Skip to content

GCSE Physics — AQA · Electricity

Circuit symbols

4.2.1.1

Recognise the standard symbols on the AQA list and use them to draw and read circuit diagrams, including where to place ammeters and voltmeters.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

What AQA expects from you

Spec point 4.2.1.1 is short, but almost every electricity question depends on it. You need to recognise each standard symbol, draw it neatly, and work out what a circuit diagram is telling you. This is required on both tiers, in Combined Science and in GCSE Physics.

There is no equation to remember for this spec point. Even so, symbol marks are easy to lose. If an examiner cannot tell your fuse from your resistor, you lose the mark.

The fourteen symbols on the AQA list

ComponentHow the symbol is drawnWhat it does
CellA long line beside a shorter line; the long line is the positive terminalProvides a potential difference that pushes charge round
BatteryTwo or more cell symbols joined, often with a dashed line between themSeveral cells in series give a larger p.d.
Switch (open or closed)A short lever between two small circles, raised when open and lying flat when closedBreaks or completes the circuit
LampA circle with a cross insideLights up when current passes
FuseA rectangle with a line running all the way through itMelts and cuts the current if it gets too large
ResistorA plain empty rectangleHas a fixed resistance
Variable resistorA rectangle with a diagonal arrow across itIts resistance can be adjusted to change the current
AmmeterA circle containing the letter AMeasures current
VoltmeterA circle containing the letter VMeasures potential difference
DiodeA triangle pointing at a short bar, drawn inside a circle in the AQA versionLets current pass in one direction only
LEDThe diode symbol with two small arrows pointing away from itA diode that gives out light
ThermistorA rectangle crossed by a slanted line with a short flat foot at one endResistance falls as temperature rises
LDRA small rectangle inside a circle, with two arrows pointing in towards itResistance falls as light gets brighter

The open and closed switch count as two separate symbols on the AQA list, which is how thirteen rows give fourteen symbols. A good memory trick for the diode family: arrows pointing out mean light is given out (LED), while arrows pointing in mean light falls on the part (LDR).

Drawing a diagram that earns the marks

  • Use a ruler and a pencil. Wires are straight lines with square corners.
  • Leave no gaps. A gap in a wire means the circuit is broken, so no current flows.
  • Draw the wire up to each symbol, but never through the middle of it.
  • Put the ammeter in series, in the same loop as the component.
  • Put the voltmeter in parallel, with its two leads joined across the component.
  • Show a dot where three or more wires meet at a junction.

Worked example: reading a test circuit

A diagram shows a battery, a closed switch, a fixed resistor and an ammeter all in one loop. A voltmeter is joined across the resistor. The ammeter reads 0.25 A and the voltmeter reads 3.0 V. What is the resistance of the resistor?

Given: I=0.25 AI = 0.25\ \text{A}, V=3.0 VV = 3.0\ \text{V}

Equation: V=IRV = IR (from spec point 4.2.1.3; you must remember it), so R=VIR = \dfrac{V}{I}

Substitution: R=3.00.25R = \dfrac{3.0}{0.25}

Answer: R=12 ΩR = 12\ \Omega

This is the basic circuit AQA expects when you are asked how to measure the resistance of a component, so learn it by heart. A variable resistor is often added in series so that the current can be changed.

Using the simulation

In the simulation above, open the Empty circuit and place a resistor, an ammeter and wires to make one loop. Add a voltmeter across the resistor, then select the resistor to read the current and p.d. Next, move the voltmeter so that it sits in series with the resistor and watch the current drop to almost nothing. Try swapping in an LDR and a thermistor too, and use the light and temperature sliders to see how their resistance changes.

Common mistakes

  • Drawing the voltmeter in series with a component instead of in parallel across it.
  • Confusing the fuse (a line runs right through the rectangle) with the plain resistor rectangle.
  • Drawing the LED arrows pointing inwards or the LDR arrows pointing outwards; LED arrows point away, LDR arrows point in.
  • Leaving small gaps between wires and symbols, which makes the circuit look incomplete.
  • Drawing the thermistor as a variable resistor: the thermistor line has a flat foot, the variable resistor has an arrowhead.
  • Calling a single cell a battery; a battery is two or more cells joined together.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A student sets up a circuit to find the resistance of a filament lamp. The circuit contains a battery, a closed switch, the lamp, an ammeter and a voltmeter.

    1. (a)The lamp symbol is drawn on the circuit diagram. Describe what the lamp symbol looks like.

      1 mark
      Show the answer

      Answer: A circle with a cross inside it.

      Marking points

      • Circle with a cross (X) drawn inside it.
    2. (b)Describe how the ammeter and the voltmeter should be connected in the circuit.

      2 marks
      Show the answer

      Answer: The ammeter is in series with the lamp. The voltmeter is in parallel across the lamp.

      Marking points

      • Ammeter connected in series with the lamp.
      • Voltmeter connected in parallel with (across) the lamp.
    3. (c)The ammeter reads 0.40 A and the voltmeter reads 2.4 V. Calculate the resistance of the lamp. Give the unit.

      3 marks
      Show the answer

      Answer: R = V ÷ I = 2.4 ÷ 0.40 = 6.0 Ω

      Marking points

      • 2.4 = 0.40 × R or R = 2.4 ÷ 0.40
      • R = 6.0 (accept 6)
      • Unit: Ω (ohms)
  2. 2.A circuit diagram for a dimmer switch includes a component drawn as a rectangle with a diagonal arrow across it.

    1. (a)Name this component.

      1 mark
      Show the answer

      Answer: Variable resistor.

      Marking points

      • Variable resistor (accept rheostat).
    2. (b)Explain why this component is included in a circuit used to measure the resistance of a component.

      2 marks
      Show the answer

      Answer: Changing its resistance changes the current in the circuit, so several pairs of current and p.d. readings can be taken.

      Marking points

      • Its resistance can be changed, which changes the current (and p.d.).
      • So a range of readings can be taken (or readings can be repeated).
  3. 3.Two students compare circuit symbols that look alike.

    1. (a)Give one difference between the circuit symbol for a diode and the symbol for an LED.

      1 mark
      Show the answer

      Answer: The LED symbol has two arrows pointing away from it.

      Marking points

      • LED has arrows pointing outwards (away from the symbol).
    2. (b)Give one difference between the circuit symbol for a fuse and the symbol for a resistor.

      1 mark
      Show the answer

      Answer: The fuse symbol has a line passing through the rectangle from end to end.

      Marking points

      • Fuse has a line running through the rectangle; resistor rectangle is empty.
    3. (c)One student draws a voltmeter in series with a lamp and a battery. Explain why the lamp does not light.

      2 marks
      Show the answer

      Answer: A voltmeter has a very high resistance, so the current in the loop is almost zero and the lamp does not light.

      Marking points

      • Voltmeter has a very high resistance.
      • So the current is (almost) zero / too small to light the lamp.
  4. 4.A torch is drawn as a circuit diagram. The power supply is shown as three cell symbols joined in series, all facing the same way. Each cell has a potential difference of 1.5 V.

    1. (a)Give the name used for two or more cells joined together.

      1 mark
      Show the answer

      Answer: A battery.

      Marking points

      • Battery.
    2. (b)Calculate the total potential difference of the three cells.

      1 mark
      Show the answer

      Answer: 3 × 1.5 = 4.5 V

      Marking points

      • 4.5 V
    3. (c)State which line of a cell symbol is the positive terminal.

      1 mark
      Show the answer

      Answer: The longer, thinner line.

      Marking points

      • The longer (taller, thinner) line.

Quick check

6 questions

  1. 1.Which component is shown by a circle with a cross inside it?
  2. 2.A circuit symbol is a rectangle with a straight line running through it from one end to the other. What is it?
  3. 3.Which symbol has two arrows pointing in towards it?
  4. 4.Which meter must be connected in series with a component?
  5. 5.A circuit symbol is a rectangle crossed by a slanted line that has a short flat foot. What is it?
  6. 6.On a cell symbol, what does the longer, thinner line show?