Skip to content

Static and Kinetic Friction: Why Is It Harder to Start Something Moving?

Learn how static friction grows to match a push until the object slips, why sliding friction is smaller, where friction is useful or wasteful, and how lubrication, rollers and streamlining reduce it.

Published · 8 min read

On this page

Friction is the force between touching surfaces that resists sliding. It acts along the surfaces. On a sliding object, it acts against the motion. On an object that has not started to slide, it acts against the push or pull.

For solid surfaces, friction comes in two kinds. Static friction acts while the object stays still. It is not a fixed amount: it grows to match your push exactly, so the forces balance. But it has a maximum value. Push harder than that maximum and the object starts to slide. Then kinetic friction, also called sliding friction, takes over. Kinetic friction is usually smaller than the maximum static friction.

That is why a heavy fridge needs a big shove to get going, but less force to keep it moving. This guide explains both kinds, when friction helps, and how engineers reduce it.

What causes friction?

Even a surface that looks smooth is rough on a tiny scale. Under a microscope, polished metal looks like a range of hills and valleys. Two surfaces pressed together touch only at the tops of these bumps. The bumps catch on each other, and at the contact points the materials partly stick together.

To slide one surface over the other, these contacts must be broken or pushed past. The force that resists this is friction. Pressing the surfaces together harder makes more and larger contacts, so the friction increases. This is why a full suitcase is harder to drag than an empty one.

Friction between dry solids does not depend much on the area of contact or on the speed. Drag is different. It is the friction on anything travelling through air or water, and it grows with speed.

How does static friction match the push?

Imagine a student in Manchester trying to slide a heavy wooden chest across a classroom floor.

  • With no push, there is no friction. Nothing is trying to make the chest slide.
  • With a gentle push of 40 N, the chest stays still. The resultant force must be zero, so static friction is 40 N in the opposite direction.
  • With a harder push of 100 N, there is still no movement. Static friction has risen to 100 N.
  • At some push, static friction reaches its limit, say 120 N. Push a little harder than this and the chest starts to slide.

So the push sets the size of static friction, up to a maximum. This maximum is called limiting friction. It depends on the two surfaces and on how hard they are pressed together.

Worked example 1: does the chest move?

The chest has a mass of 25 kg. The largest static friction the floor can give is 120 N. Once the chest slides, kinetic friction is 90 N. The student pushes with 70 N, then with 130 N. Describe what happens each time, and find any acceleration.

Push of 70 N: this is less than 120 N, so the chest does not move. Static friction = 70 N, the resultant force is 0 and the acceleration is 0.

Push of 130 N: this is more than 120 N, so the chest starts to slide, and kinetic friction (90 N) now acts.

Resultant force: F=130−90=40 NF = 130 - 90 = 40\ \text{N}, in the direction of the push

Equation: a=Fma = \dfrac{F}{m}

Substitution: a=4025a = \dfrac{40}{25}

Answer: a = 1.6 m/s² in the direction of the push

If the push stays at 130 N, the chest keeps speeding up. To slide it at a steady speed, the student must reduce the push to 90 N.

Why is it harder to start something moving than to keep it moving?

When two surfaces rest together, the tiny bumps settle into each other and the contact points have time to grip. Once the surfaces are sliding, the bumps keep skipping past each other. They do not have time to settle and stick, so the grip is weaker.

So kinetic friction is usually smaller than the limit of static friction. You feel a jolt as a heavy box breaks free, and then it moves more easily. A squeaky door hinge and a violin bow on a string both stick and slip many times every second.

See this happen in the static and kinetic friction simulation. Press Pull and the friction arrow grows with the pull, then falls suddenly when the block slips. The friction graph shows a rise, a sudden drop, then a flat line.

Worked example 2: slowing to a stop

Later, the chest from Example 1 is sliding at 0.80 m/s. The student eases the push to 60 N. Kinetic friction is still 90 N. Find the deceleration and the time it takes to stop. What happens after it stops?

Resultant force: 90 − 60 = 30 N, backwards (against the motion)

Equation: a=Fma = \dfrac{F}{m}

Substitution: a=3025=1.2 m/s2a = \dfrac{30}{25} = 1.2\ \text{m/s}^2, backwards. This is a deceleration.

Time to stop: the speed falls by 1.2 m/s every second, so t=0.801.2=0.67 st = \dfrac{0.80}{1.2} = 0.67\ \text{s} (2 significant figures)

After it stops: friction is static again. The 60 N push is below the 120 N limit, so static friction is 60 N and the chest stays still. It does not slide back towards the student.

When is friction useful, and when is it a nuisance?

Daily life would be impossible without friction.

Useful friction:

  • Walking and running. Your foot pushes backwards on the ground, and friction from the ground pushes your foot forwards. On ice there is too little friction, so your foot slips back.
  • Driving. The tyres of a car or a rickshaw push back on the road, and friction pushes the vehicle forwards. The brakes then use friction to slow the wheels.
  • Grip. Rock climbers put chalk on their hands. Footballers wear studs. Towns in Canada and Norway spread grit on icy pavements.
  • Holding things together. Nails, screws and knots rely on friction.

Unwanted friction:

  • It heats moving parts. Energy is transferred to the thermal store of the parts and their surroundings, so less is left for the useful job.
  • It wears away brake pads, shoe soles, gears and tyres.
  • It makes engines and motors use more fuel or electricity for the same job.

How can friction be reduced?

  • Lubrication. Oil or grease puts a thin layer of liquid between the surfaces, so the bumps no longer rub directly. Car engines, bicycle chains and door hinges all need it. Polishing the surfaces also helps.
  • Rollers, wheels and ball bearings. Rolling causes far less friction than sliding. A heavy load on rollers or a trolley is much easier to move, and ball bearings let wheels and fans spin freely.
  • A cushion of air. A hovercraft rides on a layer of air, and so does the puck on an air-hockey table. The surfaces barely touch.
  • Streamlining, for drag. A smooth, pointed shape lets air or water flow past easily. High-speed trains in Japan and China have long, sloping noses. Racing cyclists crouch low, and swimmers wear smooth caps.

How do you show friction on a free-body diagram?

Draw friction as an arrow along the surface, pointing against the motion or the attempted motion. The normal contact force from the same surface is drawn at right angles to it. A box pushed along level ground has four forces: the push, friction, its weight and the normal contact force.

Build one in the free-body diagram simulation. The Pushing a crate situation starts with a 12 N push and 8 N of friction. Work out the resultant force, then press What next? to watch the crate speed up. Make the friction arrow as long as the push, and the resultant becomes zero: the crate stays at rest, or keeps a steady velocity if you give it a starting speed.

Common mistakes

  • Saying friction always equals its maximum. Static friction only matches the push, up to the limit.
  • Saying a still object has no friction on it. If something pushes it and it does not move, static friction is acting.
  • Using the starting push as the steady-speed push. Once sliding, a smaller push keeps a steady speed.
  • Thinking friction always points backwards. On a walker's shoe or a car's driving wheels, friction points forwards.
  • Leaving friction out of F = ma. Use the resultant force: the push minus the friction.
  • Mixing up friction and drag. Drag acts in liquids and gases and grows with speed. Sliding friction between solids stays about the same at different speeds.

Key points

  • Friction acts along touching surfaces and opposes sliding, or the tendency to slide.
  • Static friction matches the push exactly, up to a maximum called limiting friction.
  • Above that limit the object slides, and kinetic friction acts. It is usually smaller than the maximum static friction.
  • So it takes more force to start an object moving than to keep it moving at a steady speed.
  • Friction is useful for walking, driving, braking and grip, but it also heats and wears moving parts.
  • Lubrication, rollers, smooth surfaces and air cushions reduce friction. Streamlining reduces drag.