Skip to content

Specific Heat Capacity Explained: E = mcΔθ, the Practical and Examples

Learn what specific heat capacity is, how to use E = mcΔθ, why water heats up so slowly, and how to measure it in the lab while keeping errors small.

Published · 8 min read

On this page

The specific heat capacity of a substance is the energy needed to raise the temperature of 1 kg of it by 1 °C. Every material has its own value. Water needs about 4200 J for each kilogram and each degree. Copper needs only about 390 J.

You use it in one equation:

ΔE=mcΔθ\Delta E = m c \Delta\theta

Here ΔE is the change in thermal energy in joules (J), m is the mass in kilograms (kg), c is the specific heat capacity in J/kg °C, and Δθ is the temperature change in °C. A material with a high specific heat capacity needs a lot of energy to warm up, and it gives out a lot of energy as it cools down.

This guide explains the equation, why water is special, and how to measure specific heat capacity in the lab without losing marks.

What does specific heat capacity actually mean?

Imagine giving 4200 J of energy to 1 kg of water and to 1 kg of copper. The water warms by 1 °C. The copper warms by more than 10 °C. The same energy produces very different temperature rises, because the two materials store energy differently.

"Specific" means "per kilogram". So specific heat capacity lets you compare materials fairly, whatever their mass.

MaterialSpecific heat capacity (J/kg °C)
Water4200
Ice2100
Aluminium900
Iron450
Copper390
Lead130

These are rounded textbook values. In an exam, always use the value the question gives you.

Why is the specific heat capacity of water so high?

Water's value is higher than almost any other common substance. There are two main reasons. First, water molecules are very light, so one kilogram of water contains a huge number of them. Second, water molecules attract each other strongly. Some of the energy you supply goes into these attractions, instead of making the molecules move faster. So the temperature rises slowly.

This has big effects in everyday life:

  • Coastal weather. The sea warms and cools slowly. Coastal cities such as Karachi and Mumbai have smaller temperature swings than inland cities such as Jacobabad or Delhi.
  • Heating systems. Radiators in UK homes are filled with hot water. Water carries a lot of energy for each kilogram, and it releases it slowly as it cools.
  • Cooling engines. Car engines use water-based coolant to carry energy away from hot metal.
  • Hot water bottles. A bottle of hot water stays warm for hours.

How do you use the equation?

Follow the same steps every time: write down what you are given, write the equation, rearrange if needed, substitute, then give the answer with a unit.

The rearranged forms are:

c=ΔEmΔθΔθ=ΔEmcm=ΔEcΔθc = \frac{\Delta E}{m \Delta\theta} \qquad \Delta\theta = \frac{\Delta E}{m c} \qquad m = \frac{\Delta E}{c \Delta\theta}

Worked example 1: boiling a kettle

A kettle contains 1.5 kg of water at 20 °C. How much energy is needed to heat it to 100 °C? How long does a 2.0 kW kettle take, if no energy is wasted?

Given: m = 1.5 kg, c = 4200 J/kg °C, Δθ = 100 − 20 = 80 °C

Equation: ΔE=mcΔθ\Delta E = m c \Delta\theta

Substitution: ΔE=1.5×4200×80\Delta E = 1.5 \times 4200 \times 80

Answer: ΔE = 504 000 J, or about 5.0×105 J5.0 \times 10^5\ \text{J} (2 significant figures)

Time: power is energy per second, so time = energy ÷ power.

t=504 000 J2000 W=252 st = \frac{504\,000\ \text{J}}{2000\ \text{W}} = 252\ \text{s}

That is about 4.2 minutes. A real kettle takes a little longer, because some energy heats the kettle itself and the air around it.

Worked example 2: same energy, different material

A student supplies 210 kJ of energy to 5.0 kg of water. Find the temperature rise. Then find the rise if the same energy goes into 5.0 kg of iron.

Given: ΔE = 210 kJ = 210 000 J, m = 5.0 kg, c = 4200 J/kg °C for water and 450 J/kg °C for iron

Equation: Δθ=ΔEmc\Delta\theta = \dfrac{\Delta E}{m c}

Water: Δθ=210 0005.0×4200=10 ∘C\Delta\theta = \dfrac{210\,000}{5.0 \times 4200} = 10\ ^\circ\text{C}

Iron: Δθ=210 0005.0×450=93 ∘C\Delta\theta = \dfrac{210\,000}{5.0 \times 450} = 93\ ^\circ\text{C} (2 significant figures)

The temperature rise of the iron is more than nine times bigger. This is why a metal pan heats up quickly on a stove, while the water inside it takes much longer.

You can test this idea in the specific heat capacity simulation. Heat equal masses of different materials with the same power and compare how fast each temperature rises.

How do you measure specific heat capacity in the lab?

A common school experiment uses a metal block, often 1.0 kg of aluminium, with two holes drilled in it.

  1. Measure the mass of the block with a balance.
  2. Wrap the block in insulation, such as cotton wool or foam.
  3. Put an electric immersion heater in one hole and a thermometer in the other. Add a few drops of water or oil to the thermometer hole for good thermal contact.
  4. Record the starting temperature.
  5. Connect the heater to a power supply with a joulemeter. Or use an ammeter and a voltmeter instead, and a stopwatch.
  6. Switch on for a set time, such as 10 minutes. Record the temperature every minute.
  7. Switch off. Keep watching the thermometer and record the highest temperature reached.

If you used a joulemeter, read the energy directly. If you used meters, calculate it:

E=VItE = V I t

Here V is the potential difference in volts, I is the current in amps and t is the time in seconds. Then calculate c=EmΔθc = \dfrac{E}{m\Delta\theta}.

For a better result, plot a graph of temperature (y-axis) against energy supplied (x-axis). The straight part of the line has a gradient equal to 1mc\dfrac{1}{mc}. So c=1m×gradientc = \dfrac{1}{m \times \text{gradient}}. A graph uses all your readings, not just the first and last.

Worked example 3: analysing the results

A student in Nairobi heats a 1.0 kg aluminium block. The heater runs at 12 V and 4.0 A for 600 s. The temperature rises from 21 °C to 52 °C. Find the specific heat capacity of aluminium.

Energy supplied: E=VIt=12×4.0×600=28 800 JE = VIt = 12 \times 4.0 \times 600 = 28\,800\ \text{J}

Given: m = 1.0 kg, Δθ = 52 − 21 = 31 °C

Equation: c=EmΔθc = \dfrac{E}{m \Delta\theta}

Substitution: c=28 8001.0×31c = \dfrac{28\,800}{1.0 \times 31}

Answer: c = 930 J/kg °C (2 significant figures)

This is about 3% higher than the textbook value of 900 J/kg °C. The next section explains why.

What are the sources of error, and how can you reduce them?

  • Energy lost to the surroundings. This is the biggest problem. Some energy from the heater warms the air, the bench and the insulation instead of the block. The temperature rise is smaller than it should be, so the calculated value of c is too high. Reduce it with thicker insulation around the block and a lid of insulation on top.
  • Poor thermal contact. Air gaps around the heater and the thermometer slow the transfer of energy. A drop of water or oil in each hole helps.
  • Thermometer lag. The thermometer reading keeps rising for a short time after the heater is switched off, because heat is still spreading from the hot heater through the block. Record the highest temperature, not the reading at the moment you switch off.
  • Reading the thermometer. Read it at eye level to avoid parallax error. A digital thermometer or temperature probe is easier to read precisely.
  • Energy used to heat the heater and thermometer. This is hard to avoid, but it is small compared with the energy that goes into a large block.

What happens when water reaches 100 °C?

The equation only works while the substance stays in the same state. When water reaches its boiling point, its temperature stops rising even though you keep heating it. The energy now separates the molecules to turn the liquid into gas. That energy is called latent heat, and it uses a different equation. You can see this flat section on a heating curve in the latent heat and heating curve simulation.

Common mistakes

  • Using the final temperature instead of the change. Δθ is final temperature minus starting temperature.
  • Using grams instead of kilograms. 250 g is 0.25 kg. Specific heat capacity is per kilogram.
  • Forgetting to convert kJ or minutes. 210 kJ is 210 000 J. 10 minutes is 600 s.
  • Saying heat losses make c too low. Lost energy makes the measured value too high.
  • Using the equation during a change of state. At the melting or boiling point, use latent heat instead.
  • Mixing up heat and temperature. Temperature is measured in °C. Energy is measured in joules.

Key points

  • Specific heat capacity is the energy needed to raise the temperature of 1 kg of a substance by 1 °C.
  • ΔE=mcΔθ\Delta E = mc\Delta\theta, with c in J/kg °C. Some courses write Q=mcΔTQ = mc\Delta T.
  • Water has a high value, about 4200 J/kg °C, so it warms and cools slowly.
  • In the lab, find the energy with a joulemeter or with E=VItE = VIt, then use c=EmΔθc = \frac{E}{m\Delta\theta}.
  • Energy lost to the surroundings makes the measured value too high. Insulation reduces this error.
  • The equation does not apply during melting or boiling.