Skip to content

Thermal physics simulation

Conduction, Convection and Radiation Simulation

Three bench experiments in one: pins waxed to copper, aluminium, steel and glass rods, a convection current traced with dye, and a Leslie cube with an infrared detector, plus two plates facing a heater.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

Four rods sit in a block that a burner heats towards 250 °C. The nearest pin on the glass rod, 2 cm from the hot end, falls after about 6 minutes. The heating carries on until the run ends at 30 minutes. What happens to the glass rod's second pin, 5 cm from the hot end?

Try this

  1. 1Start in Conduction with the Block temperature at 250 °C. Before pressing Play, predict the order in which the four rods will drop the pins nearest the block, then check the table of drop times.
  2. 2Set the Block temperature to 100 °C and run it again. Which rods still have pins on when the run ends at 30 minutes? Then try 300 °C: does the glass rod lose a second pin?
  3. 3Choose Convection and press Play. Follow the purple dye, then press the Flame on button part-way through to turn the burner off, and watch the speed graph.
  4. 4Choose Radiation with the Test set to Emitting. Press Record, then Turn, and repeat until all four faces are in the results table. Which surface gives the lowest reading?
  5. 5Switch the Test to Absorbing and press Play. Which plate loses its pin, and at what temperature does the other plate level off?

Three experiments on one bench

Use the buttons above the Play button to switch between the experiments. Each one runs faster than real life, and the speed is shown on the stage: twenty times for the rods and the Leslie cube, six times for the beaker and ten times for the plates.

Pins racing along four rods

A Bunsen burner warms a brass block, and four rods of copper, aluminium, steel and glass stick out of it. They share the same length, thickness and block, so the material is the only difference. Drawing pins hang under each rod on blobs of wax, 2, 5, 8, 11 and 14 cm from the block. A pin falls once the rod above it reaches 55 °C.

A false-colour scale along each rod shows its temperature, much as a thermal camera would. Watch the warm colours creep outwards. They move fastest along copper and slowest along glass. Particles that vibrate harder nudge their neighbours, and in metals free electrons rush energy along as well. The table under the stage records every drop time, and the graph follows each metal 8 cm from the block.

With losses switched on, each rod gives energy to the air from its whole length. Eventually every rod stops warming, because energy then leaves as fast as it arrives. On glass that balance is reached when the rod is barely warm a few centimetres out, so most of its pins stay put however long you wait.

Following the dye

A crystal of potassium permanganate rests on the bottom of a beaker, just above a burner placed under one side. The water over the flame warms, expands slightly and becomes less dense, so it rises. The readouts give the numbers: the rising water is less dense than the rest by under 1 kg per cubic metre, yet that small difference keeps the loop turning. Cooler water sinks on the far side and creeps back along the bottom. The flow pattern is a simplified model rather than a full simulation of the water. Each density is the measured value for pure water at that temperature, but how much warmer the rising water is comes from the model.

Infrared from four faces

The Leslie cube holds hot water, so all four faces are at one temperature. A detector a fixed distance away measures the infrared reaching it from whichever face points its way. Record each face, then turn the cube. Shiny silver reads by far the lowest. Matt white comes surprisingly close to matt black, because white paint only looks pale in visible light. The water cools slowly, so a later reading is a little lower; turning quickly keeps the comparison fair.

Absorbing as well as emitting

Choose Absorbing to place a heater halfway between two plates, matt black on one side and shiny silver on the other, each with a pin waxed to its back. The black plate soon drops its pin. The shiny plate turns most of the infrared away and stays cool. Surfaces that emit well also absorb well, so the same finish wins both tests. For the energy each material stores as it warms, try the specific heat capacity simulation.

Check your understanding

7 questions

  1. 1.Rods of copper, steel and glass, all the same size, are heated at one end with pins waxed along them. In which order do their nearest pins drop?
  2. 2.Why do metals conduct thermal energy much better than glass?
  3. 3.Why does water heated at the bottom of a beaker rise?
  4. 4.In a Leslie cube experiment, which of these must stay the same for every face tested?
  5. 5.A Leslie cube is full of hot water. Which face gives the lowest infrared reading?
  6. 6.A matt black plate and a shiny silver plate are the same distance from a radiant heater. What happens?
  7. 7.One end of a rod is kept hot, and the rod loses energy to the air from its surface. After a long time, what happens to the temperature at each point along it?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more