What AQA asks for: spec point 4.5.3
This topic is on both tiers, in GCSE Physics and in Combined Science. You need to:
- give examples of forces that stretch, bend or compress an object, and explain why a stationary object needs more than one force to change shape
- describe the difference between elastic and inelastic deformation
- recall and use , which is not on the equation sheet, and calculate a spring constant from linear data
- tell a linear force–extension relationship from a non-linear one
- calculate the work done in stretching a spring with , which is given on the equation sheet
- describe Required practical 6, force and extension for a spring. Combined Science students do the same practical under a different number.
Changing shape needs two forces
Pull on a loose spring and it just moves the way you pull. To stretch a stationary spring, a second force must act the opposite way: a clamp pulls up on the top while the load pulls down. Two palms squeezing a tennis ball compress it, and a diver pushing down on the free end of a fixed board bends it.
Elastic or inelastic?
An object is elastically deformed if it returns to its original shape and length once the forces are removed. If it stays changed, it has been inelastically deformed. A car's suspension spring deforms elastically over every bump; a paper clip bent open deforms inelastically.
Force and extension
The extension is the increase in length: stretched length minus original length. Up to a point called the limit of proportionality, doubling the force on a spring doubles its extension, so the two are directly proportional:
is the force in newtons (N), the spring constant in newtons per metre (N/m) and the extension in metres (m). A stiffer spring has a larger . For a compressed spring, is the compression.
On a force–extension graph with force on the vertical axis, the linear part is a straight line through the origin with gradient . Past the limit of proportionality the line curves: the relationship is non-linear and no longer applies.
Worked example 1. A spring is 6.0 cm long with nothing on it. A 300 g mass stretches it to 13.0 cm. Take N/kg.
Given: N and cm m. Equation: , so . Substitution: . Answer: N/m.
Work done and elastic potential energy
Stretching or compressing a spring means doing work on it, and that energy goes into the spring's elastic potential energy store. As long as the deformation is elastic, all of the work done is stored. Up to the limit of proportionality:
Worked example 2. How much energy does the spring in example 1 store?
Given: N/m, m. Substitution: . Answer: J, or 0.10 J to 2 s.f. That equals the area under the force–extension line, .
Required practical 6
Clamp the spring to a stand with a metre rule upright beside it, its zero level with the top of the spring. Fix a pointer to the bottom of the spring and read the original length. Add slotted masses to a hanger one at a time. Each time, let it settle and read the pointer at eye level to avoid parallax. Find each weight with and each extension from the original length. Plot force against extension and use the gradient of the straight section to find .
Using the simulation
In the simulation above, the Soft spring starts unloaded, 5.00 cm long. Press Record first to log this original length. Then press Add to hang the 100 g hanger: Load shows 0.980 N and Extension 2.45 cm. Record, add another mass, and repeat. The Force–extension graph points form a straight line with gradient 40 N/m, as on the Spring constant card.
At 500 g the extension is 12.25 cm and Energy stored reads 0.300 J, matching . The sixth mass takes the spring past its limit of proportionality. Add a seventh, then press Remove until nothing is left: the spring stays 0.87 cm longer, because it has deformed inelastically. The simulation's messages use two names that the AQA specification does not use: Hooke's law for the straight-line behaviour, and elastic limit for the point where stretching becomes permanent. Swap in a new one resets it. The Rubber band is elastic but its graph is never a straight line.