An original Labverse practice paper — not an official exam paper
GCSE Physics — AQA
AQA GCSE Physics Paper 1 practice paper B
Written by Labverse from our own exam-style questions, to the same time and total marks as AQA’s Paper 1 (8463/1F, 8463/1H), on the same topics. It is not set, checked or endorsed by AQA.
- Time allowed
- 1 hour 45 minutes
- Total marks
- 100
- Questions
- 17
- Level
- All tiers
Instructions
- Answer every question. Work in one sitting and stop when the time is up.
- The marks for each part are shown beside it. Use them to judge how much to write.
- Show your working for calculations and give the unit with every answer.
To print the answers too, open the mark scheme at the end first.
Marks by topic
- Working scientifically · 4 marks
- Energy · 18 marks
- Electricity · 36 marks
- Particle model of matter · 19 marks
- Atomic structure · 23 marks
Questions
- Question 1 (4 marks)Accuracy, precision and errors
A student has two thermometers. Thermometer P is a liquid-in-glass thermometer marked every 1 °C. Thermometer Q is digital and shows temperatures to 0.1 °C.
(a)Give the resolution of thermometer Q.
[1](b)Both thermometers are put into melting ice, which is at 0 °C. P reads 0 °C and Q reads 1.4 °C. Explain why Q gives less accurate readings than P even though its resolution is better.
[2](c)Q then reads 37.9 °C in a beaker of warm water. Assume its error is the same at all temperatures. Calculate the corrected temperature.
[1]
- Question 2 (5 marks)Specific heat capacity
An electric storage heater contains concrete blocks with a total mass of 120 kg. Overnight, the blocks are heated from 15 °C to 65 °C. Specific heat capacity of concrete = 880 J/kg °C.
(a)Calculate the energy stored in the concrete overnight.
[3](b)Explain why the designer chose a large mass of a material with a high specific heat capacity.
[2]
- Question 3 (8 marks)Efficiency
Higher tier. The petrol engine of a car has an efficiency of 0.30.
(a)In one minute, the fuel supplies 1.5 MJ of energy to the engine. Calculate the useful energy output of the engine in that minute.
[2](b)Describe two ways in which the car could be made more efficient. Explain how each one works.
[4](c)Explain why the efficiency of the engine is less than 1.
[2]
- Question 4 (5 marks)Energy resources
A student writes a list of energy resources: coal, geothermal, natural gas, nuclear fuel, tides, wind.
(a)Give two resources from the list that are non-renewable.
[2](b)What is meant by a renewable energy resource?
[1](c)Most oil in the UK is used for transport. Name one renewable energy resource that could be used for transport instead of oil.
[1](d)Geothermal power stations are very reliable. Suggest why the UK generates very little electricity from geothermal energy.
[1]
- Question 5 (8 marks)Current, resistance and potential difference
A student investigates how the resistance of a wire depends on its length. The wire is fixed along a metre ruler and two crocodile clips are used to select the length being tested.
(a)Describe how the student could use an ammeter and a voltmeter to find the resistance of a 50 cm length of wire.
[4](b)For one length, the voltmeter reads 1.8 V and the ammeter reads 0.45 A. Calculate the resistance of this length of wire.
[2](c)Explain why the student should switch the circuit off between readings.
[2]
- Question 6 (6 marks)I–V characteristics
A student plots the I–V characteristic of a filament lamp. The current is 0.20 A when the potential difference is 3.0 V, and 0.36 A when the potential difference is 9.0 V.
(a)Write down the equation that connects resistance (R), current (I) and potential difference (V).
[1](b)Work out the lamp's resistance at 9.0 V.
[2](c)At 3.0 V the resistance of the lamp is 15 Ω. Explain why its resistance is greater at 9.0 V.
[2](d)The student reverses the connections to the lamp and repeats the readings. Describe how the graph for negative potential differences compares with the graph for positive ones.
[1]
- Question 7 (5 marks)Series and parallel circuits
A 20 Ω resistor and a 30 Ω resistor are connected in series with a 12 V battery.
(a)Calculate the total resistance of the circuit.
[1](b)Calculate the current in the circuit.
[2](c)Calculate the potential difference across the 30 Ω resistor.
[2]
- Question 8 (5 marks)Mains electricity
A bicycle lamp runs from a battery. A table lamp runs from the UK mains supply.
(a)Name the type of potential difference provided by the battery.
[1](b)Explain how the potential difference of the mains supply is different from the potential difference of the battery.
[2](c)Give the frequency and the potential difference of the UK mains supply.
[2]
- Question 9 (6 marks)The National Grid
A power station sends out 500 MW. In one part of the National Grid, 497 MW of this reaches the substations at the far end of the transmission cables.
(a)Calculate the efficiency of the transmission cables.
[2](b)State what happens to the 3 MW that does not reach the substations.
[1](c)The same power is sent along the same cables at a lower potential difference. Explain what happens to the efficiency of the transmission.
[3]
- Question 10 (6 marks)Static electricity and electric fieldsPhysics only
A student is given two polythene rods, an acetate rod, a dry cloth, a paper stirrup, some cotton thread and a clamp stand.
(a)Describe an experiment, using only this equipment, which shows that like charges repel, that unlike charges attract and that these forces act without contact.
[6]
- Question 11 (6 marks)Density
A metal block is a cuboid measuring 4.0 cm × 3.0 cm × 2.0 cm. Its mass is 213.6 g.
(a)Write down the equation that links density, mass and volume.
[1](b)Calculate the volume of the block in cm³.
[1](c)Calculate the density of the metal in kg/m³.
[3](d)The densities of four metals are: aluminium 2700 kg/m³, iron 7900 kg/m³, copper 8900 kg/m³, lead 11 300 kg/m³. Which metal is the block most likely to be made of?
[1]
- Question 12 (6 marks)Particle motion in gases
A student seals some air inside a glass flask and stands the flask in a water bath. The student changes the temperature of the water and reads the pressure of the air from a sensor each time. Results: 20 °C, 101 kPa; 40 °C, 108 kPa; 60 °C, 115 kPa; 80 °C, 122 kPa.
(a)Describe the pattern shown by the results.
[1](b)Give one control variable in this investigation.
[1](c)Suggest why the student waits for a few minutes after changing the water temperature before taking each reading.
[1](d)Predict the pressure of the air at 100 °C.
[1](e)The student plots a graph of pressure on the y-axis against temperature in °C on the x-axis. Describe the shape of the graph.
[2]
- Question 13 (7 marks)Pressure in gasesPhysics only
GCSE Physics only. A student traps some air in a sealed syringe connected to a pressure gauge. The student moves the plunger to change the volume, keeping the temperature constant. Results: 50 cm³, 100 kPa; 40 cm³, 125 kPa; 25 cm³, 200 kPa; 20 cm³, 250 kPa.
(a)Use the results to show that pressure × volume is constant.
[2](b)Calculate the volume of the air when the pressure is 160 kPa.
[2](c)Suggest how the student can keep the temperature of the air constant.
[1](d)Describe the shape of a graph of pressure (y-axis) against volume (x-axis) for these results.
[2]
- Question 14 (1 mark)Structure of the atom
A textbook shows a simple model of a helium atom. Two protons and two neutrons are drawn close together at the centre. Two electrons are drawn further out. The caption says the model is not to scale.
(a)Name the part of the atom made up of the protons and neutrons.
[1]
- Question 15 (6 marks)Structure of the atom
A typical atom has a radius of 1 × 10⁻¹⁰ m. The radius of a nucleus is less than 1/10 000 of the radius of its atom.
(a)Write 1/10 000 in standard form.
[1](b)Calculate the largest radius that the nucleus of this atom could have.
[2](c)An iron atom has a radius of 1.3 × 10⁻¹⁰ m. Its nucleus has a radius of 4.6 × 10⁻¹⁵ m. Calculate how many times greater the radius of the atom is than the radius of the nucleus. Give your answer in standard form to 2 significant figures.
[3]
- Question 16 (8 marks)Radioactive decay and nuclear radiation
A student places different absorbers between a radioactive source and a Geiger–Müller tube. The background count rate has been subtracted from each reading. No absorber: 480 counts per minute. One sheet of paper: 471 counts per minute. 5 mm of aluminium: 2 counts per minute.
(a)Which type of radiation does the source emit? Explain how the data show this.
[3](b)The student repeats the reading with no absorber and gets 466 counts per minute. Suggest why the two readings are different.
[1](c)Calculate the count rate with no absorber in counts per second.
[2](d)Describe how a beta particle is produced.
[2]
- Question 17 (8 marks)Nuclear equations
Cobalt-60, ⁶⁰₂₇Co, is used to sterilise medical equipment. A cobalt-60 nucleus decays by beta emission, forming a nucleus of nickel (Ni). The nickel nucleus then gives out gamma rays.
(a)Describe how the beta particle is formed.
[2](b)Write a balanced nuclear equation for the beta decay of cobalt-60.
[3](c)State what happens to the mass number and the atomic number of the nickel nucleus when it gives out the gamma rays.
[1](d)Explain why the beta decay produces a different element, but the gamma emission does not.
[2]
End of practice paper · 100 marks in total
Mark schemeOpen it only after you have finished the paper.ShowHide
Question 1 (4 marks)
(a)0.1 °C [1]
- 0.1 °C
(b)Q has a systematic (zero) error: it reads 1.4 °C above the true value. Resolution is only the smallest change Q can show; it does not bring the readings closer to the true value. [2]
- Q reads 1.4 °C above the true value (a zero / systematic error)
- Better resolution only means smaller changes can be shown; it does not make readings closer to the true value
(c)37.9 − 1.4 = 36.5 °C [1]
- 36.5 °C
Revise: Accuracy, precision and errors · Accuracy, precision and errors simulation
Question 2 (5 marks)
(a)Δθ = 65 − 15 = 50 °C. ΔE = 120 × 880 × 50 = 5 280 000 J (5.28 MJ) [3]
- Δθ = 50 °C
- ΔE = 120 × 880 × 50
- ΔE = 5 280 000 J (accept 5.28 MJ)
(b)A large mass with a high specific heat capacity stores a lot of energy for each degree of temperature rise. So the heater can store plenty of energy overnight without becoming dangerously hot, and releases it as it cools during the day. [2]
- More energy is stored for each °C rise (ΔE = m c Δθ is larger for large m and c).
- So a lot of energy is stored without a very high temperature, and is released slowly as the blocks cool.
Revise: Specific heat capacity · Specific heat capacity simulation
Question 3 (8 marks)
(a)useful output = efficiency × total input = 0.30 × 1.5 MJ = 0.45 MJ (450 000 J) [2]
- useful output = 0.30 × 1.5 (MJ)
- = 0.45 MJ (450 000 J)
(b)Lubricate the engine's moving parts: this cuts friction, meaning less energy is wasted heating the engine. Streamline the body of the car: this reduces air resistance, so less work is done against it and less energy is dissipated. [4]
- Lubricate the moving parts (of the engine).
- This cuts friction, meaning less energy is wasted heating the engine.
- Streamline the car body (allow any other valid change).
- This reduces air resistance, so less work is done against it.
(c)Some energy is always dissipated, for example by friction heating the engine and as sound. Therefore less energy comes out usefully than goes in. [2]
- Some of the input energy is always dissipated (e.g. heating the engine and surroundings, or as sound).
- Therefore less energy comes out usefully than is put in.
Question 4 (5 marks)
(a)Any two of coal, natural gas and nuclear fuel. [2]
- One of coal / natural gas / nuclear fuel
- A second, different one of coal / natural gas / nuclear fuel
(b)A resource that is naturally replaced at the rate it is used, so it will not run out. [1]
- It is replaced (naturally) as it is used (allow: it will not run out)
(c)Biofuel, such as bioethanol or biodiesel. [1]
- Biofuel (allow: electricity generated from a named renewable resource, used to charge electric vehicles)
(d)Very few places in the UK have hot rocks close enough to the surface. [1]
- Few suitable sites / hot rocks are rarely close enough to the surface in the UK
Revise: Energy resources · Energy resources simulation
Question 5 (8 marks)
(a)Place the clips 50 cm apart. Connect the ammeter in series with the wire and the supply, and the voltmeter in parallel across the 50 cm section. Switch on and record both readings. Calculate R = V ÷ I. [4]
- Clips placed 50 cm apart, measured with the ruler.
- Ammeter in series with the wire.
- Voltmeter in parallel across the length of wire being tested.
- Resistance calculated using R = V ÷ I.
(b)R = 1.8 ÷ 0.45 = 4.0 Ω [2]
- R = 1.8 ÷ 0.45
- R = 4.0 Ω
(c)The current heats the wire. A rise in temperature would increase the resistance, so length would not be the only variable changing. [2]
- The current causes the wire to heat up.
- Higher temperature increases resistance, so the test would not be fair (temperature must stay constant).
Revise: Current, resistance and potential difference · Circuit builder simulation
Question 6 (6 marks)
(a)V = IR [1]
- V = IR
(b)R = V ÷ I = 9.0 ÷ 0.36 = 25 Ω [2]
- 9.0 = 0.36 × R or R = 9.0 ÷ 0.36
- R = 25 Ω
(c)At 9.0 V the current is larger, so the filament is at a higher temperature. A hotter metal filament has a greater resistance. [2]
- A larger current makes the filament hotter (its temperature is higher).
- A hotter filament has a greater resistance.
(d)It has the same shape: each p.d. gives a current of equal size flowing the other way, so the curve for negative values is the positive curve rotated by 180° around the origin. [1]
- Same shape (equal-sized current, opposite direction, for each p.d.; accept rotational symmetry about the origin).
Revise: I–V characteristics · I–V characteristics simulation
Question 7 (5 marks)
(a)R total = 20 + 30 = 50 Ω [1]
- 50 Ω
(b)I = V ÷ R = 12 ÷ 50 = 0.24 A [2]
- I = 12 ÷ 50
- I = 0.24 A
(c)V = I R = 0.24 × 30 = 7.2 V [2]
- V = 0.24 × 30 (allow their current from the previous part)
- V = 7.2 V
Revise: Series and parallel circuits · Circuit builder simulation
Question 8 (5 marks)
(a)Direct potential difference (d.c.). [1]
- direct (allow d.c.)
(b)The mains p.d. is alternating: it reverses its direction many times each second. The battery's p.d. is direct: it always acts in the same direction, so its current flows one way only. [2]
- the mains p.d. keeps reversing direction / is alternating
- the battery's p.d. always acts in the same direction / is direct
(c)Frequency: 50 Hz. Potential difference: about 230 V. [2]
- 50 Hz
- (about) 230 V
Revise: Mains electricity · Mains electricity and safety simulation
Question 9 (6 marks)
(a)efficiency = useful power output ÷ total power input = 497 ÷ 500 = 0.994 (99.4%) [2]
- efficiency = 497 ÷ 500
- 0.994 (accept 99.4%)
(b)It heats the cables and is dissipated to the surroundings. [1]
- It heats the cables (and is dissipated to the surroundings).
(c)The efficiency decreases. At a lower p.d., the current needed for the same power is larger. A larger current heats the cables more, so more energy is wasted. [3]
- The efficiency decreases.
- The current is larger (for the same power).
- More heating of the cables, so more energy is dissipated (wasted).
Revise: The National Grid · Transformers and the National Grid simulation
Question 10 (6 marks)
(a)Rub one polythene rod with the cloth so that it gains electrons and becomes negative. Put it in the paper stirrup, hung by the thread from the clamp stand, so that it can turn freely. Rub the second polythene rod and hold it near one end of the hanging rod without touching it: the hanging rod turns away, showing that like charges repel. Rub the acetate rod, which loses electrons and becomes positive, and hold it near the same end: the hanging rod turns towards it, showing that unlike charges attract. The rods never touch, so the forces are non-contact. (Six-mark questions are marked by level of response: the whole answer is read and put into a level. To reach the top level, give a workable method in a logical order and link each observation to the rule it shows.) [6]
- Rub a polythene rod with the cloth (it gains electrons and becomes negative).
- Hang it in the paper stirrup on the thread from the clamp stand, so that it can turn freely.
- Rub the second polythene rod and hold it near one end of the hanging rod, without touching.
- The hanging rod turns away: both are negative, so like charges repel.
- Rub the acetate rod (it loses electrons and becomes positive) and hold it near, without touching.
- The hanging rod turns towards it: unlike charges attract; the rods never touch, so the forces are non-contact.
Revise: Static electricity and electric fields · Static electricity and electric fields simulation
Question 11 (6 marks)
(a)density = mass ÷ volume (ρ = m ÷ V) [1]
- density = mass ÷ volume
(b)V = 4.0 × 3.0 × 2.0 = 24 cm³ [1]
- 24 cm³
(c)ρ = 213.6 ÷ 24 = 8.9 g/cm³ = 8900 kg/m³ (or 0.2136 kg ÷ 2.4 × 10⁻⁵ m³ = 8900 kg/m³) [3]
- ρ = 213.6 ÷ 24 (allow their volume)
- 8.9 g/cm³, or converting to 0.2136 kg and 2.4 × 10⁻⁵ m³
- 8900 kg/m³
(d)Copper [1]
- Copper (allow the metal matching their calculated density)
Revise: Density · Measuring density simulation
Question 12 (6 marks)
(a)As the temperature of the air increases, its pressure increases (by about 7 kPa for every 20 °C). [1]
- The pressure increases as the temperature increases.
(b)The volume of the air (the same flask is used), or the mass of air (the flask stays sealed). [1]
- Volume of the air / mass of the air.
(c)So that the air inside the flask has time to reach the same temperature as the water. [1]
- To let the air reach the temperature of the water.
(d)129 kPa (the pressure goes up by about 7 kPa for each 20 °C). [1]
- 129 kPa (accept 128–130 kPa).
(e)A straight line that slopes upwards. It does not pass through the origin, because the pressure at 0 °C is not zero. [2]
- A straight line with a positive gradient (sloping upwards).
- It does not pass through the origin (the pressure at 0 °C is about 94 kPa, not zero).
Revise: Particle motion in gases · Gas laws and particles simulation
Question 13 (7 marks)
(a)50 × 100 = 5000; 40 × 125 = 5000; 25 × 200 = 5000; 20 × 250 = 5000. Every product is 5000 kPa cm³. [2]
- At least two products of pressure × volume calculated correctly.
- All four products are 5000 kPa cm³, so pressure × volume is constant.
(b)V = 5000 ÷ 160 = 31.25 cm³, about 31 cm³ [2]
- V = 5000 ÷ 160
- V = 31 cm³ (accept 31.25 cm³)
(c)Move the plunger slowly and wait before each reading, so the air has time to return to room temperature. [1]
- Move the plunger slowly / wait before reading the gauge each time.
(d)A curve in which the pressure decreases as the volume increases. It falls steeply at small volumes and becomes less steep at large volumes, without touching either axis. [2]
- A curve: pressure decreases as volume increases.
- Steep at small volumes and flattening at larger volumes (not a straight line).
Revise: Pressure in gases · Gas laws and particles simulation
Question 14 (1 mark)
(a)The nucleus. [1]
- Nucleus
Revise: Structure of the atom · Isotopes and atom builder simulation
Question 15 (6 marks)
(a)1 × 10⁻⁴ [1]
- 1 × 10⁻⁴
(b)1 × 10⁻¹⁰ × 1 × 10⁻⁴ = 1 × 10⁻¹⁴ m [2]
- 1 × 10⁻¹⁰ ÷ 10 000 (or × 1 × 10⁻⁴)
- 1 × 10⁻¹⁴ m
(c)1.3 × 10⁻¹⁰ ÷ 4.6 × 10⁻¹⁵ = 28 000 (28 261), so about 2.8 × 10⁴ times [3]
- Dividing the atom's radius by the nucleus's radius: 1.3 × 10⁻¹⁰ ÷ 4.6 × 10⁻¹⁵
- = 28 261 (allow 28 000)
- 2.8 × 10⁴ (standard form, 2 significant figures)
Revise: Structure of the atom · Isotopes and atom builder simulation
Question 16 (8 marks)
(a)Beta. Paper makes almost no difference, so the source does not emit alpha. The aluminium brings the count rate down to almost zero, so there is no gamma; beta is the radiation that passes paper but is absorbed by a few millimetres of aluminium. [3]
- Beta (only)
- Paper hardly changes the count rate, so no alpha
- Aluminium reduces it to (almost) zero, so no gamma / radiation stopped by aluminium is beta
(b)Radioactive decay is random, so the number of counts varies from one measurement to the next. [1]
- Radioactive decay is random
(c)480 ÷ 60 = 8 counts per second [2]
- 480 ÷ 60
- 8 counts per second
(d)A neutron in the nucleus turns into a proton. A high-speed electron is ejected from the nucleus: this is the beta particle. [2]
- A neutron (in the nucleus) changes into a proton
- A high-speed electron is emitted from the nucleus
Revise: Radioactive decay and nuclear radiation · Alpha, beta and gamma radiation simulation
Question 17 (8 marks)
(a)One of the neutrons in the cobalt nucleus becomes a proton. An electron is produced at the same time and shot out of the nucleus at high speed; that electron is the beta particle. [2]
- A neutron becomes a proton (in the nucleus)
- An electron is emitted from the nucleus at high speed
(b)⁶⁰₂₇Co → ⁶⁰₂₈Ni + ⁰₋₁e [3]
- Beta particle shown as ⁰₋₁e
- Nickel with mass number 60
- Nickel with atomic number 28
(c)Neither changes: they stay at 60 and 28. [1]
- Both stay the same
(d)The element is fixed by the atomic number, the number of protons. Beta decay raises it from 27 to 28. Gamma rays have no charge, so after they leave, the atomic number is still 28. [2]
- The element depends on the atomic number / number of protons
- Beta decay changes the atomic number (27 to 28) but gamma emission does not