Spec point 4.7.2.3: Higher tier only
Motors appear on Higher tier papers only, for both GCSE Physics and Combined Science students. No new equation comes with them. The job is to show, step by step, why the forces on a coil's sides (found with Fleming's left-hand rule, 4.7.2.2) set it spinning.
The specification never names the split-ring commutator, yet a simple d.c. motor cannot keep turning without one, so learn its job. Physics-only students may also need to interpret diagrams of devices like this (4.7.2.1).
Parts of a simple d.c. motor
- a rectangular coil of insulated copper wire on an axle
- a magnet, so that a field crosses the coil from N to S
- a d.c. supply, joined to the coil through two carbon brushes
- a split ring: two copper half-rings on the axle, each joined to one end of the coil
Why the coil turns
The current flows out along one long side of the coil and back along the other. The two sides therefore carry current in opposite directions, and Fleming's rule gives them opposite forces: one up, one down. Those forces sit on opposite sides of the axle, so between them they rotate the coil.
As long as current flows, neither force changes size as the coil rotates. Their turning effect does change, because the lines of the forces move closer to the axle or further from it:
| Coil's plane | Turning effect | Why |
|---|---|---|
| Parallel to the field (flat) | Greatest | Each force acts at its largest distance from the axle. |
| Part-way round | Smaller | The forces act closer to the axle's line. |
| Perpendicular to the field (upright) | Zero | Both forces act straight through the axle. |
The job of the split ring
Reaching the upright position, the coil is still moving, so it swings a little way past. If nothing changed, the forces would then drag it back, and after rocking to and fro it would settle upright. The split ring prevents this. Just as the coil passes upright, each brush crosses a gap onto the other half-ring. The coil's connections swap, so its current reverses. The side that has just arrived on the right now gets the push its partner had there a moment before, and the coil keeps going round the same way.
Faster, or the other way
In exam answers, the coil spins faster with a bigger current, a stronger magnet or more turns of wire, since each makes the forces larger. (Real motors are more complicated: there, a stronger magnet or extra turns can even lower the top speed, for reasons beyond GCSE.) Swapping the supply connections or turning the magnet round reverses the spin; doing both leaves it unchanged.
Worked explanation: which way does it spin?
In a diagram, the field points from an N pole at the left to an S pole at the right. The coil lies flat. Current flows into the page along the coil's left-hand side and back out of the page along its right-hand side.
- Left-hand side: first finger right, second finger into the page, thumb down.
- Right-hand side: opposite current, so the thumb points up.
- Left side falling, right side rising: the coil turns anticlockwise in the diagram.
Running the motor on screen
In the simulation above, pick d.c. motor from Set-up. You get 20 turns, 0.5 T and 2 A with a Split ring. Each side of the coil has 0.05 m of wire in the field, so Force on each side shows N, and Turning effect now starts at its maximum, 0.04 N m, because the coil starts flat.
- Press Play. Viewed from the front the coil goes clockwise, and Speed (model) settles near 0.6 turns/s.
- Press Slow-mo and follow the brushes. Within 6° of upright they sit on the gaps: Current in side 1 reads none, Force on each side drops to 0 N and the moving dots of charge vanish. Past the gap, the current returns, reversed. Press Slow-mo again when you have seen it.
- The graph below the stage peaks with the coil flat and touches zero at each line marked vertical.
- Raise Current to 4 A (about 1.1 turns/s), then press Reverse I: the coil slows, stops and spins anticlockwise. Once in a while it stops upright with the brushes on the gaps instead. No current flows there, so no force can restart it: a real motor with a single coil can get stuck in this position too. Press Reset, then Play, to start again from flat.
- Select Slip rings, press Reset, then Play. With no current reversal the coil rocks and comes to rest upright.