What 4.6.1.3 covers
This is GCSE Physics only content (Combined Science leaves it out), for both tiers, with no equation.
- Where one material meets another, a wave may bounce back (reflection), carry on (transmission) or be taken in (absorption).
- Draw ray diagrams showing a wave bouncing off a surface, and describe what each outcome does in real situations.
- Required practical 9 (physics only) compares how surfaces reflect light and how substances refract it.
Refraction, including the Higher tier wavefront explanation, is in 4.6.2.2; measuring ripples is required practical 8 (4.6.1.2). Diffraction and interference are not in the AQA specification.
Three outcomes at a boundary
| Outcome | What the wave does | Example |
|---|---|---|
| Reflected | Turns back into the material it came from | An echo from a cliff |
| Transmitted | Continues into the new material | Daylight through a window |
| Absorbed | Hands its energy to the material, which warms slightly | Heavy curtains quietening a hall |
Often more than one happens: a shop window transmits most light, yet you glimpse your reflection in it. For electromagnetic waves, the outcome also depends on wavelength (Higher tier, 4.6.2.2).
Drawing a reflection ray diagram
- Rule a line for the reflecting surface.
- Where the ray strikes, draw the normal: dashed, at right angles to the surface.
- Add the incoming ray, arrow towards the surface. The angle of incidence, i, is between it and the normal.
- On the far side of the normal, add the reflected ray, arrow pointing away. The angle of reflection, r, equals i.
Law of reflection: i = r, both taken from the normal. A ray that travels along the normal goes straight back. Only the direction of travel changes: the wave is still in the same material, so its speed, wavelength and frequency stay the same.
Worked example: an angle given from the surface
A ray strikes a plane mirror, making 62° with its surface. Find the angle of reflection and the angle between the incoming and reflected rays.
Given: ray to surface = 62°
Step 1: the normal is at 90° to the mirror, so i = 90° − 62° = 28°.
Step 2: r = i = 28°.
Step 3: the rays lie on opposite sides of the normal, so the angle between them = 28° + 28° = 56°.
Answer: r = 28°, and the rays are 56° apart. The trap answer, 62°, is measured from the surface.
Smooth and rough surfaces (physics only, 4.6.2.6)
A mirror sends every ray of a parallel beam off in one direction: specular reflection, which forms a clear image. Paper has tiny bumps facing every way, so although each ray obeys i = r, the light scatters: diffuse reflection, with no image.
Required practical 9 (physics only)
Stand a plane mirror along a line on paper and draw a normal to it. Aim a narrow ray box beam at the point where the normal meets the mirror and mark the incoming and reflected beams with two crosses each. Remove the mirror, join the crosses and measure i and r with a protractor. Repeat at other angles. Then swap the mirror for white card, matt black paper and crumpled foil, and compare how bright and sharp the reflected beam looks. For the refraction half, try our glass block virtual lab.
Using the ripple tank simulation
In the simulation above, pick Reflection from the menu beside Play, then press Play. The cards read Angle of incidence (i) 40° and Angle of reflection (r) 40°, with Rays, normals and labels already on. Drag the Angle of incidence slider between 20° and 70°, then press Strobe to freeze the pattern: the reflected wavefronts leave at the matching angle, as far apart as the incoming ones. The gauze beaches absorb almost every ripple reaching them.
Press Strobe again to unfreeze, then pick Refraction, where the ripples carry on across a change of depth. Over the glass plate the ripples slow from 0.25 m/s to 0.15 m/s and their wavelength shrinks from 5.00 cm to 3.00 cm, while the frequency stays 5.0 Hz. With the Angle of incidence at the plate at 40°, their direction of travel turns towards the normal (explaining why is Higher tier). Gap, Edge and Two dippers go beyond AQA GCSE.