Skip to content

Cambridge IGCSE Physics (0625) · Magnetism and electromagnetic effects

The a.c. generator

4.5.2Supplement

Supplement only: a coil spinning in a magnetic field, or a magnet spinning in a coil, gives an alternating e.m.f.; slip rings and brushes link a spinning coil to the circuit. The e.m.f. is zero with the coil's plane at right angles to the field and largest with it parallel.

Loading simulation…

Symbols match your course. Open the full electromagnetic induction simulation for more presets and teacher tools.

What this topic covers

Hydroelectric turbines on the Zambezi, a car's alternator in Mexico City and the hub dynamo on a Dutch bicycle all turn motion into alternating current. Section 4.5.2 explains how; induction itself is on the Electromagnetic induction page.

A coil spinning in a field (Supplement)

  • A rectangular coil of many turns spins on an axle in the gap between a magnet's poles, driven by a turbine, engine or hand crank.
  • Each end of the coil is attached to its own slip ring, a complete metal ring on the axle that turns with the coil.
  • A fixed carbon brush presses on each ring, so each end of the coil always feeds the same wire of the circuit, and nothing twists.

Each long side moves up through the field for half a turn, then down for the next, so its e.m.f. reverses every half turn. The slip rings pass this straight to the circuit: the output is alternating.

A magnet spinning beside a coil (Supplement)

Or swap the roles: spin a magnet inside a fixed coil. As the poles sweep past, the field through the coil keeps reversing, inducing an alternating e.m.f. The coil never moves, so no slip rings are needed. A bicycle hub dynamo works this way: a ring of magnets turns around a fixed coil, so it gives a.c. Its name can mislead, because in physics a "dynamo" usually means a generator with a split ring, which gives d.c.

Coil position and the e.m.f. (Supplement)

Start with the coil's plane at right angles to the field, upright when the field is horizontal.

Turned throughCoil's planee.m.f.
0At right angles to the fieldZero
¼ turnParallel to the fieldPeak
½ turnAt right angles againZero
¾ turnParallel againTrough
1 turnBack where it beganZero

At the zeros the sides glide along the field lines; at a peak or trough they cut straight across them, in opposite directions for the two. One turn gives one complete cycle.

The trap: the e.m.f. is zero just when the most field passes through the coil, because what counts is how fast the sides cut the lines.

Changing the graph (Supplement)

  • Turn faster: taller peaks and more cycles each second (a higher frequency).
  • More turns, or a stronger magnet: the peaks grow, but the cycles per second stay the same.

Worked example: reading the graph (Supplement)

A generator's e.m.f. starts at zero, rises to +6.0 V at 0.010 s, is zero at 0.020 s, reaches −6.0 V at 0.030 s and is zero again at 0.040 s. At the start, the coil's plane is at right angles to the field.

  1. Where is the coil at 0.010 s and 0.030 s? Its plane is parallel to the field: the peak and the trough.
  2. And at 0.020 s? Half a turn on, at right angles to the field again, so the e.m.f. is zero.
  3. How fast is it turning? One cycle takes 0.040 s, so it makes 1 ÷ 0.040 = 25 turns each second: 25 Hz.
  4. Sketch it at twice the speed: peaks of about +12 V and −12 V, each cycle lasting 0.020 s.

Generating on screen

In the simulation above, press Generator in the Experiment group. It begins with Slip rings (a.c.), a Turning speed of 1 rev/s and a 200-turn coil. The meter is connected across the two brushes, and a lamp is in the circuit from the start.

  1. Press Play. Coil's plane begins at "At right angles to the field", with an Output e.m.f. of 0; a quarter turn later the trace reaches its first peak.
  2. Set the speed to ¼× and watch the little coil icons drawn above the trace: upright ones sit on the zeros, flat ones on the peaks and troughs.
  3. Tap Faster four times, so the coil makes 2 rev/s. The peaks double and twice as many cycles fit on the trace: Peak output was 0.754 V and is now 1.51 V.
  4. Tap Slower four times to return to 1 rev/s. Then raise Turns on the coil or pick a stronger Field between the magnets, one at a time: taller peaks, same frequency.

The Split ring (d.c.) option, which makes a dynamo, and the NBAω formula behind Peak output go beyond 0625.

Common mistakes

  • (Supplement) Saying the e.m.f. peaks with the coil upright (plane perpendicular to the field), since the most field passes through the coil then. The e.m.f. is zero there; its peaks come a quarter turn later, with the plane lying along the field, when the sides cut the lines fastest.
  • (Supplement) Saying that the slip rings reverse the current. Slip rings are unbroken, so each coil end rubs against one brush only, the whole time. The alternating e.m.f. comes from the coil itself, as its sides move up and then down through the field.
  • (Supplement) Sketching a faster generator's graph with taller peaks but the same spacing. Each turn now takes less time, so the cycles must also be drawn closer together.
  • (Supplement) Sketching more cycles for a stronger magnet or a coil with more turns. These make the peaks taller only; the number of cycles each second is fixed by the coil's rate of turning.
  • (Supplement) Drawing troughs that are deeper or shallower than the peaks for a coil turning steadily. Each side cuts the field just as fast on the way down as on the way up, so the trough matches the peak in size.
  • (Supplement) Thinking that a rotating-magnet generator needs slip rings for its output. Its coil stays still, so the output wires can be joined to the circuit directly.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.(Supplement) A student in Mumbai builds a simple a.c. generator from a rectangular coil on an axle, a magnet, two slip rings and two carbon brushes. The output is connected to a lamp.

    1. (a)Describe how the generator produces an alternating e.m.f. when the coil is turned.

      3 marks
      Show the answer

      Answer: As the coil turns in the magnetic field, its sides cut through the field, inducing an e.m.f. Each side moves up through the field for half a turn and down for the other half, so the e.m.f. reverses direction every half turn.

      Marking points

      • the coil turns in the magnetic field / its sides cut the field lines
      • e.m.f. induced (in the coil)
      • each side moves up then down (the other way) through the field, so the e.m.f. reverses every half turn
    2. (b)State the purpose of the slip rings and brushes.

      2 marks
      Show the answer

      Answer: They connect the turning coil to the lamp. Each end of the coil always stays joined to the same brush, so the leads do not twist and the alternating e.m.f. reaches the circuit.

      Marking points

      • connect the rotating coil to the external circuit (the lamp)
      • each end of the coil stays connected to the same brush / the wires do not twist
    3. (c)State two ways of making the peak e.m.f. larger without changing the frequency of the output.

      2 marks
      Show the answer

      Answer: Use a stronger magnet, and put more turns on the coil.

      Marking points

      • stronger magnet (magnetic field)
      • more turns on the coil
  2. 2.(Supplement) The coil of an a.c. generator turns at a steady rate. At time t = 0 the coil's plane is perpendicular to the magnetic field. The graph of e.m.f. against time reaches its first peak, 4.0 V, at t = 0.005 s.

    1. (a)State the position of the coil at t = 0.005 s.

      1 mark
      Show the answer

      Answer: Its plane is parallel to the magnetic field.

      Marking points

      • coil's plane lies along (parallel to) the field
    2. (b)Explain why the e.m.f. is zero at t = 0.

      2 marks
      Show the answer

      Answer: At that instant each side of the coil slides parallel to the field lines, so no lines are being cut and no e.m.f. is induced.

      Marking points

      • the sides move parallel to (along) the field lines
      • so no field lines are cut / no e.m.f. is induced
    3. (c)Calculate the time for one complete turn of the coil, and hence the frequency of the output.

      3 marks
      Show the answer

      Answer: The first peak comes after a quarter of a turn, so one turn takes 4 × 0.005 = 0.020 s. The coil makes 1 ÷ 0.020 = 50 turns each second, so the frequency is 50 Hz.

      Marking points

      • first peak is a quarter of a turn (0.005 s = ¼ turn)
      • one turn takes 0.020 s
      • frequency = 50 Hz
    4. (d)State the time at which the e.m.f. first reaches a trough.

      1 mark
      Show the answer

      Answer: At three quarters of a turn: t = 0.015 s.

      Marking points

      • 0.015 s
  3. 3.(Supplement) A small hydroelectric generator in Nepal has a coil that turns at 10 revolutions per second. Its peak e.m.f. is 12 V.

    1. (a)Describe the graph of e.m.f. against time for the first 0.20 s. Give the highest and lowest values and the number of cycles shown.

      3 marks
      Show the answer

      Answer: A smooth wave that rises and falls, alternating between +12 V and −12 V. One cycle takes 0.10 s, so the graph shows two complete cycles.

      Marking points

      • smooth alternating wave (sine shape) crossing zero
      • peaks of +12 V and troughs of −12 V
      • two complete cycles (one every 0.10 s)
    2. (b)The coil is made to turn at 20 revolutions per second. State two ways in which the graph changes.

      2 marks
      Show the answer

      Answer: The peaks become higher, about 24 V, and the cycles are closer together: four cycles fit into 0.20 s.

      Marking points

      • higher peaks (accept about 24 V)
      • more cycles in the same time / higher frequency (four cycles in 0.20 s)
    3. (c)An engineer suggests a design in which a magnet spins inside a fixed coil. Explain why this design does not need slip rings.

      2 marks
      Show the answer

      Answer: The coil that gives the output does not move, so its ends can be wired straight to the circuit; there are no moving connections to make.

      Marking points

      • the (output) coil is stationary / does not rotate
      • so it can be connected to the circuit directly (no moving contacts needed)

Quick check

6 questions

  1. 1.(Supplement) What is the job of the slip rings and brushes in a simple a.c. generator?
  2. 2.(Supplement) The plane of a generator's coil is at right angles to the magnetic field. What is the e.m.f. at that instant?
  3. 3.(Supplement) Why is a generator's e.m.f. largest when the plane of the coil is parallel to the field?
  4. 4.(Supplement) A generator's coil is turned twice as fast. How does its output change?
  5. 5.(Supplement) Which change makes the peaks of a generator's output taller without changing its frequency?
  6. 6.(Supplement) A generator's coil turns at 50 revolutions per second. How long does one cycle of its output take?