Skip to content

GCSE Physics — AQA · Electricity

Series and parallel circuits

4.2.2

In series, components share the supply p.d., carry the same current and have a total resistance R total = R1 + R2. In parallel, each branch has the same p.d., branch currents add up, and the total resistance is below the smallest resistor.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

What spec point 4.2.2 asks of you

Components can be joined in two ways: one after another in series, or side by side in parallel. Many real circuits mix both. This topic is on both tiers, and its ideas appear all through the electricity paper.

There is one equation here, and you must remember it:

Rtotal=R1+R2R_{\text{total}} = R_1 + R_2

It gives the total resistance of two resistors in series, with every resistance in ohms (Ω). For resistors in parallel, AQA does not expect you to use a formula. You only need to know that the total is less than the smallest single resistance.

Rules for a series circuit

A series circuit has just one route for the charge.

  • Current: each component carries the same current.
  • Potential difference: the p.d. of the supply is split between the components. Adding the p.d.s across all of them gives the supply p.d.
  • Resistance: the total is found by adding the separate resistances.

The component with the largest resistance gets the largest share of the p.d.

Rules for a parallel circuit

In a parallel circuit, the components are on separate branches that meet at the same two junctions.

  • Potential difference: every branch has the same p.d. across it.
  • Current: the current from the supply splits at a junction. Add the branch currents together and you get the total current.
  • Resistance: two resistors in parallel have a total resistance smaller than either one alone.

The branch with the smaller resistance carries the larger current.

Why the total resistance goes up or down

AQA wants a qualitative explanation, in words.

Adding a resistor in series. The charge now has to pass through one more obstacle on its only route. With the same supply p.d., less current flows. A smaller current for the same p.d. means a larger total resistance.

Adding a resistor in parallel. The new branch opens up an extra route for the charge. The original branches still have the same p.d., so their currents do not change. The new branch adds its own current on top. More total current for the same p.d. means a smaller total resistance.

Worked example 1: a series circuit

A 9.0 V battery is connected to a 12 Ω resistor and a 6.0 Ω resistor in series. Calculate the current, then the p.d. across each resistor.

Given: V=9.0 VV = 9.0\ \text{V}, R1=12 ΩR_1 = 12\ \Omega, R2=6.0 ΩR_2 = 6.0\ \Omega

Equation: Rtotal=R1+R2R_{\text{total}} = R_1 + R_2, then I=VRtotalI = \dfrac{V}{R_{\text{total}}}

Substitution: Rtotal=12+6.0=18 ΩR_{\text{total}} = 12 + 6.0 = 18\ \Omega, so I=9.018I = \dfrac{9.0}{18}

Answer: I=0.50 AI = 0.50\ \text{A} through both resistors.

Using V=IRV = IR for each one: 0.50×12=6.0 V0.50 \times 12 = 6.0\ \text{V} and 0.50×6.0=3.0 V0.50 \times 6.0 = 3.0\ \text{V}. These add to 9.0 V, the supply p.d.

Worked example 2: two resistors side by side

A 6.0 V supply is connected across a 10 Ω resistor and a 15 Ω resistor in parallel. Work out the current drawn from the supply and the total resistance. No parallel formula is needed.

Given: each branch has V=6.0 VV = 6.0\ \text{V} across it.

Equation: I=VRI = \dfrac{V}{R} for each branch, then Rtotal=VItotalR_{\text{total}} = \dfrac{V}{I_{\text{total}}}

Substitution: I1=6.010=0.60 AI_1 = \dfrac{6.0}{10} = 0.60\ \text{A} and I2=6.015=0.40 AI_2 = \dfrac{6.0}{15} = 0.40\ \text{A}, so Itotal=1.0 AI_{\text{total}} = 1.0\ \text{A}

Answer: Rtotal=6.01.0=6.0 ΩR_{\text{total}} = \dfrac{6.0}{1.0} = 6.0\ \Omega, which is less than 10 Ω, the smaller resistor.

Required practical activity 3 includes measuring the resistance of resistor combinations in series and in parallel. AQA also expects you to explain how series circuits are used for measuring and testing. An ammeter in series with a component, plus a voltmeter across it, is the standard way to test that component.

Using the simulation

In the simulation above, load Series and read the ammeter. Add a resistor into the loop and watch the current fall. Then load Parallel, where the ammeter beside the battery measures the total current. Add a third lamp on a new branch and the total current rises, while the lamps already there stay just as bright.

Equations

Common mistakes

  • Adding resistances in parallel as if they were in series (10 Ω and 40 Ω in parallel is not 50 Ω).
  • Saying the p.d. is shared between parallel branches; each branch has the same p.d.
  • Saying the current is shared between components in series; the current is the same through each one.
  • Explaining why parallel resistance falls without mentioning that the total current from the supply increases.
  • Thinking a bigger resistor in parallel carries more current; the branch with less resistance carries more.
  • Forgetting that in series the largest resistor takes the largest share of the p.d.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A 20 Ω resistor and a 30 Ω resistor are connected in series with a 12 V battery.

    1. (a)Calculate the total resistance of the circuit.

      1 mark
      Show the answer

      Answer: R total = 20 + 30 = 50 Ω

      Marking points

      • 50 Ω
    2. (b)Calculate the current in the circuit.

      2 marks
      Show the answer

      Answer: I = V ÷ R = 12 ÷ 50 = 0.24 A

      Marking points

      • I = 12 ÷ 50
      • I = 0.24 A
    3. (c)Calculate the potential difference across the 30 Ω resistor.

      2 marks
      Show the answer

      Answer: V = I R = 0.24 × 30 = 7.2 V

      Marking points

      • V = 0.24 × 30 (allow their current from the previous part)
      • V = 7.2 V
  2. 2.Two lamps are connected in parallel across a 3.0 V cell. An ammeter in one branch reads 0.20 A and an ammeter in the other branch reads 0.30 A.

    1. (a)State the potential difference across each lamp.

      1 mark
      Show the answer

      Answer: 3.0 V

      Marking points

      • 3.0 V across each lamp.
    2. (b)Calculate the current through the cell.

      1 mark
      Show the answer

      Answer: 0.20 + 0.30 = 0.50 A

      Marking points

      • 0.50 A
    3. (c)A third lamp is added in parallel. Explain why the total resistance of the circuit decreases.

      3 marks
      Show the answer

      Answer: The new branch gives the charge another path. The p.d. across each branch is unchanged, so the total current from the cell increases. A bigger current for the same p.d. means the total resistance is smaller.

      Marking points

      • An extra branch provides another path for the charge.
      • The total current (from the cell) increases.
      • The p.d. stays the same, so R = V ÷ I gives a smaller total resistance.
  3. 3.A string of decorative lights can be wired with all the lamps in series or with all the lamps in parallel.

    1. (a)Describe the difference between a series circuit and a parallel circuit.

      2 marks
      Show the answer

      Answer: A series circuit has only one path for the charge, so every component is in the same loop. A parallel circuit has two or more branches, each giving a separate path.

      Marking points

      • Series: one path / one loop through every component.
      • Parallel: more than one path / separate branches.
    2. (b)Give one advantage of wiring the lamps in parallel.

      1 mark
      Show the answer

      Answer: If one lamp breaks, the others stay lit.

      Marking points

      • If one lamp fails the others still work (or each lamp gets the full supply p.d.).
  4. 4.A 10 Ω resistor and a 40 Ω resistor are connected in parallel.

    1. (a)Which of these could be the total resistance of the combination: 8 Ω, 25 Ω or 50 Ω? Give a reason for your answer.

      2 marks
      Show the answer

      Answer: 8 Ω, because the total resistance of resistors in parallel is less than the smallest individual resistance (10 Ω).

      Marking points

      • 8 Ω
      • Total resistance in parallel is less than the smallest resistor.

Quick check

6 questions

  1. 1.Two lamps are in series with a cell. How does the current in the first lamp compare with the current in the second?
  2. 2.A 4.0 Ω resistor and an 8.0 Ω resistor are connected in series. What is their total resistance?
  3. 3.A 6.0 Ω resistor and a 12 Ω resistor are connected in parallel. Which statement about the total resistance is correct?
  4. 4.In a parallel circuit, the branch currents are 0.30 A and 0.50 A. What is the current from the supply?
  5. 5.A 6.0 V battery is in series with a lamp and a resistor. The p.d. across the lamp is 2.5 V. What is the p.d. across the resistor?
  6. 6.Why are the lamps in a house wired in parallel?