Cambridge International · Cambridge IGCSE
Cambridge IGCSE Physics June 2024 Paper 5 (0625/51)
Set by Cambridge International for Cambridge IGCSE Physics, June 2024: 1 hour 15 minutes and 40 marks, on Forces, Light and the electromagnetic spectrum, Electrical quantities, Electric circuits and electrical safety. The paper itself is on Cambridge International’s website; this page adds what it covers, how to use it and original practice questions on the same topics.
Paper facts
- Series
- June 2024
- Paper
- Paper 5
- Code
- 0625/51
- Tier
- Not tiered
- Time
- 1 hour 15 minutes
- Marks
- 40
- Calculator
- Allowed
- Syllabus
- 0625 (2023–2025 syllabus)
- Links checked
- 17 November 2026
Official files
- Question paper(opens Cambridge International’s website)
- Mark scheme(opens Cambridge International’s website)
- Examiner report(opens Cambridge International’s website)
These files belong to Cambridge International. Labverse links to them and never hosts or copies them. Labverse is not affiliated with Cambridge International.
What this paper covers
4 topic groups from our map of Cambridge IGCSE Physics (0625). Revise each one with its topic pages and simulations before you sit the paper.
- Forces
Springs and load–extension graphs · Resultant force · Force, mass and acceleration · Friction and drag · Circular motion · Moments and equilibrium · Centre of gravity and stability · Momentum and impulse · Pressure
Hooke's law and springsFree-body diagrams and resultant forceCircular motionForce, mass and acceleration (F = ma)
- Light and the electromagnetic spectrum
Reflection of light · Refraction of light · Critical angle and total internal reflection · Thin lenses · Dispersion of light · Electromagnetic spectrum · Communication and digital signals
Reflection in a plane mirrorRefraction and Snell's lawLenses and ray diagramsElectromagnetic spectrum
- Electrical quantities
Electric charge · Electric fields · Electric current · E.m.f. and potential difference · Resistance · Current–voltage graphs · Electrical energy and power · Kilowatt-hours and electricity cost
Static electricity and electric fieldsCharge, current, energy and powerCircuit builderResistance of a wire
- Electric circuits and electrical safety
Circuit diagrams and components · Series and parallel circuits · Potential dividers · Electrical safety
Circuit builderSeries and parallel circuitsMains electricity and safety
How to use this paper
- 1. Time it. Set 1 hour 15 minutes for 40 marks: about 113 seconds a mark. At 38 minutes you should be roughly halfway through the marks; if you’re well behind, speed up on the short questions.
- 2. Sit it in one go. This is a hands-on lab test, so it can't be sat at home. Read the paper on Cambridge International’s website to see the kind of tasks set, then practise the skills it tests (measuring, recording, graphing and planning) with our virtual practicals.
- 3. Mark it with the official scheme. Give a mark only when your answer matches a marking point. Be strict with yourself: it’s the gaps you find that improve your grade.
- 4. Read the examiner report. It says which questions students found hardest and what the best answers did, so compare it with your own script.
- 5. Log mistakes by topic. Keep one line per topic group (Forces, Light and the electromagnetic spectrum, Electrical quantities, Electric circuits and electrical safety) and add a tally each time a mark goes there.
- 6. Revisit, then redo. Work through the weakest group’s topic pages and simulations, try the questions below, and come back to the paper in a week.
Practise the same topics
7 original exam-style questions on this paper’s topics, written in the style of Cambridge IGCSE (not taken from the paper). Try each one before you reveal the answer.
1.A cyclist squeezes the brake levers to slow down. Rubber brake blocks press against the metal rims of the moving wheels.
From the topic: Friction and drag
(a)Describe what is meant by friction.
2 marksShow the answerHide the answer
Answer: Friction is a force that acts where two surfaces touch, and it opposes (tends to stop) one surface sliding over the other.
Marking points
- force between two surfaces in contact
- opposes motion / sliding (may stop or slow it)
(b)At the bottom of a long, steep hill, the brake blocks and rims are hot. Explain why.
2 marksShow the answerHide the answer
Answer: Work is done against friction between the blocks and the rims. Going down the hill, this transfers energy from the gravitational potential (and kinetic) store of the bike and rider to the internal (thermal) store of the blocks and rims.
Marking points
- friction between blocks and rims / work done against friction
- gravitational potential / kinetic energy transferred to internal (thermal) energy of blocks and rims
(c)State one way in which friction is useful to the cyclist, apart from braking.
1 markShow the answerHide the answer
Answer: Grip between the tyres and the road lets the bike be driven forwards and turn corners without skidding (or grip of hands and feet on the handlebars and pedals).
Marking points
- any one valid use, e.g. tyre grip to move forwards / to turn without skidding, grip on handlebars or pedals
2.A pressure sensor is lowered into a tall tank of cooking oil. As the sensor moves from 0.30 m to 0.80 m below the surface, its reading rises by 4508 Pa. Use 9.8 N/kg for g.
From the topic: Pressure
(a)(Supplement) Write down the equation that links the change in pressure in a liquid with the density of the liquid, g and the change in depth.
1 markShow the answerHide the answer
Answer: Δp = ρgΔh
Marking points
- Δp = ρgΔh (or any correct rearrangement)
(b)(Supplement) Calculate the density of the oil.
3 marksShow the answerHide the answer
Answer: Δh = 0.80 − 0.30 = 0.50 m, so ρ = Δp ÷ (gΔh) = 4508 ÷ (9.8 × 0.50) = 920 kg/m³
Marking points
- Δh = 0.50 m
- 4508 ÷ (9.8 × 0.50) seen
- 920 kg/m³
(c)(Supplement) The oil is replaced by water of density 1000 kg/m³. Calculate the rise in the reading as the sensor moves through the same 0.50 m.
2 marksShow the answerHide the answer
Answer: Δp = 1000 × 9.8 × 0.50 = 4900 Pa
Marking points
- 1000 × 9.8 × 0.50 seen
- 4900 Pa
(d)(Supplement) State why the rise would be no different if the oil were in a much wider tank.
1 markShow the answerHide the answer
Answer: The pressure change depends only on the density, g and the change in depth, not on the width of the tank.
Marking points
- depends only on ρ, g and Δh (not on the width of the tank)
3.A student investigates refraction using a ray box, a semicircular or rectangular glass block, a protractor, a sharp pencil and a sheet of paper.
From the topic: Refraction of light
(a)Describe how the student can find the angle of refraction for one angle of incidence.
4 marksShow the answerHide the answer
Answer: Draw round the block and draw a normal at the point where the ray will enter. Shine the ray at that point at the chosen angle of incidence. Mark the ray leaving the block with two crosses far apart. Remove the block, join the entry and exit points to draw the ray in the glass, and measure the angle between this line and the normal with the protractor.
Marking points
- outline of block drawn and a normal drawn at the entry point
- ray directed at the entry point at a measured angle of incidence
- path of the emerging ray marked (crosses) and joined to the entry point after removing the block
- angle between the refracted ray and the normal measured with a protractor
(b)Suggest one way the student can improve the accuracy of the results.
1 markShow the answerHide the answer
Answer: Use a very narrow ray, or mark the crosses as far apart as possible, or repeat each angle and find a mean.
Marking points
- narrow ray / crosses far apart / sharp pencil / repeat and average
4.In a studio in Lagos, a microphone picks up a singer's voice and produces an analogue signal. The sound is then sent along a long cable to a radio station in another city.
From the topic: Communication and digital signals
(a)(Supplement) Describe the difference between an analogue signal and a digital signal.
2 marksShow the answerHide the answer
Answer: An analogue signal varies continuously and can have any value within a range. A digital signal has only a few set values, usually two (0 and 1, or off and on).
Marking points
- analogue: varies continuously / can take any value (in a range)
- digital: only a few set values, e.g. two (0 and 1, off and on)
(b)(Supplement) State whether the sound can be sent as an analogue signal, as a digital signal or in either form.
1 markShow the answerHide the answer
Answer: In either form.
Marking points
- either (analogue or digital)
(c)(Supplement) Along the cable the signal becomes weaker and picks up noise. Explain why a digital signal can be sent over a greater distance than an analogue signal.
3 marksShow the answerHide the answer
Answer: A digital signal can be regenerated along the route. The regenerator only has to tell whether each pulse is a 0 or a 1, so it can remove the noise and rebuild the signal accurately. When an analogue signal is amplified, the noise is amplified too, so the noise builds up.
Marking points
- digital signal is regenerated (by regenerators / repeaters) along the route
- only needs to tell 0 from 1, so noise is removed / signal restored accurately
- amplifying an analogue signal also amplifies the noise (noise builds up)
(d)(Supplement) State one other benefit of digital signalling.
1 markShow the answerHide the answer
Answer: Data can be transmitted at a higher rate.
Marking points
- more data sent per second (higher data rate)
5.A rubbed acetate rod is positively charged. It is balanced in a paper stirrup, hung on a thread, and is free to rotate. Rods X and Y are brought near one end in turn, without touching it. X repels the hanging rod. Y attracts it.
From the topic: Electric charge
(a)State the sign of the charge on X. Explain your answer.
2 marksShow the answerHide the answer
Answer: Positive, because charges of the same sign repel each other.
Marking points
- positive
- like (same-sign) charges repel
(b)A student concludes that Y must be negatively charged. Explain why this conclusion may be wrong.
2 marksShow the answerHide the answer
Answer: Y could be uncharged. A charged object attracts uncharged objects as well as oppositely charged ones, so attraction alone does not prove the sign.
Marking points
- Y could be uncharged
- uncharged objects are also attracted / only repulsion proves the sign
(c)Describe a simple experiment, other than using a hanging rod, to show that a rubbed rod is charged.
2 marksShow the answerHide the answer
Answer: Hold the rod just above some tiny pieces of paper. If the pieces jump up to the rod, it is charged.
Marking points
- hold the rod close to small pieces of paper (or a thin stream of water)
- the paper is attracted / jumps to the rod (the water bends towards it)
6.A heater is connected to a 230 V mains supply. A charge of 4000 C passes through the heater.
From the topic: E.m.f. and potential difference
(a)(Supplement) Calculate the energy transferred by the charge in the heater.
2 marksShow the answerHide the answer
Answer: W = VQ = 230 × 4000 = 920 000 J (9.2 × 10⁵ J)
Marking points
- W = VQ or 230 × 4000
- 920 000 J / 9.2 × 10⁵ J
(b)(Supplement) The current in the heater is 8.0 A. Calculate the time taken for this charge to pass.
2 marksShow the answerHide the answer
Answer: t = Q ÷ I = 4000 ÷ 8.0 = 500 s
Marking points
- t = Q/I or 4000 ÷ 8.0
- 500 s
7.An NTC thermistor is part of a fire alarm circuit. The circuit also contains a relay, a fuse and an electric bell.
From the topic: Circuit diagrams and components
(a)State what happens to the resistance of the NTC thermistor as its temperature rises.
1 markShow the answerHide the answer
Answer: It decreases.
Marking points
- resistance decreases
(b)Describe what the relay does in this circuit.
2 marksShow the answerHide the answer
Answer: A small current in the relay coil operates a switch, which turns on a separate circuit carrying a larger current to the bell.
Marking points
- a (small) current in the coil operates/closes a switch
- switching a separate circuit (with a larger current) for the bell
(c)State the purpose of the fuse.
2 marksShow the answerHide the answer
Answer: It melts and breaks the circuit if the current becomes larger than its rating, protecting the wiring and components.
Marking points
- melts / breaks the circuit
- when the current exceeds its rating