Thermal Insulation at Home: How Lofts, Walls and Windows Keep the Warmth In
See how each common type of home insulation cuts conduction, convection or radiation, how thermal conductivity and wall thickness change the rate of energy loss, and how to work out energy savings and payback time.
Published · 8 min read
On this page
A heated home is warmer than the air outside, so energy leaks out all the time, through the roof, walls, windows and floor, and through gaps around doors. Thermal insulation cannot stop this. It slows it down, so the heating has less energy to replace and the bills are lower.
Most insulating materials use the same trick: they trap air in tiny spaces. Air conducts energy very badly, and air that cannot move cannot carry energy away by convection either. Shiny surfaces add a second trick. They reflect infrared radiation back towards where it came from.
In hot countries, the same ideas work the other way round. Insulation keeps the Sun's energy out, so homes need less cooling.
Where does a house lose energy?
Energy flows out wherever the warm inside meets the cold outside. Warm air rises in each room, so the ceiling is one of the warmest surfaces, and energy conducts through it into the loft. Walls have the largest area. Windows are thin, and glass conducts far better than air. Floors pass energy down into the ground. Gaps let warm air out and cold air in.
The bigger the temperature difference between inside and outside, the faster energy escapes. That is why heating bills peak in the coldest months.
How does each type of insulation work?
| Measure | Main transfer it reduces | How it works |
|---|---|---|
| Loft insulation | Conduction and convection | A thick blanket of fibres holds still air above the ceiling |
| Cavity wall insulation | Convection | Filling the gap between brick layers stops air circulating |
| Double glazing | Conduction and convection | A thin, sealed layer of gas sits between two panes |
| Draught excluders | Convection (moving air) | Brushes and seals block gaps round doors and windows |
| Carpets and underlay | Conduction | Fibres full of trapped air cover the cold floor |
| Reflective radiator panels | Radiation | Shiny foil behind a radiator sends infrared back into the room |
Loft insulation. Rolls of mineral wool, made of glass or rock fibres, are laid across the loft floor. In the UK, a depth of about 270 mm is often recommended. The fibres themselves conduct a little, but they hold countless pockets of still air between them. That air is a poor conductor, and it is too tightly trapped to form convection currents.
Cavity wall insulation. Many UK houses have outer walls built as two layers of brick or block, with a gap of 5 cm or more between them. Still air in the gap would insulate well, but the air is free to move. Air warmed by the inner layer rises, and air cooled by the outer layer sinks, so a convection current carries energy across. Installers drill small holes and blow in mineral wool, foam or polystyrene beads. The air can no longer circulate.
Double glazing. Two panes of glass are sealed with a gap of about 16 mm, filled with air or argon. Glass conducts roughly 40 times better than still air, so the gas layer does most of the insulating. The gap is narrow, so only weak convection currents can form. Many modern units also have a very thin coating on the glass that reflects infrared back into the room.
Draught excluders. A gap under a door lets a stream of cold air in and warm air out. Moving air carries energy with it, which is a form of convection. Brush strips and foam seals block these gaps. Never block air vents, though. Rooms with a gas fire or boiler need fresh air for safety.
Carpets. A bare stone or concrete floor conducts energy quickly into the ground. Carpet and underlay are full of trapped air, so they slow this conduction. They also feel warmer to bare feet, because they draw energy from your skin so slowly.
Reflective radiator panels. A radiator on an outside wall warms the wall behind it, and some of that energy conducts straight outdoors. A sheet of shiny foil behind the radiator, shiny side facing it, reflects much of the infrared back into the room. Shiny surfaces absorb and emit infrared poorly. Despite its name, though, a radiator also passes a lot of energy to the room by convection.
How do thermal conductivity and wall thickness matter?
Thermal conductivity is a measure of how easily energy is conducted through a material. The higher it is, the faster energy passes through a layer of it. Energy is conducted through a wall, a window or a layer of insulation faster when:
- the material has a higher thermal conductivity;
- the layer is thinner;
- the area is bigger;
- the temperature difference across it is bigger.
So a building with thicker walls, made of materials with a lower thermal conductivity, cools more slowly.
| Material | Approximate thermal conductivity, in W/(m K) |
|---|---|
| Copper | 400 |
| Glass | 1.0 |
| Brick | 0.7 |
| Wood | 0.15 |
| Mineral wool | 0.04 |
| Still air | 0.025 |
Real values vary with the exact type of material. Notice how close mineral wool comes to still air: it is mostly air.
Worked example 1: brick or wool? (going further)
Most courses only ask you to describe these effects. As an extension, the rate of conduction through a flat layer is:
Compare 10 m² of brick, 0.10 m thick, with 10 m² of mineral wool of the same thickness. It is 20 °C inside and 5 °C outside.
Temperature difference: 20 − 5 = 15 °C
Brick: W
Mineral wool: W
Answer: energy passes through the brick 17.5 times as fast. Doubling the wool to 0.20 m halves its rate to 30 W.
Real walls also have thin films of still air on each surface, which slow the flow further, so a full calculation gives smaller numbers. The lesson is the same, though: low conductivity and extra thickness both cut the rate.
Is insulation worth the money?
The payback time is how long the savings take to cover the cost:
The prices in the two examples below are made up for practice. Real costs and savings vary from home to home.
Worked example 2: loft insulation in Leeds
Before insulation, energy escapes through the loft of a house in Leeds at an average of 1.2 kW while the heating is on. After the insulation is laid, the rate falls to 0.20 kW. The heating runs for 1500 hours a year, and each kilowatt-hour of heat costs the family 8 pence. The insulation costs 360 pounds. Find the energy saved each year and the payback time.
Power saved: 1.2 − 0.20 = 1.0 kW
Energy saved: kWh, which is J
Money saved: 1500 × 8 = 12 000 pence, or 120 pounds a year
Payback time: 360 ÷ 120 = 3 years
Answer: 1500 kWh a year, with a payback time of 3 years. After that, the insulation saves money every year.
Worked example 3: a cooler flat in Multan
In summer, the Sun heats the flat concrete roof of a top-floor flat in Multan, Pakistan, and energy conducts down through the slab into the rooms. The family pays 60 000 rupees for roof insulation and white reflective paint. This cuts their air conditioner's electricity use by 4.0 units (kWh) a day for 150 days a year. Electricity costs 50 rupees per unit. Find the payback time.
Units saved: 4.0 × 150 = 600 units a year
Money saved: 600 × 50 = 30 000 rupees a year
Payback time: 60 000 ÷ 30 000 = 2 years
Answer: 2 years. The white paint reflects much of the sunlight, so the roof absorbs less, and the insulation slows conduction through it.
To see why materials differ, open the heat transfer simulation. In Conduction: rods and wax, the pins drop from the copper rod first, while the glass rod barely warms along its length. In Radiation: infrared from surfaces, the shiny silver face gives the lowest detector reading, which is why foil behind a radiator helps. For more on keeping things warm, see the insulation and cooling simulation.
Common mistakes
- Saying insulation stops energy loss. It only slows it.
- Saying insulation keeps the cold out. Energy flows from hot to cold. In winter, insulation keeps energy in.
- Thinking glass is what insulates a double-glazed window. The gas layer does most of the work.
- Saying foil panels work by conduction. They reflect infrared radiation.
- Thinking a wider gap between panes is always better. A wide gap lets bigger convection currents form.
- Thinking that doubling the loft insulation halves the energy lost from the whole home. It only reduces the loss through the roof; walls, windows, floors and draughts still lose energy as before.
- Writing payback time as saving ÷ cost. It is cost ÷ saving per year.
Key points
- Insulation slows the transfer of energy from a warm home to the colder outdoors. It cannot stop it.
- Most insulators trap air, which conducts poorly and cannot form convection currents when trapped.
- Cavity wall insulation mainly stops convection. Reflective foil mainly reduces radiation.
- Energy is conducted faster through thinner layers and materials with a higher thermal conductivity.
- Payback time = installation cost ÷ money saved each year.
- In hot climates, the same measures keep energy out and cut the need for cooling.