Permanent magnets work in motors, generators, loudspeakers, door catchers and iron separators. An electromagnet is a temporary magnet: soft iron inside a coil, magnetic only while a current flows, and stronger with more cells or turns. Relays, circuit breakers, receivers and cranes use it.
A permanent magnet stays magnetic with no electricity at all, so it suits jobs that need a steady field. Your book's list includes:
generators (a.c. and d.c.) and d.c. motors
the moving coil loudspeaker
door catchers, and the magnetic strips that keep refrigerator and freezer doors tightly shut
separating iron from mixtures: a flour mill pulls stray iron nails out of grain before it is ground
lifting iron splinters out of an injured eye
resetting the iron pointer of a maximum and minimum thermometer
Two are described further:
A.C. generator: a coil spins in the gap between a permanent magnet's N and S poles. The field through the coil keeps changing, so an e.m.f. is induced and an alternating current flows in a circuit joined to its ends. A motor does the reverse: current in a coil between the poles makes it spin.
Moving coil loudspeaker: a light voice coil, fixed to the cone, sits in the gap of the magnet. A varying current flows in the coil, and the magnet's field pushes and pulls on it. Coil and cone vibrate, giving out sound.
Electromagnets (8.7)
An electromagnet is a soft iron core, such as a nail or a rod, that behaves as a magnet only while a current flows in a coil of wire wound round it. It is a temporary magnet.
In Activity 5, insulated copper wire is coiled round an iron nail and joined, through a switch, to a two-cell battery. Paper clips are held near the nail's tip:
Switch
Clips
Reason
OFF
not attracted
no current, so no magnetic field
ON
cling to the nail
the coil's field magnetises the iron
OFF again
drop off
soft iron loses its magnetism at once
More cells in the battery, or more turns on the coil, make the field stronger, and the nail holds more clips.
Uses of electromagnets
The book finds electromagnets in cranes, relays, circuit breakers, electric bells, reed switches, tape recorders, telephone receivers and even maglev trains. Know how these three work:
Magnetic relay: a switch worked by an electromagnet. Closing the switch in the low-current input circuit, which is safe to handle, sends a small current through the coil. The electromagnet attracts one end of an iron armature, which rocks on its pivot; the far end presses two springy contacts together, and the separate high-current circuit is switched ON.
Telephone receiver: varying current from the microphone in the other handset flows through an electromagnet under an iron diaphragm. The pull changes with the current, so the diaphragm vibrates back and forth and makes sound.
Electromagnetic crane: the crane's very strong electromagnet picks up heavy iron and steel scrap, even a whole car. Once the load is over the right spot, the operator switches the current OFF and the load drops.
Worked explanation: the circuit breaker
A circuit breaker lets a current up to a fixed maximum pass safely, but cuts off anything larger.
The electromagnet's coil, the iron armature and a copper strip all carry the circuit's current.
At a normal current, the electromagnet's pull is too weak to move the armature, so the circuit stays closed.
A fault makes the current too large. The electromagnet becomes strong enough to pull the armature away from the copper strip.
The contacts separate, the circuit breaks and the current stops, so appliances do not overheat and burn.
An electromagnet suits this job because its strength rises with the current.
Electromagnets on screen
In the simulation above, the Straight wire view it opens on goes beyond Class 9, so turn to the other set-ups.
Choose Electromagnet. With None (air) under Core, Clips held stays at 0. Pick Soft iron, like the nail in Activity 5: 6 clips at 200 turns and 2 A.
Press Switch to turn the current OFF: every clip falls, because soft iron makes a temporary magnet. Press Switch again to turn it back ON.
Press Record. Set Turns to 400 and press Record (11 clips). Raise Current to 5 A, as extra cells would, and press Record (28 clips). The Results table shows each change.
Choose Relay and press Switch. The Coil circuit card shows a small current, the armature is pulled down, Contacts reads Closed and the Motor circuit card shows a large current. Press Switch again: the spring opens the contacts.
The readings in amperes are extras: your book only compares a low current with a high one.
Common mistakes
✕Calling an electromagnet a permanent magnet. It is a temporary magnet: switch off its current and the magnetism goes.
✕Saying an electromagnet should have a steel core. Steel would keep its magnetism after the current stops, so a crane could not drop its load; soft iron is used.
✕Saying the nail in Activity 5 holds more clips just because the wire is longer. Extra wire helps only when it is wound on as extra turns: more turns on the coil, or more cells in the battery, are what make the field stronger.
✕Mixing up the two circuits of a relay. The low-current input circuit only works the electromagnet; the high-current circuit is switched ON by the contacts and is not joined to the input circuit.
✕Writing that a circuit breaker cuts off every current. It passes currents up to a set maximum; only a current that is too large makes the electromagnet pull the armature away.
✕Thinking the diaphragm of a telephone receiver can be plastic. It is iron, so that the electromagnet can pull on it.
Exam-style questions
Original questions written in the style of Punjab board exams. Try each one before you reveal the answer.
1.Answer these short questions about magnets and electromagnets.
(a)What is an electromagnet? Why is it called a temporary magnet?
2 marks
Show the answerHide the answer
Answer: An electromagnet is a soft iron core (such as a nail) that becomes a magnet when a current flows in a coil of wire wound round it. It is called temporary because its magnetism disappears once the current is switched OFF.
Marking points
Soft iron core that becomes a magnet when a current flows in a coil round it
Its magnetism disappears once the current is switched OFF
(b)Name four uses of permanent magnets.
2 marks
Show the answerHide the answer
Answer: Any four of: generators (a.c. or d.c.); d.c. motors; moving coil loudspeakers; door catchers; magnetic strips on refrigerator doors; separating iron from mixtures, e.g. in flour mills; removing iron splinters from the eye; resetting the pointer of a maximum and minimum thermometer.
Marking points
Any two correct uses
Two more correct uses
(c)Give two ways of making an electromagnet stronger.
2 marks
Show the answerHide the answer
Answer: Use more cells in the battery, so a larger current flows. Wind more turns of wire on the coil.
Marking points
More cells (a larger current)
More turns on the coil
(d)Why is the core of an electromagnet made of soft iron?
2 marks
Show the answerHide the answer
Answer: Soft iron is magnetised easily, giving a strong magnet while the current flows, and its magnetism disappears once the current is switched OFF, so the magnet can be turned off.
Marking points
Soft iron is easily magnetised
Its magnetism disappears when the current stops (so the magnet can be switched OFF)
2.A student repeats Activity 5 with an iron nail wound with insulated copper wire. With 50 turns and one cell, the nail holds 3 paper clips. With 50 turns and two cells, it holds 7 clips. With 100 turns and two cells, it holds 13 clips. With the switch OFF, it holds none.
(a)Which change was made between the first and second results, and what did it show?
2 marks
Show the answerHide the answer
Answer: The number of cells was increased from one to two. More cells made the electromagnet stronger, so it held more clips.
Marking points
The number of cells was increased (from one to two)
More cells made the electromagnet stronger (more clips held)
(b)How many more clips were held when the number of turns was doubled?
1 mark
Show the answerHide the answer
Answer: 13 − 7 = 6 more clips.
Marking points
6 clips
(c)What conclusion can be drawn from the second and third results?
1 mark
Show the answerHide the answer
Answer: Increasing the number of turns makes the magnetic field of the electromagnet stronger.
Marking points
More turns give a stronger electromagnet (stronger magnetic field)
(d)Explain why the nail held no clips with the switch OFF.
2 marks
Show the answerHide the answer
Answer: With the switch OFF there is no current, so the coil produces no magnetic field. Soft iron does not keep its magnetism, so the nail is not a magnet.
Marking points
No current, so no magnetic field from the coil
The iron nail is a temporary magnet and keeps no magnetism
3.A magnetic relay is used to switch on a large motor in a factory.
(a)Describe how the relay works. You may draw a labelled diagram.
4 marks
Show the answerHide the answer
Answer: Switching ON the input circuit sends a small current through the electromagnet's coil. This attracts the pivoted iron armature, which turns about its pivot so that its other end pushes the springy metal contacts together. This switches ON the high-current circuit, and the motor runs.
Marking points
A small current in the input circuit flows through the electromagnet
The pivoted iron armature is pulled towards the electromagnet
The armature turns and pushes the contacts together
The high-current circuit is switched ON (the motor runs)
(b)Give the reason why the relay's input circuit carries only a low current.
1 mark
Show the answerHide the answer
Answer: Safety: the person working the switch never handles the high-current circuit.
Marking points
For safety
(c)What happens when the input circuit is switched OFF?
1 mark
Show the answerHide the answer
Answer: The electromagnet loses its magnetism, the armature is released and the contacts separate, so the motor stops.
Marking points
The armature is released and the contacts open (the motor stops)
4.Electromagnets are used in many devices in homes and offices.
(a)Explain how a circuit breaker protects appliances when the current becomes too large.
3 marks
Show the answerHide the answer
Answer: The current passes through the electromagnet's coil and the iron armature. When the current is too large, the electromagnet becomes strong enough to pull the armature away from the copper strip. The circuit breaks and the current stops, so the appliances are protected from burning.
Marking points
The current flows through the electromagnet's coil (and the armature)
A large current makes the electromagnet pull the armature away from the copper strip
The circuit breaks and the current stops
(b)Describe how the receiver of a telephone produces sound.
3 marks
Show the answerHide the answer
Answer: A varying current from the microphone at the other end passes through the coil of an electromagnet. The pull of the electromagnet on the iron diaphragm varies with the current. The diaphragm vibrates back and forth and produces sound.
Marking points
A varying current (from the microphone) passes through the electromagnet
The force on the iron diaphragm varies
The diaphragm vibrates and produces sound
(c)Why are electromagnets, and not permanent magnets, used in scrapyard cranes?
1 mark
Show the answerHide the answer
Answer: The load can be dropped just by switching OFF the current.