Skip to content

Forces simulation

Free-Body Diagram and Resultant Force Simulation

Build a free-body diagram by dragging force arrows and watch the resultant force appear, drawn to scale. See when forces balance, draw the tip-to-tail vector diagram and preview the motion that follows from a = F/m.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A puck on ice is pulled by 3 N towards the east and 4 N towards the north at the same time. How big is the resultant force?

Try this

  1. 1Choose Two forces at right angles. Predict the size of the resultant before you read it, then switch to the Vector diagram to see the triangle the two forces make.
  2. 2Choose Tug of war: unbalanced. Drag the tip of the right-hand arrow until the Balanced badge appears. How big is that force now, and why?
  3. 3Choose Pushing a crate and press What next? Then make the friction as big as the push, give the crate a starting speed and press What next? again. Compare the gaps between the faint copies.
  4. 4Choose Microlight plane in level flight and turn on Components of the resultant. Make the drag bigger than the thrust. Which way does the resultant point, and what does the plane do next?
  5. 5Choose Empty: add your own forces. Drag outwards from the crate to make two forces, press Balance, then check that the Vector diagram closes up.

What this simulation shows

An object sits in the middle of the picture: a crate, a box on a table, a rope, a plane, a skydiver or a puck on ice. Each arrow that starts at its centre is one force acting on it. Arrow length is proportional to force, and the grid behind the arrows sets the scale, printed in the top corner, for example "1 square = 5 N". Count squares along an arrow and you have measured that force, exactly as you would on a scale drawing.

You can have up to five forces. Drag the round handle at the tip of an arrow to change its size and direction, or drag outwards from the object to create a new force. Every drag has a slider, a number box and keyboard keys as an alternative, so you can also type exact values such as 233.1°.

How the resultant is found

The red striped arrow is the resultant force: the one force that would have the same effect as all of them together. The simulation finds it by adding the forces as vectors.

  • Forces along one line. Add those pointing one way and subtract those pointing the other way. A 12 N push against 8 N of friction leaves 4 N in the direction of the push.
  • Two forces at right angles. Drawn tip to tail they make a right-angled triangle, so Pythagoras gives the size, R=32+42=5 NR = \sqrt{3^2 + 4^2} = 5\ \text{N}, and trigonometry gives the direction, tan⁡θ=43\tan\theta = \tfrac{4}{3}, so θ=53.1∘\theta = 53.1^\circ.
  • Any set of forces. Each force is split into a horizontal part, Fcos⁡θF\cos\theta, and a vertical part, Fsin⁡θF\sin\theta. Adding all the horizontal parts gives ΣFx\Sigma F_x and adding all the vertical parts gives ΣFy\Sigma F_y. Pythagoras then combines the two totals. Turn on the components to see them as dashed arrows forming a right-angled triangle with the resultant.

Directions are measured anticlockwise from the direction pointing right, from 0° up to 360°. So 90° is straight up, 180° is to the left and 270° is straight down.

Balanced forces

When the resultant is zero, the green Balanced badge appears and the object glows. Zero here means zero to three significant figures, which is the precision every force is displayed to.

Balanced does not mean that nothing is happening. A box resting on a table and a plane cruising through the sky both have balanced forces on them. When the resultant force is zero the velocity cannot change, so a resting object remains at rest while a moving one keeps going with unchanged speed and direction. That idea is Newton's first law.

The vector diagram

Switch the view to the vector diagram to see the same forces drawn tip to tail. The first arrow starts at a point, and each new arrow begins where the previous one ended. The resultant joins the starting point to the final tip. If the forces balance, the final tip lands back on the start. Forces that do not all lie along one line then close into a triangle or another polygon. Scale-drawing questions use this method: you measure the closing side with a ruler and its angle with a protractor.

What happens next

Press What next? to let the forces act for three seconds. The simulation applies a=F/ma = F/m using the mass you choose, so the acceleration always points along the resultant. A faint copy of the object is left every half second. Equal gaps mean a constant velocity, while growing gaps show the object speeding up. Give it a starting speed to check that balanced forces keep a moving object moving.

The ready-made situations use round numbers to keep the arithmetic simple. Any weight is calculated from W=mgW = mg with the value of g used by your course.

Equations

  • Newton's second law

    F=ma

    resultant force = mass × acceleration

    Open calculator →
  • Resultant of two perpendicular vectors

    R=F12+F22

    (resultant)² = (first vector)² + (second vector)²

    Open calculator →

Check your understanding

8 questions

  1. 1.A box is pulled with 15 N to the right and 9 N to the left. What is the resultant force?
  2. 2.A parachutist falls at a steady speed. Which statement about the forces on the parachutist is correct?
  3. 3.Forces of 6 N and 8 N act at right angles on the same object. What is the size of the resultant force?
  4. 4.An object moving at 3 m/s has a resultant force of zero acting on it. What happens next?
  5. 5.A resultant force of 12 N acts on a trolley of mass 4 kg. What is its acceleration?
  6. 6.The force arrows in a tip-to-tail vector diagram join up into a closed shape. What does this show?
  7. 7.In this simulation directions are measured anticlockwise from the right. Which way does a force at 270° point?
  8. 8.A resultant force of 5.0 N acts at 53.1° anticlockwise from the right. What are its horizontal and vertical components?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more