What AQA asks for: spec points 4.1.1.3 and 4.3.2.2
Specific heat capacity appears twice in the AQA specification, under energy and under the particle model. It is on both tiers, in GCSE Physics and in Combined Science. You should be able to:
- explain that a system's temperature rise depends on its mass, its material and the energy put in
- use , which is given on the Physics equation sheet: pick it out and apply it rather than memorise it
- define specific heat capacity
- describe Required practical 1, which links the energy supplied to a material with its rise in temperature. Combined Science students do the same practical, but their specification gives it a different number.
The equation
is the change in thermal energy in joules (J), the mass in kilograms (kg), the specific heat capacity in joules per kilogram per degree Celsius (J/kg °C), and the temperature change in degrees Celsius (°C).
The specific heat capacity of a substance is the energy needed to raise the temperature of 1 kg of it by 1 °C. Water's is high, about 4200 J/kg °C. Aluminium's is about 900 J/kg °C and copper's about 390 J/kg °C, so the same energy warms a kilogram of copper nearly eleven times as much as a kilogram of water.
Worked example 1: a hot-water bottle. How much energy warms 0.80 kg of water from 15 °C to 60 °C? Use J/kg °C.
Given: kg, J/kg °C, °C. Equation: . Substitution: . Answer: J, about 150 kJ (2 s.f.).
Worked example 2: practical data. A 40 W heater warms a 0.80 kg copper block for 5.0 minutes, and its temperature rises from 21.0 °C to 56.0 °C. Find the specific heat capacity of copper.
Energy supplied: from , which you must recall, J. Temperature change: °C. Equation: rearrange to . Substitution: . Answer: J/kg °C (2 s.f.).
That is above the data-book value. Some energy warmed the surroundings instead of the block, so the temperature rise was smaller than it should have been, and dividing by too small a gives too large a .
Required practical 1
A common version uses a 1 kg aluminium block with two holes: one for an electric immersion heater, one for a thermometer.
- Measure the block's mass on a balance and wrap it in insulation.
- Put the heater in its hole and the thermometer in the other. A few drops of water in the thermometer hole give good thermal contact.
- Connect the heater to a power supply through a joulemeter, or use an ammeter and a voltmeter to work out its power.
- Record the starting temperature, then switch on and start a stopwatch.
- Record the temperature and the energy supplied every minute for about 10 minutes.
- Plot temperature against energy supplied. The straight section has gradient , so .
The reading often creeps up briefly after the heater is switched off, so look for the highest value.
Using the simulation
In the simulation above, a 1.00 kg Aluminium block has a 50 W heater, Lagged insulation and a 10 min Heater timer. The button already reads Heater on, so just press Play. A reading enters the Results table every minute. At 600 s the timer switches the heater off, with 30000 J supplied and the thermometer at 51.6 °C, but it still peaks at 52.2 °C. From the gradient of the line gives 928 J/(kg °C) and From the first reading and the highest temperature gives 932 J/(kg °C), both a little above the accepted 900. J/(kg °C) means the same as AQA's J/kg °C.
Set Insulation to None and run again: more energy is Dissipated to the surroundings, and both results rise above 1000 J/(kg °C). With No losses, both come out at about 900. Then pick Water in a beaker: the same 30000 J warms it by only about 7 °C.