Lining up the domains
Section 8.8 pictures a ferromagnetic material as tiny regions called magnetic domains, each a small magnet. In an unmagnetised steel bar they point in random directions and cancel out. Magnetisation turns most of them to face one way; demagnetisation scatters them again. Steel resists: only a strong field turns its domains. Once turned, though, they keep their new direction, so magnetised steel stays a magnet.
Method 1: stroking
Lay the steel bar flat on a horizontal surface.
- Single-touch method: run one pole of a permanent magnet (the N pole, for example) along the whole bar, end to end. Lift it well clear and carry it back to the start, so every stroke goes the same way. Repeat several times.
- Double-touch method: place the N pole of one permanent magnet beside the S pole of another at the middle of the bar. Slide both outwards together, towards opposite ends. Your book rates this as more efficient.
Each end of the bar takes the pole opposite to the one that stroked towards it: stroke towards end B with an N pole, and B becomes S.
Method 2: inside a solenoid
Put the steel bar inside a long coil of insulated copper wire with a few hundred turns, and pass a direct current through it. The steady field lines up the domains, and the bar stays magnetised after the current is switched off.
To predict the poles, use the right-hand grip rule: wrap your right hand round the solenoid with your fingers following the current through the turns, from the battery's + terminal towards its − terminal. Your thumb, along the bar, shows its N end.
Worked example: making end P the N pole
A steel bar PQ lies inside a solenoid, P on the left. Which way must the current go round the turns for P to become N?
- The thumb must point at P, so point your right thumb left.
- Your fingers curl round the coil. Looking at end P from the left, they turn anticlockwise.
- So the current must circle anticlockwise as seen from P. Connect the battery that way round, switch on briefly, then off.
- Test with a compass: P should repel the needle's N end. Only a magnet repels, so P is N.
Reversing the battery would make P an S pole.
Demagnetising a magnet
Knock the domains out of line and a magnet is demagnetised. The book gives three ways:
- Heating: heat it strongly. Its atoms vibrate harder, the neat order of the domains breaks down, and the magnetism vanishes quickly.
- Hammering: strike it hard, again and again. The jolts knock the domains out of alignment.
- Alternating current: pass a.c. through a long solenoid, hold the magnet inside, then draw it out slowly until it is well away. The reversing field flips the domains to and fro, more weakly as the magnet moves out, until they are left pointing at random.
D.c. would not work: it would just magnetise the bar again, one way.
Magnetising steel on screen
In the simulation above, skip Straight wire, which is beyond Class 9, and choose Solenoid. Its switch is already on, so a direct current flows from the cell.
- Pick Steel under Core. N pole reads Right-hand end: seen from the right, the current runs anticlockwise round the turns, and your right thumb points right.
- Press Switch to stop the current. The card still reads Right-hand end: the steel is now a permanent magnet.
- Press Demagnetise. An a.c. flows and fades to nothing, flipping the steel's magnetism to and fro more weakly each time; then the card reads None. Your book instead draws the magnet slowly out of an a.c. coil; both ways, the field it feels reverses and fades.
- Pick Soft iron and press Switch to turn the current on: Right-hand end. Press Switch again: straight back to None, as soft iron is only a temporary magnet.
- Choose Electromagnet and pick Steel. Set Turns to 400 and Current to 5 A, then press Switch to turn the current on: 19 clips. Press Switch again: 5 stay on the steel. Demagnetise drops them.
Field values in teslas are extras beyond Class 9.