Skip to content

Thermal physics simulation

Latent Heat and Heating Curve Simulation

Turn crushed ice into steam on a virtual bench and see why the temperature stalls at 0 °C and 100 °C. Read E = mL from the joulemeter, measure the latent heat of fusion with a control funnel, and watch stearic acid freeze on a cooling curve.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

Crushed ice at −20 °C is heated by a 500 W heater that stays on the whole time. The thermometer reaches 0 °C and the ice starts to melt. What does the thermometer show while the ice is melting?

Try this

  1. 1Keep the starting set-up (Heating curve, 0.50 kg of ice at −20 °C, 500 W, Lagged) and press play. While the Stage card says Ice melts, what does the Thermometer line on the graph do?
  2. 2Choose No losses under Insulation and run it again. In the Stage by stage panel, divide the joulemeter energy for the melting part by 0.50 kg. Do you get 3.34 × 10⁵ J/kg?
  3. 3Set Insulation to None. Is L from the melting readings now too high or too low? What about boiling? Give one reason for each.
  4. 4Pick Melting practical and let the run finish. Compare the two values of L in the Readings panel and explain why the control funnel matters.
  5. 5Pick Cooling curve and press play. At what temperature does the line go flat, and what is happening inside the tube while it stays flat?

What is on the bench

Pick one of three experiments. Heating curve puts crushed ice, straight from a freezer and colder than 0 °C, into a closed container with an electric heater, a joulemeter, a digital thermometer and a stopwatch. Melting practical sets up two funnels of melting ice above beakers on balances, with a heater in one funnel only. Cooling curve lets a tube of molten stearic acid cool in the air. A chip on the stage shows how much faster than real life each run plays.

Reading the heating curve

The temperature–time graph has five parts. It slopes up while the ice warms, goes flat at 0 °C while the ice melts, slopes up again as the water warms, goes flat at 100 °C while the water boils, and finally climbs as the steam warms. The flat parts are where the state changes.

Along a sloping part the temperature climbs by 1/(mc)1/(mc) for every joule supplied, so with steady power and no losses the gradient is P/(mc)P/(mc). Ice and steam both have specific heat capacities close to 2000 J/(kg °C), about half the value for water, so their lines are roughly twice as steep.

On a flat part the energy changes the state instead:

E=mLE = mL

With the starting settings, melting the 0.50 kg of ice takes 0.50×3.34×105=1.67×1050.50 \times 3.34 \times 10^5 = 1.67 \times 10^5 J, while boiling the water away needs 1.13×1061.13 \times 10^6 J. With no losses, a 500 W heater supplies those in 334 s and 2260 s, so the boiling plateau lasts almost seven times as long. The Stage by stage panel lists the energy for every stage and sets it beside the joulemeter readings.

Why the temperature stops rising

While the reading on a plateau stays fixed, the average kinetic energy of the particles stays fixed too. The internal energy still rises, because the energy goes into the potential energy of the particles as their arrangement breaks up. The particle panel on the stage tracks both: its kinetic energy bar holds still on a plateau while the internal energy bar keeps climbing.

Measuring L, and which way the error goes

You can find L from any plateau. Note the joulemeter where the flat part starts and where it ends, then divide the difference by the mass. With No losses you get the accepted values. With real insulation the two answers drift in opposite directions. While the ice is colder than the room, the room helps to melt it, so the joulemeter shows less than mL and L comes out low. While the water boils, the heater must also replace energy escaping to the room, so L comes out high.

The melting practical handles the room's share with a control funnel that has no heater. Both funnels take in the same energy from the room, so subtracting the control's meltwater leaves the ice melted by the heater alone. A small error remains: some of the heater's energy warms the air rather than the ice, so even the corrected value is a little too big.

Cooling curves

Molten stearic acid cools quickly at first, then holds at about 69 °C while it freezes, then cools again as a solid. On the flat part it is still losing energy to the air, but freezing releases latent heat just as fast. Change the mass and watch the flat part grow or shrink. To focus on the sloping parts alone, try the specific heat capacity simulation.

Equations

  • Specific heat capacity

    ΔE=mcΔθ

    change in thermal energy = mass × specific heat capacity × temperature change

    Open calculator →
  • Specific latent heat

    E=mL

    thermal energy for a change of state = mass × specific latent heat

    Open calculator →

Check your understanding

8 questions

  1. 1.The specific latent heat of fusion of water is about 3.34 × 10⁵ J/kg. What does this tell you?
  2. 2.How much energy is needed to boil away 0.20 kg of water that is already at 100 °C? (L = 2.26 × 10⁶ J/kg)
  3. 3.A heater keeps running during the flat part of a heating curve. Where does that energy go?
  4. 4.With no losses, a 500 W heater melts ice that is already at 0 °C. How long does it take to melt 0.25 kg? (L = 3.34 × 10⁵ J/kg)
  5. 5.On a heating curve for water with steady power and no losses, why does the ice line slope more steeply than the liquid water line?
  6. 6.In the funnel method for the latent heat of fusion, why is a second funnel of ice set up with no heater?
  7. 7.Molten stearic acid left to cool in air stays at about 69 °C for several minutes. Which statement is correct?
  8. 8.Students who find L for boiling water from the energy supplied and the mass boiled away usually get too high a value. Why?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more