Skip to content

Forces simulation

Static and Kinetic Friction Simulation

Pull a block across a bench with a spring balance and watch friction respond. Static friction matches the pull up to a limit, then the block slips and kinetic friction takes over. A live graph of friction against applied force shows the rise, the drop and the flat kinetic line.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A 2.0 kg wooden block rests on a wooden bench. It takes a pull of about 10 N to make it slip. A steady 4.0 N pull now acts on it. How big is the friction force on the block?

Try this

  1. 1With the starting set-up (a 2 kg wooden block on wood), press Pull beside Play. Watch the friction arrow grow to match the pull arrow, and read the pull at the moment the block slips.
  2. 2As soon as it slips, press Pull again to hold the force steady. Does the block move at a constant speed or keep speeding up? Check the gradient of the velocity–time graph.
  3. 3While the block slides, press Ease. At what pull is the block moving fastest (the highest point of the velocity–time graph)? When the pull is down to about 3 N, press Ease again to hold it. What does the block do after it stops?
  4. 4Set Masses on top to 2 kg and pull steadily again. Compare the Limit line on the friction against applied force graph with your first run.
  5. 5Choose Steel block on ice, then Rubber block on concrete. For each one, divide the friction just before it slips by the normal contact force. What do you notice?

What this simulation shows

A block sits on a level bench, hooked to a spring balance held in a gloved hand. You control the pull. Drag the Applied force slider, or press Pull beside Play to make the pull grow at a steady rate, like tugging harder and harder on a real newton-meter. Arrows drawn to one shared scale show the pull, friction, the weight, the normal contact force and the resultant. A live graph plots friction against the applied force as you go.

Friction matches the pull at first

Start with the 2 kg wooden block and pull gently. Nothing moves, and the friction arrow grows to exactly the length of the pull arrow. Many students find this surprising. Friction is not a fixed force lying in wait; it is a response. While the block is at rest the resultant force has to be zero, so static friction takes whatever value cancels the pull. On the friction against applied force graph this is the straight part with a gradient of 1, where the friction and pull lines lie on top of each other.

The limit

Static friction cannot grow without end. The most it can provide is

Fmax=μsNF_{\text{max}} = \mu_s N

where μs\mu_s is the coefficient of static friction for that pair of surfaces and NN is the normal contact force. On a level surface with a horizontal pull, N=mgN = mg. For the 2 kg block on wood, with μs=0.5\mu_s = 0.5 and g=10g = 10 N/kg, the limit is 0.5×20=100.5 \times 20 = 10 N. A dashed outline behind the friction arrow marks this limit, and the contact under the block starts to glow as the pull closes in on it.

Sliding and kinetic friction

The moment the pull passes μsN\mu_s N, the block breaks free. Surfaces that are sliding grip less well, so friction falls to

Ff=μkNF_{\text{f}} = \mu_k N

with μk\mu_k usually smaller than μs\mu_s. That is the sudden step down on the graph. After it, the line is flat: kinetic friction stays the same however hard you pull. Any pull bigger than μkN\mu_k N leaves a forward resultant, so the block accelerates with

a=F−μkNma = \frac{F - \mu_k N}{m}

This has a surprising consequence. If you hold the pull at the value that only just started the block moving, it does not creep along at a steady speed. It speeds up, because that pull is now bigger than the friction acting on it.

Easing off and stopping

Press Ease while the block slides to lower the pull. While the pull is still bigger than μkN\mu_k N, the block keeps speeding up, just more gently. As the pull falls past μkN\mu_k N the forces balance for an instant, so the block is at its top speed: the highest point of the velocity–time graph, where the line is flat for a moment. Below μkN\mu_k N the resultant force points backwards and the block slows down. (A pull held at exactly μkN\mu_k N would keep it at a steady speed.) Once it stops, friction becomes static again and simply matches whatever pull is left, so the block stays still rather than being dragged backwards. To set it moving again you have to pull harder than μsN\mu_s N once more.

Mass and surfaces

Masses stacked on top raise the normal contact force, so the limit and the kinetic friction both grow in proportion. Choosing different surfaces changes the coefficients instead. The rubber, wood and ice values here are typical figures chosen for teaching, not measurements. Real coefficients depend on how clean, dry and smooth the surfaces are.

Friction in your course

Courses at this level, such as AQA GCSE, Cambridge IGCSE and Punjab Class 9, usually describe friction in words and do not ask you to calculate with μs\mu_s or μk\mu_k. The simulation uses the coefficients so that the numbers work out. The names vary too. Some books use sliding friction to mean kinetic friction only. Others use sliding friction for all friction between solid surfaces, with static and kinetic friction as its two kinds.

Check your understanding

8 questions

  1. 1.A 5.0 kg crate rests on a level floor (g = 10 N/kg). The coefficient of static friction is 0.4. What is the largest horizontal pull it can take without moving?
  2. 2.The same crate is pulled with a horizontal force of 8 N and stays still. How big is the friction force?
  3. 3.Which statement about kinetic friction is true in this model?
  4. 4.A 2.0 kg block slides along a bench while a 14 N pull acts on it. Kinetic friction is 6.0 N. What is its acceleration?
  5. 5.On a graph of friction against applied force, what is the gradient of the line before the object starts to slide?
  6. 6.A sliding block is pulled with a force exactly equal to the kinetic friction on it. What does it do?
  7. 7.A mass placed on top of a block doubles the normal contact force between the block and the bench. What happens to the largest static friction?
  8. 8.A block slides to a stop while a small pull still acts on it. Why does it not then slide backwards?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more