Impulse and Car Safety Features: Why a Longer Stop Means a Smaller Force
Learn what impulse is, why stretching out a collision reduces the force, how crumple zones, airbags, seat belts and helmets use this idea, and how to find impulse from the area under a force–time graph.
Published · 8 min read
On this page
When a force acts on an object for some time, it changes the object's momentum. The force multiplied by that time is called the impulse:
F is the resultant force in newtons (N), Δt is the time it acts for in seconds (s), and Δp is the change in momentum in kg m/s. The mass is m, and u and v are the starting and final velocities.
This one equation explains how car safety features work. In a crash, a car and the people inside it must lose all their momentum. That loss is set by their mass and speed, so a designer cannot alter it. What a designer can change is how long the stop takes. Make the time longer, and the average force gets smaller. Smaller forces mean fewer injuries.
This guide explains impulse, the safety features that rely on it, and force–time graphs.
What is impulse?
Impulse is the force on an object multiplied by the time for which that force acts. You can get the equation from Newton's second law. Start with F = ma and replace the acceleration with the change in velocity divided by the time:
Multiply both sides by Δt and you get . So the impulse on an object equals its change in momentum. The form above says that the resultant force on an object is its rate of change of momentum.
Impulse is measured in newton seconds (N s). This unit is the same as kg m/s, so either is correct. Impulse is a vector quantity, with the same direction as the force.
Why does a longer stopping time mean a smaller force?
Rearrange the impulse equation to find the average force:
Think about a car that drives into a wall. It ends up at rest whether it stops gently or suddenly, so its change in momentum, Δp, is fixed.
That leaves Δt. If the stop takes twice as long, the average force is halved. If it takes ten times as long, the force is one tenth as big. The same applies to each belted person inside.
You can also think about energy. A longer stopping time comes with a longer stopping distance. The kinetic energy must be transferred either way, and work done = force × distance, so a longer distance needs a smaller force.
Worked example 1: a crash test with and without crumple zones
In a crash test, a small car of mass 1100 kg drives into a solid barrier at 14 m/s, which is about 50 km/h. Compare the average force on the car if it stops in (a) 0.040 s, with a very stiff front, and (b) 0.10 s, with a crumple zone.
Given: m = 1100 kg, u = 14 m/s, v = 0
Size of the change in momentum:
Equation:
(a) , or about
(b) , or about
Answer: the crumple zone makes the stop 2.5 times longer, so the average force is divided by 2.5 (it falls to 0.4 of its first value). Belted passengers share the longer stop too.
Worked example 2: how long must the stop last?
Engineers in Brazil want the average force on a 75 kg driver to be no more than 9000 N in a crash at 18 m/s. Find the shortest stopping time that the seat belt and airbag must give.
Given: m = 75 kg, u = 18 m/s, v = 0, largest force F = 9000 N
Size of the change in momentum:
Equation:
Substitution:
Answer: Δt = 0.15 s. Any shorter stop would push the force above 9000 N.
How do car safety features use impulse?
Each safety feature makes the stop last longer, spreads the force over a bigger area of the body, or does both.
- Crumple zones. The front and back of the car are built to fold up in a planned way. Folding metal takes time and absorbs energy. The passenger cell in the middle is made very stiff, so it keeps its shape around the people inside.
- Seat belts. A belt holds the person to the seat, so they slow down with the car instead of flying into the dashboard or windscreen. The webbing stretches a little, which makes the person's stop last longer, and it spreads the force across the chest and hips. Because it stretches, a belt that was worn in a serious crash should be replaced.
- Airbags. Sensors detect a sudden deceleration and fill the bag with gas in a few hundredths of a second. Vents let it give way as the head and chest push into it. The person stops over a longer time, and the force acts on a larger area, which lowers the pressure on the body. Airbags are designed to work with seat belts, not instead of them.
The same idea protects people away from the road:
- Cycle and motorcycle helmets have a hard shell over a foam liner. In a fall, the foam crushes, so the head stops over a longer time. The foam does not spring back, so a helmet that has taken a hard knock should be replaced.
- Gym crash mats, soft playground surfaces and long-jump sand give way as you land, so your body comes to rest more gradually.
- Bending your knees when you land from a jump does the same job. Landing with straight legs gives a short, sharp force on your joints.
- Catching a ball. A goalkeeper or a baseball player lets their hands move back with the ball, so the catch stings less.
Explore these ideas further in the impulse and car safety simulation.
What does a force–time graph show?
During a collision, the force is not constant. It rises from zero, reaches a peak and falls back to zero. A force–time graph shows this.
The area under a force–time graph is the impulse, so it equals the change in momentum. This works for any shape of graph. For a constant force, the area is a rectangle: force × time. For a force that rises and falls steadily, the area is a triangle: ½ × peak force × time.
Now compare two graphs for the same object being stopped from the same speed:
- A hard surface gives a tall, narrow spike. The time is short and the peak force is large.
- A soft surface gives a low, wide hump. The time is long and the peak force is small.
The two areas are equal, because the change in momentum is the same. A good safety feature turns the tall spike into the low hump.
In the momentum and collisions simulation, crash the two trolleys and open the force graph. The shaded area is the change in momentum of trolley 2. Try the spring, rubber and Velcro bumpers in turn. The shape of the graph changes, but each time the area matches trolley 2's change in momentum.
Worked example 3: a tennis serve
A tennis ball of mass 0.058 kg is at rest at the top of its toss when the racket hits it. The force–time graph for the contact is a triangle with a peak force of 800 N and a width of 0.0040 s. Find the impulse, the speed of the ball as it leaves the racket, and the average force.
Given: peak force = 800 N, Δt = 0.0040 s, m = 0.058 kg, u = 0
Impulse = area of the triangle:
Equation: impulse = mv − mu. Since u = 0,
Substitution:
Answer: v = 28 m/s (2 significant figures), which is about 99 km/h.
Average force: . For a triangle-shaped graph, the average force is half of the peak force.
Common mistakes
- Claiming that a crumple zone reduces the change in momentum. That change is fixed. The crumple zone makes the time longer, which reduces the force.
- Writing that the force is "absorbed". Forces are not absorbed. Explain that the collision time increases, so the rate of change of momentum, and so the force, decreases.
- Ignoring direction in a bounce. A ball that arrives at 12 m/s and leaves at 8.0 m/s the other way has a velocity change of 20 m/s, not 4 m/s.
- Using the peak force as the impulse. The impulse is the area under a force–time graph, not its height.
- Getting the unit wrong. Impulse is in N s, the same as kg m/s. It is not N/s.
- Forgetting to convert milliseconds. 40 ms is 0.040 s.
Key points
- Impulse = force × time = change in momentum: .
- The resultant force on an object is its rate of change of momentum, .
- For a fixed change in momentum, a longer time gives a smaller average force.
- Crumple zones, seat belts, airbags, helmets and soft landing surfaces all make the stopping time longer.
- Impulse is measured in N s, which is the same unit as kg m/s.
- The area under a force–time graph is the impulse.