Skip to content

GCSE Physics — AQA · Magnetism and electromagnetism

Alternators and dynamos

4.7.3.2Higher tierPhysics only

GCSE Physics only, Higher tier. A coil turning in a magnetic field has a p.d. induced in it that reverses every half turn. An alternator's slip rings pass this on as a.c.; a dynamo's split ring swaps the connections, so its output is d.c. Faster turning raises both the peak and the frequency.

Loading simulation…

Symbols match your course. Open the full electromagnetic induction simulation for more presets and teacher tools.

Higher tier, physics only: spec point 4.7.3.2

As with all of 4.7.3, this is GCSE Physics only, tested on Higher tier papers. Be ready to explain why an alternator's output alternates while a dynamo's flows one way, and to sketch and read p.d.–time graphs for both.

There is no equation of its own, though graph questions may need T=1fT = \dfrac{1}{f} (4.6.1.2, on the equation sheet). The specification names both machines but not their rings; the explanations need them, so learn both.

One spinning coil

Both machines rotate a coil between two magnetic poles. Its long sides sweep through the field, so a p.d. is induced in the coil. How big it is depends on how quickly the sides are cutting field lines, which varies through each turn:

Coil's planeLong sides are movingp.d. in the coil
Perpendicular to the fieldalong the field lines, cutting nonezero
Parallel to the fieldstraight across the field linesat its peak
Half a turn onthe opposite way through the fieldreversed

Inside the coil, then, the p.d. always swaps direction every half turn. The two machines differ only in how the coil connects to the circuit outside.

Alternator: slip rings give a.c.

Each end of the coil has its own complete slip ring, turning with it, and a carbon brush rests on each ring. One end always feeds the same brush, so every reversal reaches the circuit: alternating current. On a p.d.–time graph this makes a smooth wave, up to a positive peak, down through zero to a negative peak and back, one cycle per turn.

Dynamo: a split ring gives d.c.

A dynamo replaces the slip rings with a split-ring commutator, two half-rings on the axle. They change brushes every half turn, exactly when the coil's p.d. is zero. Each reversal inside the coil is cancelled by a swap of connections, so the output keeps one sign: direct current. The graph is a string of humps, all above the axis, two for each turn.

Changing the graph

  • Spin the coil faster and the peaks grow taller and crowd closer together: the frequency goes up.
  • Use a stronger magnet or add turns and only the height changes; the spacing does not change.

Worked example: reading an alternator trace

An alternator's p.d.–time graph peaks at 6.0 V. One complete cycle, from zero through both peaks and back to zero, lasts 0.040 s. Find the frequency, and the coil's rate of turning.

Given: period T=0.040T = 0.040 s. Equation: f=1Tf = \dfrac{1}{T}. Substitution: f=10.040f = \dfrac{1}{0.040}. Answer: f=25f = 25 Hz. One cycle comes from each turn, so the coil makes 25 turns per second.

Two predictions follow. With a split ring at the same speed, the peak stays at 6.0 V, nothing falls below zero, and a fresh hump starts every 0.020 s. With slip rings at twice the speed, the peak doubles to 12 V and the frequency becomes 50 Hz.

The generator on screen

In the simulation above, switch Experiment to Generator and press Play. The defaults are 200 turns, a 0.2 T field, slip rings and 1 revolution per second. The meter reads the p.d. between the two brushes, and a lamp is part of the circuit from the outset.

  1. Watch Output p.d. rise to about +0.75 V, fall to about −0.75 V and repeat, while Kind of output shows a.c., 1.00 Hz. The Coil’s plane card tracks the coil: close to 90° from upright (Parallel to the field) near each peak, and close to 0° (At right angles to the field) each time the output passes zero.
  2. Tap the Slip rings button next to the stage and it switches to a split ring. Now the trace never dips below zero, and Kind of output reads d.c., 2.00 pulses a second.
  3. Tap Faster 4 times to reach 2 rev/s. Peak output doubles from 0.754 V to 1.51 V, and Kind of output now counts 4.00 pulses a second. The Peak output formula is beyond GCSE; just compare values.
  4. Press Start the graph again after each change to compare the Induced p.d. against time traces.

Common mistakes

  • Mixing up the two machines. Slip rings belong to the alternator, which makes a.c.; the split ring belongs to the dynamo, which makes d.c.
  • Drawing a dynamo's output as a flat line. Its p.d. rises and falls back to zero twice each turn; it counts as d.c. because it never goes below zero, not because it is steady.
  • Placing the peak p.d. at the instant the coil's plane sits at 90° to the field. There the p.d. is zero; the peak comes a quarter of a turn later, with the coil's plane parallel to the field and its sides cutting field lines fastest.
  • Showing only a taller peak when the coil turns faster. Faster turning also fits more cycles into each second, so the peaks sit closer together along the time axis.
  • Giving both machines the same number of peaks per turn. An alternator gives one full cycle per turn, with one positive and one negative peak; a dynamo gives two humps per turn, on the same side of zero.
  • Thinking a stronger magnet changes the frequency. It only makes the peaks taller; the frequency depends on how many times the coil turns each second.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.In an alternator, a rectangular coil is turned steadily in the field between two opposite magnetic poles. The two ends of the coil are fixed to separate slip rings, and a carbon brush presses on each ring.

    1. (a)Explain how the alternator produces an alternating potential difference. You should refer to the position of the coil in your answer.

      6 marks
      Show the answer

      Answer: As the coil turns, its sides move through the magnetic field and cut field lines, so the coil has a potential difference induced in it (the generator effect). With the coil's plane parallel to the field, the sides cut straight across the field lines and the p.d. is at its greatest. With the coil's plane perpendicular to the field, the sides slide along the field lines, cut none, and the p.d. is zero. Half a turn later each side is travelling the opposite way through the field, so the p.d. reverses. Because each end of the coil stays on its own slip ring and brush, these reversals pass to the circuit and the output alternates, one cycle per turn. (Level-of-response marking: examiners compare the full answer with level descriptors. The top level needs each p.d. value tied to a coil position and the slip rings explained.)

      Marking points

      • The sides of the coil cut field lines as it turns, so a p.d. is induced (generator effect).
      • Greatest p.d. when the coil's plane is parallel to the field.
      • Zero p.d. with the coil's plane at 90° to the field (sides moving along the field lines).
      • Half a turn later each side moves the opposite way through the field, so the p.d. reverses.
      • Slip rings keep each end of the coil connected to the same brush, so the reversals reach the circuit.
      • The output alternates, completing one cycle every turn.
  2. 2.A student connects an alternator to an oscilloscope. The trace on the screen shows a p.d. that rises to a maximum of 4.5 V and falls to a minimum of −4.5 V. One complete cycle takes 0.050 s.

    1. (a)State the peak potential difference of the output.

      1 mark
      Show the answer

      Answer: 4.5 V.

      Marking points

      • 4.5 V.
    2. (b)Calculate the frequency of the output. Use the Physics equation sheet.

      2 marks
      Show the answer

      Answer: f = 1 ÷ T = 1 ÷ 0.050 = 20 Hz.

      Marking points

      • Substitution: f = 1 ÷ 0.050.
      • f = 20 Hz.
    3. (c)The coil of the alternator is turned faster. Describe two ways in which the trace changes.

      2 marks
      Show the answer

      Answer: The peaks become taller, because the peak p.d. increases. The cycles are closer together, because there are more of them each second (a higher frequency, a shorter period).

      Marking points

      • The peak p.d. is higher (taller peaks).
      • More cycles per second / higher frequency / shorter period (peaks closer together).
    4. (d)The slip rings are replaced with a split-ring commutator, and the coil is turned at its original speed. Describe the new trace.

      3 marks
      Show the answer

      Answer: The trace no longer goes below zero: it becomes a series of humps that all lie on one side of zero. Each hump still peaks at 4.5 V. There are two humps for every turn, so a new hump starts every 0.025 s.

      Marking points

      • The p.d. never changes sign (all humps on the same side of zero).
      • The peak is still 4.5 V.
      • Two humps per turn (a hump every 0.025 s).
  3. 3.A student wants to use a generator, turned by hand, to charge a rechargeable battery. The battery can only be charged by a current that always flows in the same direction.

    1. (a)State whether the student should use an alternator or a dynamo. Give a reason for your answer.

      2 marks
      Show the answer

      Answer: A dynamo, because it produces direct current, which always flows in the same direction.

      Marking points

      • A dynamo.
      • It produces d.c. (current in one direction only).
    2. (b)Explain how the split-ring commutator makes the current in the circuit flow in only one direction.

      3 marks
      Show the answer

      Answer: The p.d. induced in the coil reverses every half turn. The split ring turns with the coil and swaps the coil's connections to the brushes every half turn. The swap happens just as the p.d. in the coil reverses, at zero, so the p.d. across the brushes, and the current in the circuit, always keeps the same direction.

      Marking points

      • The p.d. in the coil reverses every half turn.
      • The split ring swaps the connections between the coil and the brushes every half turn.
      • The swap happens when the coil's p.d. reverses (passes zero), so the output never changes direction.
  4. 4.A coil with slip rings turns at a steady rate in a uniform magnetic field. As it turns, the p.d. across the coil rises to a peak, falls to zero, and then does the same in the opposite direction, over and over.

    1. (a)State the position of the coil's plane when the p.d. is zero. Explain why the p.d. is zero in this position.

      2 marks
      Show the answer

      Answer: Perpendicular to the field. Here the coil's sides travel parallel to the field lines, so none are cut.

      Marking points

      • Perpendicular (at right angles) to the field.
      • The sides move along (parallel to) the field lines, so they cut none.
    2. (b)State the position of the coil's plane when the p.d. is at its peak.

      1 mark
      Show the answer

      Answer: Parallel to the field.

      Marking points

      • Parallel to the magnetic field.
    3. (c)Suggest two changes, other than turning the coil faster, that would increase the peak p.d.

      2 marks
      Show the answer

      Answer: Fit a stronger magnet. Wind more turns onto the coil.

      Marking points

      • A stronger magnet (stronger magnetic field).
      • More turns on the coil.

Quick check

6 questions

  1. 1.What connects the turning coil of an alternator to the outside circuit?
  2. 2.A dynamo's output graph is a row of humps that all lie above zero. Why does it count as d.c.?
  3. 3.Where is the coil of an alternator when its output p.d. is zero?
  4. 4.The output of an alternator has a period of 0.10 s. What is its frequency?
  5. 5.The coil of an alternator is turned half as fast. What happens to its output?
  6. 6.A dynamo's coil turns 15 times each second. How many humps appear on its p.d.–time graph each second?