What this topic covers
In a Nairobi taxi, a small current through a relay connects the starter motor. Syllabus 4.5.3 explains how.
Round a straight wire (Core)
The lines are rings with the wire at their centre, in a plane perpendicular to the wire. Their direction follows the current's: aim your right thumb with the conventional current and your bent fingers give it (the right-hand grip rule). So ⊙ (current towards you) means anticlockwise, and ⊗ clockwise.
Inside and round a solenoid (Core)
Outside the coil the lines copy a bar magnet's pattern, leaving the N end and curving back to the S end. Inside, straight parallel lines carry them from S to N, so every line forms a loop. Quick test: look at one end; anticlockwise current means that end is N.
Finding the pattern (Core)
- Push the wire vertically through a horizontal card. For a solenoid, thread the coil through holes so the card lies along its axis.
- With a large current on, sprinkle iron filings and tap the card: they gather along the lines.
- Add plotting compasses: each needle's N end gives an arrow.
- Reverse the current: the needles swing round, but the filings stay put.
Strength and current (Supplement)
A straight wire's field is strongest close in and fades with distance, so the circles spread apart. A solenoid's is strong and almost uniform inside, where the lines are close, parallel and evenly spaced, and much weaker outside. More current strengthens the field everywhere (lines drawn closer); less weakens it. Reversing the current flips every arrow and swaps a solenoid's poles, but the pattern's shape never changes.
Relays (Core)
A relay is an electromagnet used as a switch: a small current in its coil, which has a soft iron core, controls a separate, large-current circuit in car starters or automatic street lamps.
Worked explanation: why soft iron?
- Current in the coil sets up a magnetic field, which magnetises the soft iron and makes the electromagnet far stronger.
- The electromagnet pulls the iron armature, which rocks on its pivot and closes the contacts: the large current flows.
- Stop the coil current and soft iron loses its magnetism at once; a spring then returns the armature and the contacts part.
Steel, by contrast, would remain a magnet and go on attracting the armature, so the contacts would stay shut.
Loudspeakers (Core)
A coil fixed to a light cone sits in a permanent magnet's field. An amplifier sends an alternating current through the coil, so the coil's field keeps changing size and direction. The two fields interact, so a changing force acts on the coil and drives the cone in and out in step with the current, making sound waves. Phones, headphones and radios all have one.
Simulation tasks
In the simulation above, the Straight wire set-up starts with a 5 A current coming up out of the card (⊙).
- (Core) Field lines go says Anticlockwise. Tap Reverse: all eight needles swing round and it says Clockwise. Tap Filings, then Reverse: the filings do not change. Tap Filings to clear them.
- (Supplement) Field at compass 1, 4 cm out, gives 25 μT. Drag Distance from the wire down to 2 cm: it doubles to 50 μT. Tap Less I three times (2 A): 20 μT, and just three circles.
- (Core) Pick Solenoid: N pole says Right-hand end, and the compass beyond it points away from the coil. Reverse gives Left-hand end. (Supplement) Set Current to 4 A: Field inside doubles from 4.05 mT to 8.09 mT. Return it to 2 A.
- (Core) Pick Relay and tap Switch: 0.05 A in the coil circuit pulls the armature, Contacts says Closed, and the motor circuit takes 6 A.
- (Core, 4.1) Pick Electromagnet, then Soft iron: 6 clips, which drop when you tap Switch. Tap it again, pick Steel, and set Current to 5 A and Turns to 400: 19 clips. Tap Switch: 5 stay, as steel makes a permanent magnet.
Values in teslas, Earth and Demagnetise go beyond 0625.