation: R=V/IR = V/I

Working: 0.500.10=5.0 Ω\dfrac{0.50}{0.10} = 5.0\ \Omega, 1.20.16=7.5 Ω\dfrac{1.2}{0.16} = 7.5\ \Omega, 2.50.25=10 Ω\dfrac{2.5}{0.25} = 10\ \Omega

Answer: the resistance doubles, from 5.0 Ω to 10 Ω: the biggest current makes the filament hottest, and hot metal resists more. Plotted, the points lie on a curve bending towards the voltage axis.

Worked example 2 (Supplement): a diode both ways

A silicon diode is in series with a protective resistor. Forwards, the voltmeter across the diode reads 0.68 V and the ammeter 17 mA. Reversed, they read −3.0 V and 0.0 mA.

Given: V=0.68V = 0.68 V, I=17I = 17 mA =0.017= 0.017 A

Equation: R=V/IR = V/I

Substitution: R=0.680.017R = \dfrac{0.68}{0.017}

Answer: R=40 ΩR = 40\ \Omega forwards. Reversed, V/IV/I cannot be worked out with zero current: the resistance is too large to measure.

A diode's circuit symbol is a triangle with a bar at its tip; the triangle shows which way conventional current may pass. An LED's symbol adds two arrows pointing away; it is a diode too, so it lights only with forward current.

Explore the graphs yourself

In the simulation above, a 12 V lamp is set to 6.0 V. Press Take a full set of readings: the power pack steps to 12 V, then to −12 V with the leads reversed. Tap the 12 V point (or 12.00 in the table). V÷IV \div I gives 24.0 Ω, but 1 ÷ gradient of the tangent gives 46.9 Ω, which is not the resistance.

Next, choose Diode, take a full set and press 0 to 0.8 V above the graph. The current is still 0.00 mA at 0.30 V and climbs steeply beyond about 0.6 V. The biggest forward p.d. in the table is only 0.74 V, as the 470 Ω resistor takes the rest; all four reversed readings show 0.00 mA.

Last, choose Resistor and 10 Ω, take a full set, then repeat with 100 Ω. The gradient under the graph falls from 0.100 to 0.0100 A/V, and 1 ÷ gradient returns each resistance.

Common mistakes

  • (Supplement) Drawing the lamp's curve bending upwards, or turning flat. It is steepest at the origin and keeps rising, only less steeply as the voltage grows.
  • (Supplement) Sketching only positive voltages. Show the negative side too: the lamp's curve repeats with a half turn about the origin, and the diode's current stays close to zero.
  • (Supplement) Starting the diode's forward current rising at 0 V. A silicon diode passes almost nothing until the voltage is roughly 0.6 V.
  • (Supplement) Explaining the lamp's shape with 'more current' alone. The key step is that the filament gets hotter, and its resistance rises with temperature.
  • (Supplement) Taking the resistance of a lamp or diode from the slope of its curve. Divide the voltage by the current at that point instead.
  • (Core) Putting a current in mA straight into R = V/I. Change 17 mA to 0.017 A first.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A student investigates how the current in a filament lamp varies with the voltage across it, for voltages from −6.0 V to +6.0 V.

    1. (a)(Supplement) Sketch the current–voltage graph for the lamp. Label the axes.

      3 marks
      Show the answer

      Answer: Current (vertical) and voltage (horizontal) axes labelled. A curve through the origin whose gradient becomes smaller as the voltage increases, without becoming horizontal. The negative part has the same shape, rotated through 180° about the origin.

      Marking points

      • axes labelled current / I and voltage / V
      • curve through the origin with a gradient that decreases as the voltage increases
      • same shape for negative voltages (rotated through 180° about the origin)
    2. (b)(Supplement) Explain the shape of the graph.

      2 marks
      Show the answer

      Answer: A bigger current raises the temperature of the filament. Its resistance increases with temperature, so the current rises by less for each extra volt.

      Marking points

      • bigger current, so the filament's temperature rises
      • resistance increases (so the current rises less for each extra volt)
    3. (c)(Core) At 4.8 V the current in the lamp is 0.40 A. Calculate the resistance of the lamp at this voltage.

      2 marks
      Show the answer

      Answer: R = V/I = 4.8 ÷ 0.40 = 12 Ω

      Marking points

      • R = V/I or 4.8 ÷ 0.40
      • 12 Ω
  2. 2.(Supplement) A silicon diode, a lamp and a battery are connected in series. The lamp lights.

    1. (a)Describe the circuit symbol for a diode and state what its shape shows.

      2 marks
      Show the answer

      Answer: A triangle with a short line (bar) across its point. The triangle points in the direction in which conventional current can pass through the diode.

      Marking points

      • triangle with a bar / line across its tip
      • triangle points in the direction of (conventional) current
    2. (b)Sketch the current–voltage graph for a diode, for positive and negative voltages.

      3 marks
      Show the answer

      Answer: Almost zero current for all negative voltages. Almost zero current for small positive voltages, up to about 0.6 V. Then the current rises very steeply.

      Marking points

      • (almost) zero current for negative voltages
      • (almost) zero current for small positive voltages
      • current rises steeply above a small positive voltage (about 0.6 V)
    3. (c)The battery is turned round. State and explain what happens to the lamp.

      2 marks
      Show the answer

      Answer: The lamp goes out. The diode is now reversed, so its resistance is very high and almost no current flows.

      Marking points

      • lamp goes out / does not light
      • reversed diode has a very high resistance / (almost) no current flows
  3. 3.A student is given a component sealed in a box with two terminals. The apparatus includes a variable d.c. power supply, an ammeter and a voltmeter.

    1. (a)(Core) State where the student should place each meter.

      2 marks
      Show the answer

      Answer: The ammeter goes in series with the component. The voltmeter goes in parallel, across the two terminals of the box.

      Marking points

      • ammeter in series with the component
      • voltmeter in parallel across the component
    2. (b)(Core) The readings are: 2.0 V gives 0.10 A, 4.0 V gives 0.20 A and 6.0 V gives 0.30 A. Calculate the resistance for each pair of readings.

      2 marks
      Show the answer

      Answer: R = V/I: 2.0 ÷ 0.10 = 20 Ω, 4.0 ÷ 0.20 = 20 Ω and 6.0 ÷ 0.30 = 20 Ω

      Marking points

      • R = V/I used, e.g. 2.0 ÷ 0.10
      • 20 Ω for all three
    3. (c)(Supplement) With the connections reversed, the readings are the same size but negative. Identify the component and give a reason.

      2 marks
      Show the answer

      Answer: A fixed resistor (a resistor of constant resistance). Its resistance is the same at every voltage and in both directions, so it is not a lamp, whose resistance changes, or a diode, which would block the reversed current.

      Marking points

      • fixed resistor / resistor of constant resistance
      • resistance the same at every voltage and in both directions (current proportional to voltage)
  4. 4.(Supplement) Resistors P and Q each have a constant resistance. On a graph of current (vertical axis) against voltage (horizontal axis), both give straight lines through the origin. The line for P is steeper.

    1. (a)State which resistor has the larger resistance. Explain your answer.

      2 marks
      Show the answer

      Answer: Q. At any given voltage, Q carries a smaller current than P, so V/I is larger for Q.

      Marking points

      • Q
      • for the same voltage Q has a smaller current, so V/I is larger
    2. (b)The line for P passes through the point where the voltage is 3.0 V and the current is 0.60 A. Calculate the resistance of P.

      2 marks
      Show the answer

      Answer: R = V/I = 3.0 ÷ 0.60 = 5.0 Ω

      Marking points

      • 3.0 ÷ 0.60
      • 5.0 Ω
    3. (c)The graph for a filament lamp is a curve. State how its resistance at 3.0 V can be found from the graph.

      1 mark
      Show the answer

      Answer: Read the current at 3.0 V and work out R = V/I (not the gradient of the curve).

      Marking points

      • read the current at 3.0 V and divide 3.0 V by it (not the gradient)

Quick check

6 questions

  1. 1.(Supplement) Which description matches the current–voltage graph of a filament lamp?
  2. 2.(Supplement) What makes a filament lamp's resistance go up as the voltage across it goes up?
  3. 3.(Core) A component has 3.0 V across it and 0.060 A through it. What is the resistance of the component?
  4. 4.(Supplement) A silicon diode is connected the wrong way round across a 3.0 V battery. What is the current in the diode?
  5. 5.(Supplement) Four resistors give four different straight lines through the origin on a graph of current (vertical axis) against voltage. Which line shows the smallest resistance?
  6. 6.(Supplement) Which component has a current–voltage graph that is the same shape for negative voltages but is not a straight line?