Skip to content

BISE Gujranwala · Punjab Class 9

BISE Gujranwala Annual 2021 Class 9 Physics (Objective, Group II) (5474)

Set by BISE Gujranwala for Punjab Class 9 Physics, Annual 2021: 15 minutes and 12 marks, on Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science. The paper itself is on BISE Gujranwala’s website; this page adds what it covers, how to use it and original practice questions on the same topics.

Paper facts

Series
Annual 2021
Paper
Objective, Group II
Set by
BISE Gujranwala
Code
5474
Tier
Not tiered
Time
15 minutes
Marks
12
Calculator
Not recorded here: check the paper’s instructions
Syllabus
Old Punjab syllabus (PCTB Physics 9 used until the 2024-25 session), not the NC 2023 book. Some questions, such as satellites and heat transfer, are not in the new course.
Links checked
17 November 2026

Official files

These files belong to BISE Gujranwala. Labverse links to them and never hosts or copies them. Labverse is not affiliated with BISE Gujranwala.

What this paper covers

8 topic groups from our map of Punjab Board Class 9 Physics. Revise each one with its topic pages and simulations before you sit the paper.

How to use this paper

  1. 1. Time it. Set 15 minutes for 12 marks: about 75 seconds a mark. At 8 minutes you should be roughly halfway through the marks; if you’re well behind, speed up on the short questions.
  2. 2. Sit it in one go. Open the question paper on BISE Gujranwala’s website (the link above) and work on paper, with no notes.
  3. 3. Mark it with the official scheme. The mark scheme isn’t public, so check answers with your teacher, and use the marking points on our questions below to practise marking.
  4. 4. Learn from the marks you lost. For every lost mark, note whether it was knowledge, method, reading the question or time.
  5. 5. Log mistakes by topic. Keep one line per topic group (Physical quantities and measurements, Kinematics, Dynamics, Turning effects of force, Work, energy and power, Mechanical properties of matter, Thermal properties of matter, Nature of science) and add a tally each time a mark goes there.
  6. 6. Revisit, then redo. Work through the weakest group’s topic pages and simulations, try the questions below, and come back to the paper in a week.

Practise the same topics

7 original exam-style questions on this paper’s topics, written in the style of Punjab board exams (not taken from the paper). Try each one before you reveal the answer.

  1. 1.A student uses a screw gauge (least count 0.01 mm) to measure the diameter of a knitting needle. With the jaws closed, the zero of the circular scale is 3 divisions below the horizontal line.

    From the topic: Micrometer screw gauge

    1. (a)Calculate the zero error and state whether it is added to or subtracted from the observed reading.

      2 marks
      Show the answer

      Answer: Zero error = 3 × 0.01 mm = 0.03 mm. The zero is below the line, so the gauge reads too much and the zero error is subtracted.

      Marking points

      • 3 × 0.01 = 0.03 mm
      • Subtracted (zero below the line reads too much)
    2. (b)On the needle, the main scale reading is 2.5 mm and the 19th circular division is on the horizontal line. Find the observed reading.

      2 marks
      Show the answer

      Answer: Observed reading = 2.5 mm + (19 × 0.01 mm) = 2.5 + 0.19 = 2.69 mm.

      Marking points

      • 2.5 + 19 × 0.01
      • 2.69 mm
    3. (c)Find the true diameter of the needle.

      1 mark
      Show the answer

      Answer: True diameter = 2.69 mm − 0.03 mm = 2.66 mm.

      Marking points

      • 2.69 − 0.03 = 2.66 mm
  2. 2.Two cars, P and Q, leave a toll plaza on the M-2 at the same moment and travel in the same direction. Their distance–time graphs are straight lines from the origin. P reaches 600 m at 30 s and Q reaches 600 m at 50 s.

    From the topic: Distance–time graphs

    1. (a)Which car has the steeper line on the graph?

      1 mark
      Show the answer

      Answer: Car P

      Marking points

      • Car P
    2. (b)Calculate the speed of each car.

      2 marks
      Show the answer

      Answer: P: 600 ÷ 30 = 20 m s⁻¹. Q: 600 ÷ 50 = 12 m s⁻¹.

      Marking points

      • P = 20 m s⁻¹
      • Q = 12 m s⁻¹
    3. (c)How far apart are the two cars at 30 s?

      2 marks
      Show the answer

      Answer: At 30 s, Q has covered 12 × 30 = 360 m, so the gap is 600 − 360 = 240 m.

      Marking points

      • Distance of Q at 30 s = 360 m
      • Separation = 240 m
  3. 3.A student draws the free-body diagram of a book lying on a table. The diagram shows three arrows: the weight of the book, the upward push of the table, and the downward push of the book on the table.

    From the topic: Free-body diagrams

    1. (a)Identify the arrow that should not be on the diagram and explain why.

      2 marks
      Show the answer

      Answer: The downward push of the book on the table. That force acts on the table, not on the book, and a free-body diagram shows only the forces acting on the chosen body.

      Marking points

      • The push of the book on the table
      • It acts on the table, not on the book
  4. 4.The position of the centre of gravity depends on the shape of a body and how its mass is spread.

    From the topic: Centre of mass and centre of gravity

    1. (a)State the position of the centre of gravity of (i) a uniform triangular sheet and (ii) a uniform solid cylinder.

      2 marks
      Show the answer

      Answer: (i) The point where the three medians meet. (ii) The midpoint of its axis.

      Marking points

      • Triangle: point where the medians meet
      • Cylinder: middle of its axis
    2. (b)Where is the centre of gravity of a uniform steel bangle? Explain why the bangle cannot be balanced on a fingertip placed at that point.

      2 marks
      Show the answer

      Answer: At the centre of the bangle. That point is in the empty space inside the bangle, so there is no material there to rest on a fingertip.

      Marking points

      • At the centre of the bangle
      • It lies outside the material (in empty space), so it cannot be supported there
  5. 5.A shopkeeper drags a sack of rice 6.0 m across a level floor by pulling on a rope with a force of 200 N.

    From the topic: Work

    1. (a)Calculate the work done by the pull when the rope is parallel to the floor.

      2 marks
      Show the answer

      Answer: W = FS = 200 N × 6.0 m = 1200 J.

      Marking points

      • W = FS = 200 × 6.0
      • 1200 J
    2. (b)The rope is now held at 60° to the floor, with the same 200 N pull over the same 6.0 m. Calculate the work done.

      2 marks
      Show the answer

      Answer: W = FS cos θ = 200 × 6.0 × cos 60° = 200 × 6.0 × 0.5 = 600 J.

      Marking points

      • W = FS cos θ = 200 × 6.0 × cos 60°
      • 600 J
    3. (c)Explain why less work is done in the second case, even though the pull is the same.

      2 marks
      Show the answer

      Answer: Only the component of the pull along the floor, F cos θ = 100 N, does work. The component at right angles to the floor, F sin θ, is perpendicular to the motion and does no work.

      Marking points

      • Only the component F cos θ along the motion does work
      • The perpendicular component F sin θ does no work
  6. 6.On a day of standard pressure, the mercury (ρ = 13 600 kg m⁻³) in a barometer stands 760 mm high. A second barometer is filled with an oil of density 850 kg m⁻³.

    From the topic: Barometers and manometers

    1. (a)Calculate the height of the oil column on the same day.

      3 marks
      Show the answer

      Answer: Both columns balance the same pressure, so ρ(oil) × g × h(oil) = ρ(Hg) × g × h(Hg). h(oil) = 13 600 × 0.760 ÷ 850 = 12.2 m.

      Marking points

      • ρ(oil) g h(oil) = ρ(Hg) g h(Hg), so g cancels
      • h(oil) = 13 600 × 0.760 ÷ 850
      • 12.2 m
    2. (b)Explain why mercury, rather than water or oil, is used in a simple barometer.

      2 marks
      Show the answer

      Answer: Mercury is very dense, so a short column of about 0.76 m balances the air pressure. A water or oil barometer would have to stand over 10 m high, far too tall for a laboratory.

      Marking points

      • Mercury has a very high density, so the column is short (about 0.76 m)
      • Water or oil would need an impractically tall tube (over 10 m)
    3. (c)The mercury barometer tube is tilted away from the vertical. What happens to the vertical height of the mercury column?

      1 mark
      Show the answer

      Answer: It stays the same, about 760 mm; the mercury simply fills a longer length of the tube.

      Marking points

      • Vertical height unchanged (mercury fills more of the tube's length)
    4. (d)Some air gets trapped above the mercury. How does this affect the reading? Explain.

      2 marks
      Show the answer

      Answer: The column becomes shorter. The trapped air presses down on the top of the mercury, so a shorter column is enough to balance atmospheric pressure, and the barometer reads too low.

      Marking points

      • The column becomes shorter (the reading is too low)
      • Trapped air exerts pressure on top of the column
  7. 7.Temperature, heat and internal energy are three different quantities.

    From the topic: Temperature, heat and internal energy

    1. (a)Give two definitions of temperature: one in terms of hotness, and one in terms of the flow of thermal energy.

      2 marks
      Show the answer

      Answer: Temperature is the degree of hotness or coldness of a body. It is also the physical quantity that decides the direction in which thermal energy flows between bodies.

      Marking points

      • Degree of hotness or coldness of a body
      • The quantity that decides which way thermal energy flows
    2. (b)Define heat and write its SI unit.

      2 marks
      Show the answer

      Answer: Heat is the energy transferred from one body to another because of a difference in temperature. Its SI unit is the joule (J).

      Marking points

      • Energy transferred between bodies because of a temperature difference
      • Joule (J)
    3. (c)What is meant by the internal energy of a body?

      2 marks
      Show the answer

      Answer: It is the kinetic energy plus the potential energy of all the molecules of the body.

      Marking points

      • Kinetic energy plus potential energy
      • Of all the molecules of the body
    4. (d)Write the SI unit of temperature.

      1 mark
      Show the answer

      Answer: The kelvin (K).

      Marking points

      • Kelvin (K)