Skip to content

Forces simulation

Momentum and Collisions Simulation

Send two trolleys into each other on a frictionless track and watch the momentum bars, velocities and kinetic energy change. Switch between springs, rubber and Velcro bumpers, or push the trolleys apart with a spring.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A 1 kg trolley rolls at 1.5 m/s into an identical trolley that is standing still. The bumpers are springs, so no kinetic energy is lost. What happens straight after the collision?

Try this

  1. 1Run the default set-up first: two 1 kg trolleys with spring bumpers. Watch the momentum bars as they touch. Trolley 1's bar shrinks to nothing while trolley 2's grows, and the green total bar never moves.
  2. 2Choose Light hits heavy. Before you press play, decide whether the 1 kg trolley will carry on, stop or bounce back. Then check the sign of its velocity in the Before and after table.
  3. 3Keep the masses and speeds the same and switch the bumpers from Springs to Rubber to Velcro. Note the kinetic energy change each time. Does the total momentum change at all?
  4. 4Choose Explosion: spring pushes them apart. Make trolley 2 three times as heavy as trolley 1 and predict how their speeds will compare before you run it.
  5. 5After a collision, open the Force graph and press Replay. Compare the shaded area with trolley 2's change in momentum, which you can work out from the Before and after table.

What this simulation shows

Two trolleys run along a level track with no friction. You set the mass and starting velocity of each one, pick the bumpers, and press play. As they meet, the bars above the track show each trolley's momentum, live, and a green bar shows the sum of the two. Afterwards the table compares every quantity before and after the collision, and the graphs let you look at the same event in three different ways.

Signs and directions

Momentum depends on direction, so the simulation treats motion to the right as positive. A trolley heading left has a negative velocity and a negative momentum, and its bar points left. A dropped minus sign is an easy way to get a collision question wrong, so try the head-on set-up and add the two momenta yourself before you play it. Equal and opposite momenta add up to zero, and the joined trolleys stop dead.

The total never changes

During contact each trolley pushes the other just as hard, but the opposite way, for exactly the same time. Whatever momentum one gains, the other loses, so the green total stays level throughout, even during the split second of contact. For two trolleys the rule is

m1u1+m2u2=m1v1+m2v2m_1 u_1 + m_2 u_2 = m_1 v_1 + m_2 v_2

where uu is a velocity before and vv a velocity after. When the trolleys stick, both share one velocity, which is the total momentum divided by the total mass.

Bumpers and kinetic energy

The bumpers decide how bouncy the collision is, measured by the coefficient of restitution, ee: the speed of separation divided by the speed of approach. Springs give e=1e = 1, an elastic collision in which kinetic energy is kept. Velcro gives e=0e = 0, so the trolleys move off joined together and the largest possible share of kinetic energy is transferred. Rubber sits in between. The energy panel shows the loss and where it goes: mostly into the thermal store of the bumpers, a little as sound, and some into denting the bumpers out of shape.

Explosions from rest

In explosion mode the trolleys start together, at rest, with a squashed spring between them. When the latch opens the spring pushes them apart. The total momentum was zero, so it stays zero: the lighter trolley always leaves faster. Kinetic energy appears from nothing you can see, because it was stored as elastic potential energy in the spring.

Force during the contact

The force graph zooms in on the moment the bumpers touch. Its shaded area is the impulse on trolley 2, and it always equals that trolley's change in momentum. The exact shape and height of the curve depend on how stiff the bumpers are, but the area is always the change in momentum. That is why, with the same masses and starting velocities, springs give a bigger area than Velcro: the trolleys bounce apart, so trolley 2's momentum changes more. On the momentum–time graph, the gradient of a trolley's line is the force on it, which is zero except while they touch.

How the model works

The track is frictionless and the trolleys only touch through their bumpers, so no outside force acts on the pair. The starting positions are chosen for each run so that the whole collision happens on the track, and the run ends when a trolley reaches an end stop, or after a few seconds if neither does. Symbols follow your course: use the switch under the simulation to see, for example, v1v_1 and v1′v_1' in place of u1u_1 and v1v_1.

Equations

Check your understanding

8 questions

  1. 1.Taking right as positive, what is the momentum of a 3 kg trolley moving to the left at 2 m/s?
  2. 2.In which type of collision is the total kinetic energy the same before and after?
  3. 3.A 4 kg trolley moving at 2 m/s hits an identical trolley at rest and they stick together. What is their velocity afterwards?
  4. 4.Two trolleys at rest are pushed apart by a spring. The 0.5 kg trolley moves left at 3 m/s. What does the 1.5 kg trolley do?
  5. 5.Two trolleys collide with a speed of approach of 4 m/s. The coefficient of restitution is 0.5. What is their speed of separation?
  6. 6.Momentum is conserved in a sticky collision, so why is kinetic energy lost?
  7. 7.What does the area under the force–time graph for one trolley during a collision represent?
  8. 8.A 1 kg trolley at +3 m/s meets a 2 kg trolley at −1 m/s and they stick together. What is their velocity?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more