Skip to content

Specific Latent Heat and Heating Curves: Why the Temperature Stops Rising

Understand specific latent heat of fusion and vaporisation, use E = mL with water, explain the flat parts of heating and cooling curves, and tell latent heat apart from specific heat capacity.

Published · 8 min read

On this page

Heat a substance to its melting point or boiling point and something odd happens: the temperature stops rising. It stays put until the whole sample has changed state. The energy you supply during this time is called latent heat. "Latent" means hidden. Energy goes in, but the thermometer reading does not move.

The specific latent heat of a material tells you how much energy it takes to change the state of 1 kg of it, at a constant temperature. For any mass, use:

E=mLE = m L

The energy E is in joules (J), the mass m in kilograms (kg), and L in joules per kilogram (J/kg). Some books write the same equation as Q = mL.

Each substance has two values. The specific latent heat of fusion, LfL_f, is for melting (solid to liquid). The specific latent heat of vaporisation, LvL_v, is for boiling (liquid to gas). The same amount of energy comes back out when the substance freezes or condenses. For water, the standard values are:

  • Lf≈3.34×105 J/kgL_f \approx 3.34 \times 10^5\ \text{J/kg}, or 334 kJ/kg
  • Lv≈2.26×106 J/kgL_v \approx 2.26 \times 10^6\ \text{J/kg}, or 2260 kJ/kg

In an exam, use the value the question gives you.

Why does the temperature stay constant during a change of state?

Temperature is linked to how fast the particles move: to their average kinetic energy.

In a solid, strong forces of attraction hold the particles in fixed positions. To melt it, you must supply energy to weaken these bonds so the particles can slide past each other. To boil a liquid, you must pull the particles completely apart. During a change of state, the energy you supply does this job. It raises the potential energy of the particles, not their kinetic energy. The particles do not speed up on average, so the temperature stays the same.

The internal energy of a substance is the total kinetic and potential energy of all its particles. It rises during melting and boiling, even though the temperature does not. It falls during freezing and condensing, as bonds form again between the particles. That is why freezing and condensing release energy.

Why is the latent heat of vaporisation so much bigger?

For water, LvL_v is almost seven times LfL_f. When ice melts, the molecules stay close together, so only some of the bonds need to break. When water boils, the molecules must be separated completely and spread far apart as a gas. That takes much more energy.

Two comparisons make this clear. Melting 1 kg of ice at 0 °C needs as much energy as warming 1 kg of liquid water by about 80 °C. Boiling away 1 kg of water at 100 °C needs more than five times the energy that heated it from 0 °C to 100 °C.

Worked example 1: melting ice

How much energy is needed to melt 0.50 kg of ice that is already at 0 °C? Use Lf=3.34×105L_f = 3.34 \times 10^5 J/kg.

Given: m = 0.50 kg, Lf=3.34×105 J/kgL_f = 3.34 \times 10^5\ \text{J/kg}

Equation: E=mLfE = m L_f

Substitution: E=0.50×3.34×105E = 0.50 \times 3.34 \times 10^5

Answer: E=1.67×105 JE = 1.67 \times 10^5\ \text{J}, or 167 kJ

The temperature stays at 0 °C the whole time. All of this energy goes into changing the state.

Worked example 2: a kettle left on

An electric kettle in Lagos has a power of 2.2 kW. It reaches 100 °C, but its switch fails and the water keeps boiling for another 90 s. What mass of water turns to steam in this time? Assume all the energy goes into the water. Use Lv=2.26×106L_v = 2.26 \times 10^6 J/kg.

Given: P = 2200 W, t = 90 s, Lv=2.26×106 J/kgL_v = 2.26 \times 10^6\ \text{J/kg}

Energy supplied: E=Pt=2200×90=198 000 JE = P t = 2200 \times 90 = 198\,000\ \text{J}

Equation: m=ELvm = \dfrac{E}{L_v}

Substitution: m=198 0002.26×106m = \dfrac{198\,000}{2.26 \times 10^6}

Answer: m = 0.088 kg, or about 88 g (2 significant figures)

Even 90 s of hard boiling removes less than a tenth of a kilogram.

How do you read a heating curve?

A heating curve is a graph of temperature against time for a substance heated at a steady rate. Picture some ice at −20 °C, heated at a steady rate until it has all become steam above 100 °C. The graph has five parts:

  1. Sloping line (solid). The ice warms from −20 °C to 0 °C.
  2. Flat line at 0 °C. The ice melts. Solid and liquid are both present.
  3. Sloping line (liquid). The water warms from 0 °C to 100 °C.
  4. Flat line at 100 °C. The water boils. Liquid and gas are both present.
  5. Sloping line (gas). The steam warms above 100 °C.

The flat sections mark the melting point and the boiling point. Their lengths tell you about latent heat. With a steady power, the boiling section lasts almost seven times as long as the melting section, because LvL_v is almost seven times LfL_f.

The slopes tell you about specific heat capacity. Ice has a specific heat capacity of about 2100 J/kg °C, roughly half that of liquid water. So the ice section of the graph is about twice as steep as the water section.

For more on these graphs, open the latent heat and heating curve simulation.

What does a cooling curve show?

A cooling curve works the same way in reverse. In many school labs, a tube of melted stearic acid, a waxy solid that melts at close to 70 °C, is left to cool in the air while a student records its temperature. The temperature falls, stays flat while the liquid freezes, then falls again.

The flat part happens because freezing releases latent heat. As bonds form between the particles, energy is given out. This replaces the energy being lost to the air, so the temperature holds steady until all of the liquid has become solid.

Worked example 3: from ice to a cold drink

A student in Dubai drops 0.20 kg of ice at −10 °C into a jug. How much energy must the ice take in to become water at 25 °C? Use cice=2100c_{\text{ice}} = 2100 J/kg °C, cwater=4200c_{\text{water}} = 4200 J/kg °C and Lf=3.34×105L_f = 3.34 \times 10^5 J/kg.

Split the problem into three stages, then add them.

Stage 1, warming the ice to 0 °C: E1=mcΔθ=0.20×2100×10=4200 JE_1 = m c \Delta\theta = 0.20 \times 2100 \times 10 = 4200\ \text{J}

Stage 2, melting at 0 °C: E2=mLf=0.20×3.34×105=66 800 JE_2 = m L_f = 0.20 \times 3.34 \times 10^5 = 66\,800\ \text{J}

Stage 3, warming the water to 25 °C: E3=mcΔθ=0.20×4200×25=21 000 JE_3 = m c \Delta\theta = 0.20 \times 4200 \times 25 = 21\,000\ \text{J}

Total: E=4200+66 800+21 000=92 000 JE = 4200 + 66\,800 + 21\,000 = 92\,000\ \text{J}

Answer: E=9.2×104 JE = 9.2 \times 10^4\ \text{J}, or 92 kJ. More than 70% of it goes into melting the ice.

How is latent heat different from specific heat capacity?

Both describe energy going into a substance, but they apply at different stages.

Specific heat capacitySpecific latent heat
What the energy doesChanges the temperatureChanges the state
Temperature during the processRises or fallsStays constant
EquationE = mcΔθE = mL
UnitJ/kg °CJ/kg
Where it applies on a heating curveSloping sectionsFlat sections

To practise the sloping parts, try the specific heat capacity simulation.

Where do you see latent heat in everyday life?

  • Steam burns. Steam at 100 °C burns far worse than water at 100 °C. When steam condenses on skin, it first gives up its latent heat, then cools like hot water. Cooling to body temperature, about 37 °C, a gram of steam transfers almost ten times as much energy as a gram of boiling water.
  • Sweating. As sweat evaporates, the escaping molecules carry energy away from your skin, which cools you.
  • Clay water pots. In Pakistan and India, many homes keep drinking water in a clay pot called a matka. Water seeps through the clay and evaporates from the outside, taking energy from the water inside and keeping it cool.

Common mistakes

  • Saying the temperature rises during melting or boiling. It stays constant until the change of state is complete.
  • Saying no energy goes in on the flat part. Energy is still being supplied. It raises the potential energy of the particles, so the internal energy goes up.
  • Using E = mcΔθ on a flat section. Δθ is zero there, so that equation gives zero. Use E = mL.
  • Using the wrong value of L. Use LfL_f for melting or freezing and LvL_v for boiling or condensing.
  • Forgetting to convert units. 250 g is 0.25 kg, and 334 kJ/kg is 334 000 J/kg.
  • Thinking water always boils at 100 °C. That is only true at standard atmospheric pressure. High in the mountains, where the pressure is lower, it boils at a lower temperature.

Key points

  • Specific latent heat is the energy that takes 1 kg of a substance from one state to another at a constant temperature.
  • E = mL, with L in J/kg. Use LfL_f for melting and LvL_v for boiling.
  • For water, Lf≈3.34×105L_f \approx 3.34 \times 10^5 J/kg and Lv≈2.26×106L_v \approx 2.26 \times 10^6 J/kg.
  • During a change of state, the energy raises the potential energy of the particles. The internal energy changes, but the temperature does not.
  • Heating and cooling curves are flat at the melting point and the boiling point.
  • Specific heat capacity is about changing temperature. Specific latent heat is about changing state.