Skip to content

Cambridge IGCSE Physics (0625) · Forces

Centre of gravity and stability

1.5.3

The centre of gravity is the point through which an object's whole weight acts. For an irregular lamina it is found with a pin and a plumb line. A low centre of gravity and a wide base make an object more stable. All of topic 1.5.3 is Core.

Loading simulation…

Symbols match your course. Open the full centre of mass and stability simulation for more presets and teacher tools.

What this topic covers

An object behaves as if all of its weight acts at one point. Where that point sits decides how easily the object topples.

What the centre of gravity is (Core)

The centre of gravity is the single point through which an object's whole weight can be taken to act. On a force diagram, draw the weight as one arrow from there.

For a uniform, symmetrical object it is at the geometric centre: the middle of a metre rule, or the crossing point of a rectangle's diagonals. It need not be in the material. For a ring, or a card bent into a V, it is in the gap.

The simulation labels this point G, the centre of mass. Near the Earth the two coincide, but Cambridge answers should say centre of gravity.

Worked example: balancing a pole (Core)

A painter in Lisbon carries a 2.0 m pole, thicker at end A, on the left. Its 60 N weight acts at its centre of gravity, 0.80 m from A, where it balances on a support. A 15 N paint tin is then hung from end B. How far from A must the support now be?

Method: let the support be xx from A. The pole's weight now gives an anticlockwise moment, and the tin a clockwise one.

15×(2.0−x)=60×(x−0.80)15 \times (2.0 - x) = 60 \times (x - 0.80) 30−15x=60x−48⇒75x=78⇒x=1.04 m30 - 15x = 60x - 48 \quad\Rightarrow\quad 75x = 78 \quad\Rightarrow\quad x = 1.04\ \text{m}

Answer: 1.04 m from A, 0.24 m nearer the tin.

Finding the centre of gravity of a lamina (Core)

A plane lamina is a thin, flat object, here an irregular piece of card.

  1. Pierce three small holes close to the rim, spaced widely around it.
  2. Hang the card on a pin held in a clamp and stand, so it can swing freely. Hang a plumb line (thread and small weight) from that pin as well.
  3. Once everything has stopped moving, mark the thread's position with two well-separated crosses, then rule a line through them.
  4. Rehang the card from another hole and draw a second line. They intersect at the centre of gravity. A check line from the remaining hole should cross there too.

Why it works: when the card hangs still there is no resultant moment about the pin, so the weight's line of action runs vertically through the pin. Every line drawn this way passes through the centre of gravity.

Stability (Core)

An object is stable if it settles back after a small tilt. Picture a vertical line drawn down from its centre of gravity (the weight's line of action):

  • If this line still meets the base, the weight's moment about the tipping edge pulls the object back down.
  • If the tilt carries the line beyond the edge of the base, that moment acts the other way and the object topples.

A low centre of gravity and a wide base both increase how far an object can tilt before this happens, so both make it more stable. Racing cars are low with their wheels far apart, Bunsen burners have heavy bases, and a double-decker bus is easier to tip with its passengers upstairs.

Simulation tasks

In the simulation above, the Tilt test opens with a Bookcase on a level platform, its Books (40 kg) on the Bottom shelf. The working line under the object's controls puts G 0.5 m above the base, and Base width is 0.5 m.

  1. Press Tilt in the bar under the stage. The platform rises until the bookcase goes over, and Began to tip at 26.57° matches the Critical angle card.
  2. Choose Top shelf (changing the set-up levels the platform). G rises to 1.3 m and the critical angle falls to 10.89°. Press Tilt: it topples far sooner.
  3. Drag Base width to 1 m. The critical angle grows to 21.04°.
  4. Press Tip four times (20°), then Let go: the bookcase falls back. Five presses (25°) and Let go topple it.
  5. Choose Plumb line. The Irregular card hangs still from hole A. Press Mark line, then B, wait for Hanging at rest and mark again. On the Boomerang, the lines meet in the gap.

Common mistakes

  • Assuming the centre of gravity is always somewhere in the material. For a ring, an L-shaped bracket or a horseshoe it lies in the empty space.
  • Marking the plumb line while the card or the thread is still swinging. Wait until both are at rest, or the line will miss the centre of gravity.
  • Using two holes close together. The lines then cross at a shallow angle, so the crossing point is hard to pin down. Use holes far apart, and a third hole as a check.
  • Writing that the centre of gravity moves outside the base when an object topples. The centre of gravity stays where it is in the object; it is the vertical line through it, the line of action of the weight, that passes outside the base.
  • Thinking a heavier object is always more stable. Stability depends on the height of the centre of gravity and the width of the base; extra mass placed high up makes an object less stable.
  • Thinking every object topples once it leans past a fixed angle such as 45°. The tipping angle depends on the object's shape: a low, wide object can lean much further than a tall, narrow one.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A student wants to find the centre of gravity of a flat piece of card with an irregular shape. The student has a pin, a clamp and stand, a plumb line, a pencil and a ruler.

    1. (a)State what is meant by the term centre of gravity.

      1 mark
      Show the answer

      Answer: The point at which all of an object's weight may be considered to act.

      Marking points

      • point through which the (whole) weight (appears to) act(s)
    2. (b)Describe how the student uses the apparatus to find the centre of gravity of the card.

      4 marks
      Show the answer

      Answer: Make a hole near the edge and hang the card from the pin, clamped in the stand, so that it is free to swing, and hang the plumb line from that pin too. Once the card and thread have stopped moving, draw along the thread's position on the card. Do the same with the card hanging from a second hole. The lines intersect at the centre of gravity.

      Marking points

      • card hung from the pin through a hole so it swings freely, with the plumb line also hanging from that pin
      • when at rest, the position of the plumb line is marked on the card
      • repeated with the card hung from a different hole
      • lines intersect at the centre of gravity
    3. (c)Suggest one way of improving the accuracy of the result.

      1 mark
      Show the answer

      Answer: Any one, for example: use holes that are far apart; hang from a third hole as a check; wait until the card is completely still; use thin pencil lines; make sure the card swings freely on the pin.

      Marking points

      • any one valid precaution, e.g. holes far apart / third hole as a check / wait until still / thin lines / card free to swing
    4. (d)When the hanging card has stopped moving, its centre of gravity is on the plumb line. Explain why.

      2 marks
      Show the answer

      Answer: With the card still, the moments about the pin cancel, so the weight's line of action passes vertically through the pin. G is therefore straight below the pin, along the thread.

      Marking points

      • no resultant moment (about the pin) when at rest
      • so the weight acts vertically through the pin / G lies vertically below the pin
  2. 2.Two desk lamps have the same shape and the same total mass. Lamp X has a heavy metal base and a light shade. Lamp Y has a light plastic base and a heavy shade.

    1. (a)State which lamp is more stable. Explain your answer.

      3 marks
      Show the answer

      Answer: Lamp X. Its centre of gravity is lower, so it can be tilted further before the vertical through its centre of gravity leaves the base and it topples.

      Marking points

      • lamp X
      • lower centre of gravity
      • can tilt further before the vertical through the centre of gravity leaves the base
    2. (b)Lamp X is tilted slightly and released. Its weight still acts along a line that meets its base. Describe and explain what happens.

      2 marks
      Show the answer

      Answer: It falls back onto its base (returns upright), because the weight's moment about the tipping edge rotates it back.

      Marking points

      • returns to its upright position / falls back onto its base
      • weight has a moment about the edge (pivot) that turns it back
    3. (c)Racing cars are designed to be very stable. State two features of their design that help with this.

      2 marks
      Show the answer

      Answer: A low centre of gravity (low body, heavy parts mounted low down) and a wide base (wheels far apart).

      Marking points

      • low centre of gravity
      • wide base / wheels far apart
  3. 3.A non-uniform plank P–Q is 4.0 m long and has a weight of 300 N. It balances horizontally on a narrow support placed 1.6 m from end P.

    1. (a)State the distance of the plank's centre of gravity from P.

      1 mark
      Show the answer

      Answer: 1.6 m from end P, directly above the support.

      Marking points

      • 1.6 m from P / directly above the support
    2. (b)The only forces on the plank are its weight and the upward push of the support. Explain why the plank balances.

      2 marks
      Show the answer

      Answer: The plank's weight acts vertically through the support, so its perpendicular distance from the support is zero and its moment about the support is zero.

      Marking points

      • weight acts through the support / pivot
      • so the weight has no moment about the support
    3. (c)The support is moved to the middle of the plank, 2.0 m from P. A downward force F applied at end Q keeps the plank horizontal. Calculate F.

      3 marks
      Show the answer

      Answer: The centre of gravity is now 2.0 − 1.6 = 0.40 m from the support, on the P side. Moments: F × 2.0 = 300 × 0.40 = 120 N m, so F = 60 N.

      Marking points

      • distance of centre of gravity from the support = 0.40 m
      • F × 2.0 = 300 × 0.40 (clockwise moment = anticlockwise moment)
      • 60 N
  4. 4.A double-decker bus is tested on a platform that is slowly tilted sideways. The test is done first with the bus empty and then with heavy weights fixed to the upper deck. The bus does not slide.

    1. (a)State how the height of the bus's centre of gravity changes when the weights are added to the upper deck.

      1 mark
      Show the answer

      Answer: It moves higher (rises).

      Marking points

      • rises / moves higher
    2. (b)Explain why the loaded bus topples at a smaller angle of tilt than the empty bus.

      2 marks
      Show the answer

      Answer: A bus tips over once its weight acts along a line falling outside its base, beyond the lower wheels. Raising the centre of gravity means this line reaches the edge of the base at a smaller tilt.

      Marking points

      • topples once the weight's line of action lies outside the base (beyond the lower wheels)
      • higher centre of gravity, so this happens at a smaller tilt
    3. (c)Suggest one change to the design of a bus that would let it tilt further before toppling.

      1 mark
      Show the answer

      Answer: Any one, for example: place the heaviest parts (engine, fuel tank, batteries) as low as possible, or make the wheels further apart.

      Marking points

      • heavy parts placed lower / wider wheelbase (wheels further apart)

Quick check

6 questions

  1. 1.What is the centre of gravity of an object?
  2. 2.In the plumb-line experiment, why is the card hung from a second hole?
  3. 3.Which change makes a tall vase harder to knock over?
  4. 4.A box is tilted onto one edge and released. It falls back onto its base. What must have been true when it was released?
  5. 5.Where is the centre of gravity of a uniform metal ring?
  6. 6.A uniform metre rule is placed on a narrow support at its 40 cm mark and released. What happens?