Skip to content

GCSE Physics — AQA · Electricity

I–V characteristics

4.2.1.4

An I–V graph shows whether a component's resistance stays the same. A resistor at constant temperature gives a straight line through the origin, while a lamp's curve gets less steep as its filament heats and a diode conducts one way only. Spec 4.2.1.4: both tiers, Physics and Combined Science.

Loading simulation…

Symbols match your course. Open the full i–v characteristics simulation for more presets and teacher tools.

Where this sits in AQA Physics

Spec point 4.2.1.4, Resistors, has no Higher-only or physics-only label, so it is common to both tiers and to Combined Science. It contains Required practical activity 4, which Combined Science courses may number differently.

The one equation is V=IRV = IR, from 4.2.1.3. AQA leaves it off the equation sheet, so learn it, along with R=VIR = \dfrac{V}{I}.

Three shapes to know

An I–V characteristic shows how one component's current depends on the p.d. across it. Current goes on the vertical axis. Readings with the connections swapped are negative, so the axes cross mid-grid.

  • Resistor at constant temperature: a straight line through the origin, continuing into the negative quarter. The current is directly proportional to the p.d., so the resistance stays fixed. AQA calls this an ohmic conductor, and its graph is linear.
  • Filament lamp: steep near the origin, then less and less steep as the p.d. grows either way. More current makes the filament hotter, and hotter metal has more resistance, so each extra volt adds less current. The curve never goes flat.
  • Diode: current passes one way only. Forwards, hardly any flows until roughly 0.6 V for a silicon diode, then it rises steeply. Backwards, its very high resistance lets almost nothing through. AQA quotes no switch-on value.

The lamp and diode graphs are non-linear: their resistance changes with the current.

Resistance from the graph

Pick a point, take its p.d. and current, and divide: R=VIR = \dfrac{V}{I}. This works for any component.

For a straight line through the origin, the gradient is current ÷ p.d., which is 1R\dfrac{1}{R}. So R=1gradientR = \dfrac{1}{\text{gradient}}, and a steeper line means a smaller resistance. On a curve, a tangent's gradient does not give the resistance.

Worked example 1: a lamp at two points

On a 12 V filament lamp's I–V graph, the current is 0.60 A at 1.5 V and 2.0 A at 12 V. Find the resistance at each point.

Given: V1=1.5V_1 = 1.5 V, I1=0.60I_1 = 0.60 A; V2=12V_2 = 12 V, I2=2.0I_2 = 2.0 A

Equation: R=VIR = \dfrac{V}{I}

Substitution: R1=1.50.60R_1 = \dfrac{1.5}{0.60} and R2=122.0R_2 = \dfrac{12}{2.0}

Answer: R1=2.5 ΩR_1 = 2.5\ \Omega and R2=6.0 ΩR_2 = 6.0\ \Omega

If the resistance had stayed at 2.5 Ω, 12 V would push 4.8 A through it. Only 2.0 A flows, because the hotter filament resists more.

Worked example 2: resistance from a gradient

A resistor's I–V line runs from the origin through 5.0 V, 0.20 A.

Gradient: change in current ÷ change in p.d. =0.205.0=0.040= \dfrac{0.20}{5.0} = 0.040 A/V

Equation and substitution: R=1gradient=10.040R = \dfrac{1}{\text{gradient}} = \dfrac{1}{0.040}

Answer: R=25 ΩR = 25\ \Omega, matching 5.0÷0.205.0 \div 0.20.

Required practical activity 4

  1. Wire a d.c. supply, switch, variable resistor and ammeter in one loop with the component. The voltmeter goes across the component alone.
  2. Use the variable resistor, or a variable supply, to set at least five p.d.s, recording both meters each time.
  3. Swap the component's leads over and repeat, recording negative values.
  4. Repeat readings, find means, plot current against p.d. and add a best-fit line or curve.

Keep the resistor's current low and switch off after each reading, so its temperature stays steady. Protect the diode with a resistor in series and take extra readings near 0.6 V. Let the lamp heat up, within its rating.

Thermistors and LDRs

4.2.1.4 also covers two sensors: a thermistor's resistance falls as it warms, and an LDR's falls in brighter light. Their uses, such as thermostats and dusk-activated lights, are on the LDRs and thermistors page; this simulation has neither.

On the virtual bench

In the simulation above, the filament lamp starts at 6.0 V, taking 0.354 A, so the Resistance card shows 16.9 Ω. Press Record, drag Power pack output to 12.0 V and record: 0.500 A and 24.0 Ω. Record at 2.0 V as well: 0.219 A and 9.13 Ω. Press Reverse and record again: −0.219 A, the same size but reversed.

Now choose Resistor, then 47 Ω, and press Take a full set of readings. Under the graph, 1 ÷ gradient gives 47.0 Ω. Last, choose Diode and take a full set. Every reversed reading is 0.00 mA, and the run ends reversed, so the Resistance card says "too large to measure".

Equations

  • Potential difference, current and resistance

    Learn this

    V=IR

    potential difference = current × resistance

    Open calculator →

Common mistakes

  • Taking a lamp's resistance from the gradient of its curve, or of a tangent. Use the p.d. and current values at the point itself in R = V ÷ I.
  • Drawing the lamp's curve going flat at high p.d. It keeps rising, only less steeply.
  • Saying the lamp's resistance goes up 'because the current goes up'. The cause examiners want is the filament getting hotter.
  • Drawing a diode's forward current rising from 0 V, or calling its reverse resistance zero. Almost nothing flows until roughly 0.6 V forwards, and its resistance in reverse is very high.
  • Saying a steeper straight line shows a larger resistance. With current on the vertical axis, the gradient is 1 ÷ R, so a steeper line means a smaller resistance.
  • Connecting the voltmeter in series, or across both the component and the variable resistor. It belongs across the component only.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A student plots the I–V characteristic of a filament lamp. The current is 0.20 A when the potential difference is 3.0 V, and 0.36 A when the potential difference is 9.0 V.

    1. (a)Write down the equation that connects resistance (R), current (I) and potential difference (V).

      1 mark
      Show the answer

      Answer: V = IR

      Marking points

      • V = IR
    2. (b)Work out the lamp's resistance at 9.0 V.

      2 marks
      Show the answer

      Answer: R = V ÷ I = 9.0 ÷ 0.36 = 25 Ω

      Marking points

      • 9.0 = 0.36 × R or R = 9.0 ÷ 0.36
      • R = 25 Ω
    3. (c)At 3.0 V the resistance of the lamp is 15 Ω. Explain why its resistance is greater at 9.0 V.

      2 marks
      Show the answer

      Answer: At 9.0 V the current is larger, so the filament is at a higher temperature. A hotter metal filament has a greater resistance.

      Marking points

      • A larger current makes the filament hotter (its temperature is higher).
      • A hotter filament has a greater resistance.
    4. (d)The student reverses the connections to the lamp and repeats the readings. Describe how the graph for negative potential differences compares with the graph for positive ones.

      1 mark
      Show the answer

      Answer: It has the same shape: each p.d. gives a current of equal size flowing the other way, so the curve for negative values is the positive curve rotated by 180° around the origin.

      Marking points

      • Same shape (equal-sized current, opposite direction, for each p.d.; accept rotational symmetry about the origin).
  2. 2.A student has a fixed resistor, a battery, a switch, a variable resistor, an ammeter, a voltmeter and connecting leads. The student wants to find the I–V characteristic of the resistor.

    1. (a)Describe a method the student could use. Include how to get readings for negative values of potential difference.

      6 marks
      Show the answer

      Answer: Join the battery, switch, variable resistor, ammeter and fixed resistor in series, and connect the voltmeter in parallel across the fixed resistor only. Close the switch, adjust the variable resistor for a low p.d., read both meters, then open the switch. Change the variable resistor to obtain at least five different p.d.s, recording the current and the p.d. each time. Reverse the connections to the fixed resistor (or to the battery) and repeat, recording these readings as negative. Repeat each reading and calculate a mean current. Plot current on the vertical axis against p.d. on the horizontal axis and draw a line of best fit. (Level-of-response marking: the answer is judged as a whole. Level 3, 5–6 marks: a clear, logically ordered method that would give valid results, covering meter positions, changing the p.d., negative values and repeats. Level 2, 3–4 marks: most of the steps are present, but an important step is missing or the order is unclear. Level 1, 1–2 marks: some relevant points, such as where one meter goes, but not a workable method. 0 marks: nothing worthy of credit.)

      Marking points

      • Ammeter connected in series, and voltmeter connected in parallel, with the fixed resistor.
      • Variable resistor adjusted to change the p.d. across the resistor (and so the current).
      • Current and p.d. recorded for a range of settings (at least five).
      • Connections to the resistor (or battery) reversed to obtain negative values.
      • Each reading repeated and a mean calculated.
      • Current plotted against p.d. with a line of best fit (or: switch opened between readings so the resistor does not heat up).
    2. (b)Explain why the student should open the switch between readings.

      2 marks
      Show the answer

      Answer: The current heats the resistor. A change in its temperature would change its resistance, but the investigation needs the resistor at a constant temperature.

      Marking points

      • The current causes heating in the resistor.
      • A change in temperature would change the resistance (the temperature must stay constant).
    3. (c)The student's best-fit line is straight and goes through the origin. What does this tell you about the resistor?

      1 mark
      Show the answer

      Answer: Its resistance does not change: the current is proportional to the p.d., so it is an ohmic conductor.

      Marking points

      • Resistance stays the same (current proportional to p.d.; accept ohmic conductor).
  3. 3.Three components, X, Y and Z, are tested in turn. X gives a straight line through the origin. Y gives a curve through the origin that gets less steep as the potential difference increases, with the same shape for negative values. Z gives almost no current for negative values, and almost none for positive values below about 0.6 V, after which the current rises steeply.

    1. (a)Name components X, Y and Z.

      3 marks
      Show the answer

      Answer: X is a resistor at constant temperature, Y is a filament lamp and Z is a diode.

      Marking points

      • X: (fixed) resistor (at constant temperature)
      • Y: filament lamp
      • Z: diode
    2. (b)When the potential difference across Z is 0.72 V, the current through it is 24 mA. Calculate the resistance of Z at this potential difference.

      3 marks
      Show the answer

      Answer: I = 24 mA = 0.024 A. R = V ÷ I = 0.72 ÷ 0.024 = 30 Ω

      Marking points

      • Current converted to 0.024 A
      • R = 0.72 ÷ 0.024
      • R = 30 Ω
    3. (c)Explain what the graph shows about the resistance of Z when the potential difference is reversed.

      2 marks
      Show the answer

      Answer: Almost no current flows in the reverse direction, so the resistance of Z is very high.

      Marking points

      • The current is (almost) zero for negative potential differences.
      • So the resistance of Z is very high when the potential difference is reversed.
  4. 4.A resistor is kept at constant temperature. Its I–V graph, with current on the vertical axis, is straight and passes through the origin. One point on the line is at a potential difference of 6.0 V and a current of 0.12 A.

    1. (a)Calculate the gradient of the line.

      2 marks
      Show the answer

      Answer: gradient = change in current ÷ change in p.d. = 0.12 ÷ 6.0 = 0.020 A/V

      Marking points

      • gradient = 0.12 ÷ 6.0
      • gradient = 0.020 (A/V)
    2. (b)Use your answer to calculate the resistance of the resistor.

      2 marks
      Show the answer

      Answer: R = 1 ÷ gradient = 1 ÷ 0.020 = 50 Ω (as a check, 6.0 ÷ 0.12 = 50 Ω)

      Marking points

      • R = 1 ÷ 0.020 (or R = 6.0 ÷ 0.12)
      • R = 50 Ω
    3. (c)A second resistor has a larger resistance. State how its I–V graph would differ from the first one.

      1 mark
      Show the answer

      Answer: Its line would be less steep (a smaller gradient), but still straight and through the origin.

      Marking points

      • Less steep line / smaller gradient (still straight through the origin).

Quick check

6 questions

  1. 1.With 4.0 V across it, a filament lamp carries a current of 0.25 A. What is its resistance at this point?
  2. 2.What happens to the resistance of a filament lamp as the current through it increases?
  3. 3.The p.d. across a diode is reversed. Which statement describes the diode now?
  4. 4.With current on the vertical axis, the I–V line of a resistor passes through the origin with a gradient of 0.050 A/V. What is its resistance?
  5. 5.In Required practical 4, where should the voltmeter be connected?
  6. 6.How does a student get readings with a negative p.d. in Required practical 4?