What AQA asks for: spec point 4.1.2.2
Every GCSE Physics and Combined Science student meets efficiency, on both tiers. Neither version of the efficiency equation is on the equation sheet, so you must remember both. Questions may ask for an efficiency as a decimal or as a percentage. Describing ways to increase efficiency is Higher tier only.
Two equations, one idea
Efficiency compares what you get out usefully with everything you put in:
Choose the energy version when the data are in joules and the power version when they are in watts; never divide joules by watts. The units cancel, so efficiency has no unit. Multiply the decimal by 100 for a percentage, so 0.35 becomes 35%. Energy cannot be created, so no device gives out more useful energy than it takes in: efficiency is never more than 1 (100%).
Whatever is not useful is wasted:
wasted energy = total input energy − useful output energy
Worked example 1: a delivery drone. A drone of mass 2.0 kg climbs 30 m at a steady speed. During the climb its motors take 1800 J from the battery. Find the efficiency of lifting the drone. Take N/kg.
Given: kg, m, total input J. Useful output: the gain in the gravitational potential store, J. Equation: efficiency . Substitution: efficiency . Answer: 0.33, or 33% (2 s.f.). The other 1212 J warms the motors and churns the air, and ends up dissipated.
Worked example 2: working backwards. A garden pump has an efficiency of 65%. It must give out 520 W of useful power. What total power input does it need?
Given: efficiency , useful power output W. Equation: rearranged, total power input . Substitution: . Answer: 800 W. The pump wastes W.
Efficiency from a Sankey diagram
The AQA specification does not name Sankey diagrams, but a question could still show one. In a Sankey diagram, arrow widths are drawn to scale. Divide the width of the useful arrow by the width of the input arrow and you have the efficiency. A thin useful arrow beside a fat wasted arrow means a device that wastes most of its input.
Higher tier: making a transfer more efficient
To raise the efficiency of an intended transfer, reduce the energy that is dissipated. Say what you would change and which wasted transfer it cuts:
- lubricate bearings, gears and chains, so less work is done against friction
- streamline vehicles, so less work is done against air resistance
- insulate things that should stay hot, such as ovens and hot-water tanks
- use thicker cables with less resistance, so a current heats them less
- swap filament lamps for LEDs, which send a larger share of their input out as light.
Foundation students still need lubrication and thermal insulation as ways of reducing unwanted transfers (spec 4.1.2.1).
Using the simulation
In the simulation above, leave the Electric kettle at its starting 2000 W for 150 s. The Efficiency card gives the answer both ways, 0.870 and 87.0%, and the Check it with the equations panel reaches it by dividing 260900 J by 300000 J. The Wasted card holds the other 39.1 kJ, so useful plus wasted makes up the full 300 kJ.
Now drag Time switched on up to 300 s. The water boils at 196 s and the kettle switches itself off, having taken in 392 kJ and given 336 kJ to the water. The efficiency drops to 0.857 (85.7%): the hotter the kettle gets, the faster it leaks energy into the room. Higher tier link: insulating the kettle would cut this loss and raise its efficiency.
For Battery torch left on, the batteries start with 20.0 kJ. Swapping the Bulb from Filament to LED lifts the efficiency card from 0.0500 (5.00%) to 0.250 (25.0%). In the Sankey diagram, the light arrow grows five times wider.
In Bungee jump and Ball thrown straight up, "useful" just follows one chosen store, so the efficiency shown there describes where the energy ended up, not how well a machine works.