Skip to content

An original Labverse practice paper — not an official exam paper

GCSE Physics — AQA

AQA GCSE Physics Paper 1 practice paper C

Written by Labverse from our own exam-style questions, to the same time and total marks as AQA’s Paper 1 (8463/1F, 8463/1H), on the same topics. It is not set, checked or endorsed by AQA.

Time allowed
1 hour 45 minutes
Total marks
100
Questions
15
Level
All tiers

Instructions

  • Answer every question. Work in one sitting and stop when the time is up.
  • The marks for each part are shown beside it. Use them to judge how much to write.
  • Show your working for calculations and give the unit with every answer.

To print the answers too, open the mark scheme at the end first.

Marks by topic

  • Working scientifically · 7 marks
  • Energy · 24 marks
  • Electricity · 31 marks
  • Particle model of matter · 19 marks
  • Atomic structure · 19 marks

Questions

  1. Question 1 (7 marks)Measuring instruments

    A technician uses Vernier callipers to measure the outside diameter of a plastic pipe. The main scale is marked in millimetres. Each division on the vernier scale is worth 0.1 mm.

    1. (a)The vernier zero is just past the 32 mm mark on the main scale, and vernier line 7 lines up with a main-scale mark. Give the reading on the callipers.

      [2]
    2. (b)With the jaws closed and nothing between them, the callipers read 0.2 mm. Name this type of error.

      [1]
    3. (c)Calculate the true diameter of the pipe.

      [2]
    4. (d)Explain why measuring the pipe several more times and calculating a mean would not remove this error.

      [2]
  2. Question 2 (7 marks)Specific heat capacity

    A chef heats 0.60 kg of olive oil in a pan from 20 °C to 170 °C. Specific heat capacity of the oil = 1970 J/kg °C.

    1. (a)Calculate the energy transferred to the oil.

      [3]
    2. (b)The hob supplies energy at a rate of 1500 W. Assume that all of this energy goes into the oil. Calculate the time taken to heat the oil.

      [2]
    3. (c)In practice, heating the oil takes longer than this. Suggest why.

      [2]
  3. Question 3 (10 marks)Specific heat capacity

    A student wants to determine the specific heat capacity of aluminium. The student has a 1.0 kg aluminium block with two holes, an immersion heater, a thermometer, a joulemeter, a power supply, a stopwatch and some insulating material.

    1. (a)Describe a method the student could use.

      [6]
    2. (b)Explain why the student puts a few drops of water in the thermometer hole.

      [2]
    3. (c)The student's value for the specific heat capacity of aluminium is higher than the accepted value. Explain why.

      [2]
  4. Question 4 (7 marks)Energy resources

    Typical whole-life carbon dioxide emissions for electricity are given below. They are approximate values. Coal: 820 g per kWh. Natural gas: 490 g per kWh. Nuclear fuel: 12 g per kWh. Wind: 11 g per kWh. 1 tonne = 1 000 000 g.

    1. (a)A gas-fired power station generates 5 000 000 kWh of electricity in one day. Calculate the mass of carbon dioxide linked to this electricity. Give your answer in tonnes.

      [3]
    2. (b)Calculate how much less carbon dioxide would be linked to the same amount of electricity if it were generated by wind turbines.

      [2]
    3. (c)Nuclear power stations are linked to very little carbon dioxide. Give one environmental disadvantage of nuclear power.

      [1]
    4. (d)Suggest why the whole-life figure for wind turbines is not zero.

      [1]
  5. Question 5 (6 marks)Circuit symbols

    A student sets up a circuit to find the resistance of a filament lamp. The circuit contains a battery, a closed switch, the lamp, an ammeter and a voltmeter.

    1. (a)The lamp symbol is drawn on the circuit diagram. Describe what the lamp symbol looks like.

      [1]
    2. (b)Describe how the ammeter and the voltmeter should be connected in the circuit.

      [2]
    3. (c)The ammeter reads 0.40 A and the voltmeter reads 2.4 V. Calculate the resistance of the lamp. Give the unit.

      [3]
  6. Question 6 (9 marks)I–V characteristics

    A student has a fixed resistor, a battery, a switch, a variable resistor, an ammeter, a voltmeter and connecting leads. The student wants to find the I–V characteristic of the resistor.

    1. (a)Describe a method the student could use. Include how to get readings for negative values of potential difference.

      [6]
    2. (b)Explain why the student should open the switch between readings.

      [2]
    3. (c)The student's best-fit line is straight and goes through the origin. What does this tell you about the resistor?

      [1]
  7. Question 7 (5 marks)I–V characteristics

    A resistor is kept at constant temperature. Its I–V graph, with current on the vertical axis, is straight and passes through the origin. One point on the line is at a potential difference of 6.0 V and a current of 0.12 A.

    1. (a)Calculate the gradient of the line.

      [2]
    2. (b)Use your answer to calculate the resistance of the resistor.

      [2]
    3. (c)A second resistor has a larger resistance. State how its I–V graph would differ from the first one.

      [1]
  8. Question 8 (5 marks)LDRs and thermistors

    A thermistor is used to control the heater in a tropical fish tank.

    1. (a)Describe how the resistance of the thermistor changes as the temperature of the water increases.

      [1]
    2. (b)The potential difference across the thermistor is 4.0 V and the current through it is 0.0020 A. Calculate its resistance.

      [2]
    3. (c)The water cools down. The potential difference across the thermistor stays the same. Explain what happens to the current in the thermistor.

      [2]
  9. Question 9 (6 marks)Energy transfers in appliances

    Boiling the water in a kettle needs 336 kJ of energy to be transferred to the water.

    1. (a)A 2.8 kW kettle is used. Calculate the shortest time it could take to transfer 336 kJ.

      [3]
    2. (b)A travel kettle has a power rating of 1.2 kW. Explain why it takes longer to boil the same water.

      [2]
    3. (c)In practice, the 2.8 kW kettle takes longer than the time you calculated. Suggest why.

      [1]
  10. Question 10 (5 marks)Changes of state

    Changes of state happen in many everyday situations.

    1. (a)Name the change of state in each situation: (i) wet clothes drying on a washing line; (ii) droplets forming on a cold window; (iii) dry ice (solid carbon dioxide) turning straight into a gas.

      [3]
    2. (b)Give two differences between boiling and evaporating.

      [2]
  11. Question 11 (8 marks)Specific latent heat

    Steam at 100 °C from a kettle condenses on a person's hand. Specific latent heat of vaporisation of water = 2.26 × 10⁶ J/kg. Specific heat capacity of water = 4200 J/kg °C.

    1. (a)Name the change of state when steam turns into water.

      [1]
    2. (b)Calculate the energy released when 2.0 g of steam at 100 °C condenses to water at 100 °C.

      [3]
    3. (c)The water then cools from 100 °C to 35 °C on the skin. Calculate the energy released as it cools.

      [2]
    4. (d)Use your answers to explain why a scald from steam at 100 °C is much worse than one from the same mass of water at 100 °C.

      [2]
  12. Question 12 (6 marks)Particle motion in gases

    An oxygen molecule has a mass of 5.3 × 10⁻²⁶ kg. In a sample of oxygen at room temperature, one molecule is moving at 650 m/s while another is moving at 300 m/s.

    1. (a)Calculate how much kinetic energy the faster molecule has. Give your answer in standard form.

      [2]
    2. (b)Describe the motion of the molecules in the sample of oxygen.

      [2]
    3. (c)Suggest why the molecules in the same sample do not all move at the same speed.

      [1]
    4. (d)The oxygen is warmed. State what happens to the average kinetic energy of its molecules.

      [1]
  13. Question 13 (7 marks)Mass number and isotopes

    A student is given data about three neutral atoms. Atom 1 has 17 protons and 18 neutrons. Atom 2 has 17 protons and 20 neutrons. Atom 3 has 18 protons and 22 neutrons.

    1. (a)Give the mass number of atom 1.

      [1]
    2. (b)Which two atoms are isotopes of the same element? Give a reason for your answer.

      [2]
    3. (c)Explain why atom 2 has no overall charge.

      [2]
    4. (d)Atom 3 has a larger mass number than atom 1. A student says that atom 3 must be a heavier isotope of the same element as atom 1. Explain why the student is wrong.

      [2]
  14. Question 14 (6 marks)Nuclear equations

    Each of these two nuclear equations has one particle missing. Equation 1: ²¹⁴₈₂Pb → ²¹⁴₈₃Bi + X. Equation 2: ²³⁹₉₄Pu → ²³⁵₉₂U + Y.

    1. (a)Determine the mass number and the atomic number of particle X.

      [2]
    2. (b)Name particle X.

      [1]
    3. (c)Identify particle Y. Show how the numbers in Equation 2 lead to your answer.

      [3]
  15. Question 15 (6 marks)Contamination and irradiation

    Strawberries are passed close to a cobalt-60 source so that gamma rays kill bacteria on and inside the fruit. This helps the strawberries to stay fresh for longer.

    1. (a)A customer says the strawberries will now be radioactive. Explain why the customer is wrong.

      [2]
    2. (b)Suggest why the fruit is treated with gamma rays instead of alpha particles.

      [2]
    3. (c)Give two precautions that protect the people who work at the treatment plant.

      [2]

End of practice paper · 100 marks in total

Mark schemeOpen it only after you have finished the paper.Show
  1. Question 1 (7 marks)

    1. (a)32 mm + 7 × 0.1 mm = 32.7 mm [2]

      • 32 + 7 × 0.1
      • 32.7 mm
    2. (b)A zero error, which is a type of systematic error. [1]

      • Zero error / systematic error
    3. (c)true diameter = 32.7 − 0.2 = 32.5 mm [2]

      • 32.7 − 0.2 (allow their reading from the first part)
      • 32.5 mm
    4. (d)The zero error makes every reading too large by the same amount, 0.2 mm. The mean of readings that are all 0.2 mm too large is also 0.2 mm too large; averaging only reduces random error. [2]

      • The error shifts every reading by the same amount in the same direction.
      • So the mean is shifted by the same amount (a mean only reduces the effect of random errors).

    Revise: Measuring instruments · Vernier caliper simulation

  2. Question 2 (7 marks)

    1. (a)Δθ = 170 − 20 = 150 °C. ΔE = m c Δθ = 0.60 × 1970 × 150 = 177 300 J (about 177 000 J) [3]

      • Δθ = 150 °C
      • ΔE = 0.60 × 1970 × 150
      • ΔE = 177 300 J (accept 177 000 J or 177 kJ)
    2. (b)t = E ÷ P = 177 300 ÷ 1500 = 118 s [2]

      • t = 177 300 ÷ 1500 (allow their energy)
      • t = 118 s (accept 120 s)
    3. (c)Some of the energy from the hob heats the pan and the surrounding air instead of the oil. So less than 1500 W goes into the oil, and it takes longer to transfer 177 300 J to it. [2]

      • Energy is dissipated / transferred to the pan and the surroundings (not all goes to the oil).
      • So the rate of energy transfer to the oil is less than 1500 W, and the oil heats more slowly.

    Revise: Specific heat capacity · Specific heat capacity simulation

  3. Question 3 (10 marks)

    1. (a)Check the mass of the block on a balance. Wrap the block in the insulating material. Put the heater in one hole and the thermometer in the other, with a little water in the thermometer hole for good thermal contact. Connect the heater to the power supply through the joulemeter. Record the starting temperature and the joulemeter reading. Switch on and record the temperature and the joulemeter reading every minute for about 10 minutes. Calculate the temperature rise and use c = ΔE ÷ (m Δθ), or plot temperature against energy supplied and use c = 1 ÷ (m × gradient). (AQA marks 6-mark questions as a whole, by level of response. The marking points below show what a top-level answer covers.) [6]

      • Mass of the block measured (or 1.0 kg used) and the block wrapped in insulation.
      • Heater placed in one hole and the thermometer in the other (with water for good thermal contact).
      • Heater connected to the power supply through the joulemeter.
      • Starting temperature recorded, then temperature and energy recorded at regular intervals (for example every minute for 10 minutes).
      • Temperature rise calculated from the starting and highest temperatures.
      • c calculated using c = ΔE ÷ (m Δθ), or from the gradient of a graph of temperature against energy supplied.
    2. (b)The water fills the air gap between the thermometer and the metal, giving good thermal contact. So the thermometer reads the temperature of the block more accurately. [2]

      • Improves thermal contact between the thermometer and the block (air is a poor conductor).
      • So the thermometer reading is closer to the block's actual temperature.
    3. (c)Some of the energy supplied is dissipated to the surroundings instead of heating the block. The temperature rise is therefore smaller than expected, and dividing by a smaller temperature rise gives a larger value of c. [2]

      • Energy is dissipated / lost to the surroundings (not all of it heats the block).
      • So the temperature rise is smaller, which gives a larger calculated value of c.

    Revise: Specific heat capacity · Specific heat capacity simulation

  4. Question 4 (7 marks)

    1. (a)Mass = 5 000 000 × 490 = 2 450 000 000 g. Dividing by 1 000 000 gives 2450 tonnes. [3]

      • 5 000 000 × 490
      • 2 450 000 000 g
      • 2450 tonnes
    2. (b)Wind: 5 000 000 × 11 = 55 000 000 g = 55 tonnes. Difference = 2450 − 55 = 2395 tonnes (about 2400 tonnes). [2]

      • Wind: 55 tonnes (55 000 000 g) (allow 5 000 000 × (490 − 11))
      • 2395 tonnes (allow 2400 tonnes; allow their value from the part above)
    3. (c)It produces radioactive waste, which stays dangerous for thousands of years and needs secure storage. [1]

      • Radioactive waste (that must be stored for a very long time) (allow: an accident could release radioactive material)
    4. (d)Energy from fuels is used to make the steel and concrete and to transport and build the turbines. [1]

      • Carbon dioxide is released when the turbines are made, transported or installed (or dismantled)

    Revise: Energy resources · Energy resources simulation

  5. Question 5 (6 marks)

    1. (a)A circle with a cross inside it. [1]

      • Circle with a cross (X) drawn inside it.
    2. (b)The ammeter is in series with the lamp. The voltmeter is in parallel across the lamp. [2]

      • Ammeter connected in series with the lamp.
      • Voltmeter connected in parallel with (across) the lamp.
    3. (c)R = V ÷ I = 2.4 ÷ 0.40 = 6.0 Ω [3]

      • 2.4 = 0.40 × R or R = 2.4 ÷ 0.40
      • R = 6.0 (accept 6)
      • Unit: Ω (ohms)

    Revise: Circuit symbols · Circuit builder simulation

  6. Question 6 (9 marks)

    1. (a)Join the battery, switch, variable resistor, ammeter and fixed resistor in series, and connect the voltmeter in parallel across the fixed resistor only. Close the switch, adjust the variable resistor for a low p.d., read both meters, then open the switch. Change the variable resistor to obtain at least five different p.d.s, recording the current and the p.d. each time. Reverse the connections to the fixed resistor (or to the battery) and repeat, recording these readings as negative. Repeat each reading and calculate a mean current. Plot current on the vertical axis against p.d. on the horizontal axis and draw a line of best fit. (Level-of-response marking: the answer is judged as a whole. Level 3, 5–6 marks: a clear, logically ordered method that would give valid results, covering meter positions, changing the p.d., negative values and repeats. Level 2, 3–4 marks: most of the steps are present, but an important step is missing or the order is unclear. Level 1, 1–2 marks: some relevant points, such as where one meter goes, but not a workable method. 0 marks: nothing worthy of credit.) [6]

      • Ammeter connected in series, and voltmeter connected in parallel, with the fixed resistor.
      • Variable resistor adjusted to change the p.d. across the resistor (and so the current).
      • Current and p.d. recorded for a range of settings (at least five).
      • Connections to the resistor (or battery) reversed to obtain negative values.
      • Each reading repeated and a mean calculated.
      • Current plotted against p.d. with a line of best fit (or: switch opened between readings so the resistor does not heat up).
    2. (b)The current heats the resistor. A change in its temperature would change its resistance, but the investigation needs the resistor at a constant temperature. [2]

      • The current causes heating in the resistor.
      • A change in temperature would change the resistance (the temperature must stay constant).
    3. (c)Its resistance does not change: the current is proportional to the p.d., so it is an ohmic conductor. [1]

      • Resistance stays the same (current proportional to p.d.; accept ohmic conductor).

    Revise: I–V characteristics · I–V characteristics simulation

  7. Question 7 (5 marks)

    1. (a)gradient = change in current ÷ change in p.d. = 0.12 ÷ 6.0 = 0.020 A/V [2]

      • gradient = 0.12 ÷ 6.0
      • gradient = 0.020 (A/V)
    2. (b)R = 1 ÷ gradient = 1 ÷ 0.020 = 50 Ω (as a check, 6.0 ÷ 0.12 = 50 Ω) [2]

      • R = 1 ÷ 0.020 (or R = 6.0 ÷ 0.12)
      • R = 50 Ω
    3. (c)Its line would be less steep (a smaller gradient), but still straight and through the origin. [1]

      • Less steep line / smaller gradient (still straight through the origin).

    Revise: I–V characteristics · I–V characteristics simulation

  8. Question 8 (5 marks)

    1. (a)The resistance decreases. [1]

      • Resistance decreases as temperature increases.
    2. (b)R = V ÷ I = 4.0 ÷ 0.0020 = 2000 Ω [2]

      • R = 4.0 ÷ 0.0020
      • R = 2000 Ω (accept 2.0 kΩ)
    3. (c)As the water cools, the thermistor's resistance increases. With the same p.d., a larger resistance means the current decreases. [2]

      • Resistance of the thermistor increases.
      • So the current decreases (for the same p.d.).

    Revise: LDRs and thermistors · Circuit builder simulation

  9. Question 9 (6 marks)

    1. (a)E = 336 000 J and P = 2800 W. t = E ÷ P = 336 000 ÷ 2800 = 120 s [3]

      • 336 000 J and 2800 W
      • t = 336 000 ÷ 2800
      • t = 120 s
    2. (b)Its lower power means it transfers fewer joules each second. The same energy is still needed, so it takes longer: at least 336 000 ÷ 1200 = 280 s. [2]

      • Lower power, so energy is transferred at a lower rate (fewer joules per second).
      • The same energy is needed, so it takes more time (allow 280 s).
    3. (c)Some energy is dissipated, warming the body of the kettle and the surrounding air, so more than 336 kJ must be transferred from the mains. [1]

      • Some energy is wasted (dissipated) to the surroundings, e.g. heating the kettle and the air.

    Revise: Energy transfers in appliances · Charge, current, energy and power simulation

  10. Question 10 (5 marks)

    1. (a)(i) Evaporating (ii) Condensing (iii) Sublimating [3]

      • (i) Evaporating / evaporation
      • (ii) Condensing / condensation
      • (iii) Sublimating / sublimation
    2. (b)Evaporating happens only at the surface of a liquid, but boiling happens throughout it, with bubbles forming inside. Evaporating happens at temperatures below the boiling point, but boiling happens only at the boiling point. [2]

      • Evaporating happens at the surface only; boiling happens throughout the liquid (bubbles form inside it).
      • Evaporating happens below the boiling point (at any temperature); boiling happens only at the boiling point.

    Revise: Changes of state · Latent heat and heating curves simulation

  11. Question 11 (8 marks)

    1. (a)Condensing (condensation) [1]

      • Condensing / condensation
    2. (b)m = 2.0 g = 0.0020 kg. E = m L = 0.0020 × 2.26 × 10⁶ = 4520 J [3]

      • m = 0.0020 kg
      • E = 0.0020 × 2.26 × 10⁶
      • E = 4520 J (accept 4500 J)
    3. (c)ΔE = m c Δθ = 0.0020 × 4200 × 65 = 546 J [2]

      • ΔE = 0.0020 × 4200 × 65
      • ΔE = 546 J (accept 550 J)
    4. (d)Water at 100 °C only releases the 546 J as it cools. Steam releases 4520 J of latent heat as it condenses, as well as the 546 J, so it transfers over nine times as much energy to the skin. [2]

      • Steam releases latent heat (4520 J) when it condenses, in addition to the energy released as the water cools.
      • So much more energy (about nine times as much in total) is transferred to the skin.

    Revise: Specific latent heat · Latent heat and heating curves simulation

  12. Question 12 (6 marks)

    1. (a)Ek = ½ m v² = 0.5 × 5.3 × 10⁻²⁶ × 650² = 1.1 × 10⁻²⁰ J [2]

      • Ek = 0.5 × 5.3 × 10⁻²⁶ × 650²
      • Ek = 1.1 × 10⁻²⁰ J
    2. (b)The molecules never stop moving, and they move in random directions, changing direction every time they collide with each other or with the container. [2]

      • Constant (continuous) motion.
      • Random motion: in all directions, changing direction in collisions.
    3. (c)They keep colliding with each other, and each collision passes energy from one molecule to another, so some end up fast and others slow. [1]

      • Collisions between molecules keep changing their speeds (passing energy between them).
    4. (d)It increases. [1]

      • It increases.

    Revise: Particle motion in gases · Gas laws and particles simulation

  13. Question 13 (7 marks)

    1. (a)17 + 18 = 35 [1]

      • 35
    2. (b)Atoms 1 and 2. They have the same number of protons (17) but different numbers of neutrons (18 and 20). [2]

      • Atoms 1 and 2
      • Same number of protons but a different number of neutrons
    3. (c)It has 17 electrons, the same as its number of protons. The negative charge of the electrons balances the positive charge of the protons. [2]

      • Number of electrons equals number of protons (17)
      • So the negative and positive charges cancel / balance
    4. (d)Atom 3 has 18 protons and atom 1 has 17. A different number of protons means a different atomic number, so atom 3 is a different element, not an isotope of the same one. [2]

      • Atom 3 has a different number of protons (18, not 17) / a different atomic number
      • So it is a different element; isotopes must have the same number of protons

    Revise: Mass number and isotopes · Isotopes and atom builder simulation

  14. Question 14 (6 marks)

    1. (a)Top: 214 − 214 = 0. Bottom: 82 − 83 = −1. X has a mass number of 0 and an atomic number of −1. [2]

      • Mass number 0
      • Atomic number (charge) −1
    2. (b)A beta particle (a high-speed electron from the nucleus). [1]

      • Beta particle (allow: electron)
    3. (c)Top: 239 − 235 = 4. Bottom: 94 − 92 = 2. A particle with mass number 4 and atomic number 2 is a helium nucleus, so Y is an alpha particle. [3]

      • Mass number of Y is 4 (239 − 235)
      • Atomic number of Y is 2 (94 − 92)
      • Y is an alpha particle / ⁴₂He

    Revise: Nuclear equations · Nuclear equations simulation

  15. Question 15 (6 marks)

    1. (a)The strawberries have been irradiated, not contaminated: no radioactive atoms have been put on or into them. So they do not give out any radiation afterwards. [2]

      • The fruit is irradiated / no radioactive atoms (material) are added to it
      • So it does not become radioactive / emits no radiation after treatment
    2. (b)Alpha particles have a very short range, so the packaging or the outside of the fruit would stop them before they reached bacteria inside. Gamma rays are very penetrating, so they pass right through the fruit. [2]

      • Alpha is stopped by the packaging / the surface of the fruit / a few cm of air
      • Gamma penetrates through the whole fruit (and its packaging)
    3. (c)Any two from: surround the source with thick concrete or lead; run the equipment by remote control from another room; limit how long anyone is near the source; give each worker a badge that records their dose, so no one goes over a safe limit. [2]

      • First precaution, e.g. shielding with thick concrete or lead
      • Second precaution, e.g. distance / remote control, limiting time, or a dose badge so no one exceeds a safe limit

    Revise: Contamination and irradiation · Alpha, beta and gamma radiation simulation