An original Labverse practice paper — not an official exam paper
Cambridge IGCSE Physics (0625)
Cambridge IGCSE Physics Paper 3 practice paper C
Written by Labverse from our own exam-style questions, to the same time and total marks as Cambridge International’s Paper 3 (0625/31, 0625/32, 0625/33), on the same topics. It is not set, checked or endorsed by Cambridge International.
- Time allowed
- 1 hour 15 minutes
- Total marks
- 80
- Questions
- 17
- Level
- Core
Instructions
- Answer every question. Work in one sitting and stop when the time is up.
- The marks for each part are shown beside it. Use them to judge how much to write.
- Show your working for calculations and give the unit with every answer.
To print the answers too, open the mark scheme at the end first.
Marks by topic
- Motion · 3 marks
- Forces · 12 marks
- Energy, work and power · 10 marks
- Thermal physics · 6 marks
- Transfer of thermal energy · 6 marks
- Waves and sound · 13 marks
- Light and the electromagnetic spectrum · 6 marks
- Electrical quantities · 9 marks
- Electric circuits and electrical safety · 1 mark
- Magnetism and electromagnetic effects · 9 marks
- Nuclear physics · 5 marks
Questions
- Question 1 (3 marks)Speed and velocity
Two cars pass each other on a straight road. Car A moves east at 20 m/s and car B moves west at 20 m/s.
(a)State one quantity that is the same for both cars and one quantity that is different.
[2](b)Define velocity.
[1]
- Question 2 (8 marks)Centre of gravity and stability
A student wants to find the centre of gravity of a flat piece of card with an irregular shape. The student has a pin, a clamp and stand, a plumb line, a pencil and a ruler.
(a)State what is meant by the term centre of gravity.
[1](b)Describe how the student uses the apparatus to find the centre of gravity of the card.
[4](c)Suggest one way of improving the accuracy of the result.
[1](d)When the hanging card has stopped moving, its centre of gravity is on the plumb line. Explain why.
[2]
- Question 3 (4 marks)Centre of gravity and stability
A double-decker bus is tested on a platform that is slowly tilted sideways. The test is done first with the bus empty and then with heavy weights fixed to the upper deck. The bus does not slide.
(a)State how the height of the bus's centre of gravity changes when the weights are added to the upper deck.
[1](b)Explain why the loaded bus topples at a smaller angle of tilt than the empty bus.
[2](c)Suggest one change to the design of a bus that would let it tilt further before toppling.
[1]
- Question 4 (5 marks)Work done
An electric motor winds in a cable that raises a lift car at a steady speed through a vertical height of 12 m. The cable does 66 kJ of work on the lift car. During the lift, the electrical supply does 150 kJ of electrical work on the motor.
(a)Calculate the upward force that the cable exerts on the lift car.
[2](b)State how much energy the electric current transfers to the motor during the lift.
[1](c)Calculate the energy that does not reach the lift car, and suggest where it goes.
[2]
- Question 5 (5 marks)Power
An electric pump on a farm lifts water into a storage tank. In 10 minutes the pump transfers 1.8 MJ of energy.
(a)Define power.
[1](b)Calculate the power of the pump.
[3](c)State how much energy the pump transfers each second.
[1]
- Question 6 (6 marks)Absolute zero and the kelvin scale
A science textbook lists some temperatures on different scales.
(a)State the equation that links a temperature T in kelvin with the same temperature θ in degrees Celsius.
[1](b)Mercury freezes at −39 °C. Convert this temperature to kelvin.
[2](c)Helium becomes a liquid at 4 K. Convert this temperature to degrees Celsius.
[2](d)Water in a kettle is heated from 18 °C to 100 °C. State the rise in temperature in kelvin.
[1]
- Question 7 (6 marks)Thermal radiation
Two identical metal water tanks stand in strong sunshine on a roof in Lusaka. Tank P is painted dull black. Tank Q has a shiny silver surface.
(a)State which tank's water warms up faster. Give a reason.
[2](b)State what happens to most of the radiation that reaches tank Q.
[1](c)At night, both tanks hold water at the same temperature. State and explain which tank loses energy faster by radiation.
[2](d)Suggest why many houses in hot, sunny countries are painted white.
[1]
- Question 8 (5 marks)Transverse and longitudinal waves
A slinky spring lies stretched along a laboratory bench. A student makes two different waves on it: first by moving one end from side to side across the bench, then by pushing and pulling the end along the length of the slinky.
(a)Name the type of wave made by moving the end from side to side.
[1](b)For the wave made by pushing and pulling the end, describe how the coils move, and name this type of wave.
[2](c)A small paper marker is stuck to one coil. Describe the motion of the marker as either wave passes, and state what this shows about waves.
[2]
- Question 9 (7 marks)Reflection, refraction and diffraction
Plane water waves in a ripple tank pass through a narrow gap between two barriers. Later, one barrier is taken away, so the waves pass the end of a single barrier.
(a)Name the effect that makes the waves spread out after the gap.
[1](b)Describe what happens to the waves after they pass through the gap.
[2](c)State what happens to the wavelength of the waves as they pass through the gap.
[1](d)Describe what happens to the waves that pass the end of the single barrier.
[1](e)State one other effect a ripple tank can show, and what is put in the tank to show it.
[2]
- Question 10 (1 mark)Ultrasound
A doctor examines a patient's gall bladder with ultrasound. A probe on the skin sends short pulses into the body and receives the echoes.
(a)State what is meant by ultrasound.
[1]
- Question 11 (6 marks)Communication and digital signals
A geologist working in a remote part of the Andes carries a satellite phone. The camp has a television that receives its programmes from a satellite through a dish, and a radio that picks up a local station.
(a)State which region of the electromagnetic spectrum is mainly used to send signals to and from artificial satellites.
[1](b)Name the two types of artificial satellite used by satellite phones.
[2](c)State which of these two types is used for direct broadcast satellite television.
[1](d)The television is switched between channels with a remote control. Name the region of the electromagnetic spectrum that the remote control uses.
[1](e)Name the region of the electromagnetic spectrum that carries the local radio station's broadcasts.
[1]
- Question 12 (5 marks)Electric current
A student builds a circuit containing a cell, a switch, a lamp and an ammeter.
(a)State how the ammeter must be connected in the circuit.
[1](b)The ammeter has two ranges, 0–1 A and 0–10 A. The current is about 0.3 A. State which range the student should use and explain why.
[2](c)Describe how charge flows through the metal wires of the circuit.
[2]
- Question 13 (4 marks)Resistance
A headlamp bulb in a car has a resistance of 3.0 Ω when it is lit. It is connected to a 12 V battery.
(a)Calculate the current in the bulb.
[3](b)A different bulb with a larger resistance is connected to the same battery. State the effect on the current.
[1]
- Question 14 (1 mark)Series and parallel circuits
A resistor is connected across a battery. A second resistor is then connected in parallel with the first one.
(a)State the effect on the combined resistance of connecting a second resistor in parallel with a first resistor.
[1]
- Question 15 (6 marks)Magnetic fields
A student in Cairo uses a small plotting compass to map the magnetic field around a bar magnet. The magnet lies on a large sheet of paper.
(a)Describe how the student uses the compass to plot one field line.
[4](b)State how the student shows the direction of the field on the line.
[1](c)Suggest why the student keeps a steel pencil case well away from the paper during the experiment.
[1]
- Question 16 (3 marks)Magnetic fields
A student draws the magnetic field around a single bar magnet. The drawing has these faults: the arrows point from the S pole to the N pole, two lines cross near the S pole, and the lines are spaced evenly all round the magnet.
(a)State the correct direction of the arrows on the lines outside the magnet.
[1](b)Explain why two field lines must not cross.
[2]
- Question 17 (5 marks)Radiation safety precautions
A school keeps a small sealed beta source for class experiments.
(a)Describe how the source should be stored when it is not in use.
[2](b)Describe two precautions the teacher takes while using the source.
[2](c)State one precaution taken when the source is carried from the store to the laboratory.
[1]
End of practice paper · 80 marks in total
Mark schemeOpen it only after you have finished the paper.ShowHide
Question 1 (3 marks)
(a)Their speed is the same; their velocity is different because the directions are opposite. [2]
- speed is the same
- velocity is different (opposite directions)
(b)Speed in a given direction. [1]
- speed in a stated/given direction
Revise: Speed and velocity · Motion graphs simulation
Question 2 (8 marks)
(a)The point at which all of an object's weight may be considered to act. [1]
- point through which the (whole) weight (appears to) act(s)
(b)Make a hole near the edge and hang the card from the pin, clamped in the stand, so that it is free to swing, and hang the plumb line from that pin too. Once the card and thread have stopped moving, draw along the thread's position on the card. Do the same with the card hanging from a second hole. The lines intersect at the centre of gravity. [4]
- card hung from the pin through a hole so it swings freely, with the plumb line also hanging from that pin
- when at rest, the position of the plumb line is marked on the card
- repeated with the card hung from a different hole
- lines intersect at the centre of gravity
(c)Any one, for example: use holes that are far apart; hang from a third hole as a check; wait until the card is completely still; use thin pencil lines; make sure the card swings freely on the pin. [1]
- any one valid precaution, e.g. holes far apart / third hole as a check / wait until still / thin lines / card free to swing
(d)With the card still, the moments about the pin cancel, so the weight's line of action passes vertically through the pin. G is therefore straight below the pin, along the thread. [2]
- no resultant moment (about the pin) when at rest
- so the weight acts vertically through the pin / G lies vertically below the pin
Revise: Centre of gravity and stability · Centre of mass and stability simulation
Question 3 (4 marks)
(a)It moves higher (rises). [1]
- rises / moves higher
(b)A bus tips over once its weight acts along a line falling outside its base, beyond the lower wheels. Raising the centre of gravity means this line reaches the edge of the base at a smaller tilt. [2]
- topples once the weight's line of action lies outside the base (beyond the lower wheels)
- higher centre of gravity, so this happens at a smaller tilt
(c)Any one, for example: place the heaviest parts (engine, fuel tank, batteries) as low as possible, or make the wheels further apart. [1]
- heavy parts placed lower / wider wheelbase (wheels further apart)
Revise: Centre of gravity and stability · Centre of mass and stability simulation
Question 4 (5 marks)
(a)F = W ÷ d = 66 000 ÷ 12 = 5500 N [2]
- 66 000 ÷ 12 seen (kJ converted to J)
- 5500 N
(b)150 kJ, because the electrical work done equals the energy transferred. [1]
- 150 kJ
(c)150 − 66 = 84 kJ. It heats the motor, the cables and the surroundings (their internal (thermal) stores), and a little leaves as sound. [2]
- 84 kJ
- heating of motor / cables / surroundings (internal (thermal) store) or sound
Revise: Work done · Work done simulation
Question 5 (5 marks)
(a)The work done per unit time, or the energy transferred per unit time. [1]
- work done per unit time / energy transferred per unit time
(b)1.8 MJ = 1 800 000 J and 10 min = 600 s. P = ΔE ÷ t = 1 800 000 ÷ 600 = 3000 W (3.0 kW). [3]
- 1 800 000 J and 600 s used
- P = ΔE ÷ t / 1 800 000 ÷ 600 seen
- 3000 W (3.0 kW)
(c)3000 J [1]
- 3000 J
Revise: Power · Power and efficiency simulation
Question 6 (6 marks)
(a)T (in K) = θ (in °C) + 273 [1]
- T = θ + 273 (or θ = T − 273)
(b)T = −39 + 273 = 234 K [2]
- −39 + 273 seen
- 234 K
(c)θ = 4 − 273 = −269 °C [2]
- 4 − 273 seen
- −269 °C
(d)100 − 18 = 82 K [1]
- 82 K
Revise: Absolute zero and the kelvin scale · Gas laws and particles simulation
Question 7 (6 marks)
(a)Tank P, because a dull black surface is a better absorber of radiation than a shiny silver one. [2]
- tank P
- dull black is a better absorber (shiny silver is a poor absorber)
(b)It is reflected. [1]
- reflected
(c)Tank P, because a dull black surface is a better emitter of infrared than a shiny silver surface. [2]
- tank P
- dull black is a better emitter (shiny silver is a poor emitter)
(d)White surfaces reflect most of the sunlight, so the walls absorb less energy and the house stays cooler. [1]
- white reflects (most) sunlight / absorbs less, so the house stays cooler
Revise: Thermal radiation · Conduction, convection and radiation simulation
Question 8 (5 marks)
(a)Transverse [1]
- transverse
(b)The coils vibrate backwards and forwards, parallel to the direction in which the wave travels. It is a longitudinal wave. [2]
- coils vibrate parallel to (along) the direction of travel
- longitudinal
(c)The marker vibrates about one position and ends up where it started. This shows that the wave transfers energy without transferring the slinky (matter). [2]
- marker vibrates about a fixed position / returns to where it started
- waves transfer energy without transferring matter
Revise: Transverse and longitudinal waves · Transverse and longitudinal waves simulation
Question 9 (7 marks)
(a)Diffraction [1]
- diffraction
(b)They spread out into the region behind the barriers, and their wavefronts become curved. [2]
- spread out (into the region behind the barrier)
- wavefronts become curved
(c)It does not change. [1]
- stays the same
(d)They bend round the end into the region behind the barrier. [1]
- bend (diffract) round the edge into the region behind the barrier
(e)Refraction, using a glass plate to make a shallower region (or reflection, using a straight barrier). [2]
- refraction (or reflection)
- glass plate making the water shallower (or a straight barrier for reflection)
Revise: Reflection, refraction and diffraction · Ripple tank simulation
Question 10 (1 mark)
(a)Sound pitched above 20 kHz (20 000 Hz), beyond the range of human hearing. [1]
- sound too high-pitched to hear: over 20 kHz (20 000 Hz)
Question 11 (6 marks)
(a)Microwaves. [1]
- microwaves
(b)Low-orbit satellites and geostationary satellites. [2]
- low-orbit (low Earth orbit) satellites
- geostationary satellites
(c)Geostationary satellites. [1]
- geostationary
(d)Infrared. [1]
- infrared
(e)Radio waves. [1]
- radio waves
Revise: Communication and digital signals · Electromagnetic spectrum simulation
Question 12 (5 marks)
(a)In series with the lamp. [1]
- in series
(b)0–1 A, because the reading still fits on this scale and it gives a larger deflection, so it can be read more precisely. [2]
- 0–1 A range
- reading stays on scale and can be read more precisely (larger deflection / smaller divisions)
(c)Free electrons in the metal move (drift) through the wire, carrying the charge round the circuit. [2]
- free electrons carry the charge
- they move/drift through the wire, round the circuit
Revise: Electric current · Circuit builder simulation
Question 13 (4 marks)
(a)I = V ÷ R = 12 ÷ 3.0 = 4.0 A [3]
- I = V/R
- 12 ÷ 3.0
- 4.0 A
(b)The current is smaller. [1]
- current decreases / is smaller
Revise: Resistance · Circuit builder simulation
Question 14 (1 mark)
(a)The combined resistance decreases; it is less than that of either resistor. [1]
- combined resistance decreases / less than either resistor
Revise: Series and parallel circuits · Circuit builder simulation
Question 15 (6 marks)
(a)Put the compass near the N pole and mark a dot at the point of the needle's N end. Then reposition the compass so that the dot lies under the needle's S end, and mark where the N end now points. Repeat until the S pole is reached, then join the dots with a smooth curve. [4]
- put the compass on the paper near one pole (the N pole)
- mark a dot at the N end (the point) of the needle
- slide the compass until the S end (tail) of the needle sits on that dot, then mark again
- repeat until the other pole is reached and join the dots with a smooth line
(b)Draw arrows on the line pointing the way the N end of the needle pointed, from the N pole towards the S pole. [1]
- arrows pointing from N to S / the way the N end of the needle points
(c)Steel is magnetic, so it could be magnetised and its field could turn the compass needle, making the plot wrong. [1]
- steel is magnetic / its field affects (deflects) the compass needle
Revise: Magnetic fields · Magnetic field of a bar magnet simulation
Question 16 (3 marks)
(a)Pointing from N towards S: each line leaves the N pole and ends at the S pole. [1]
- from N (north pole) to S (south pole)
(b)A field can point only one way at each place. Where two lines crossed, there would be two directions at one spot, which cannot happen. [2]
- a field has just one direction at each place (the force on an N pole acts one way)
- crossing lines would give two directions at one point / a compass cannot point two ways
Revise: Magnetic fields · Magnetic field of a bar magnet simulation
Question 17 (5 marks)
(a)In a lead-lined box, kept in a locked cupboard that carries the radiation warning sign. [2]
- in a lead-lined box (container)
- in a locked cupboard / labelled with a warning sign
(b)Any two of: lifts it with tongs, never the fingers; holds it at arm's length; points it away from people; uses it for as short a time as possible. [2]
- first precaution, e.g. handles it with tongs
- second precaution, e.g. holds it at arm's length / points it away from people / short time
(c)It stays inside its shielded (lead-lined) box while it is carried. [1]
- carried in its shielded (lead-lined) box
Revise: Radiation safety precautions · Alpha, beta and gamma radiation simulation