Aim
To find out how the resistance of a metal wire depends on its length while its temperature stays steady, and to measure the resistance of one metre of that wire.
Equipment
- just over a metre of thin constantan wire, for example 0.38 mm across (about 28 swg)
- a metre rule, with the wire taped straight along it
- a low-voltage d.c. supply and a switch
- a digital ammeter and a digital voltmeter
- one clip fixed at the 0 cm mark and one crocodile clip that slides along the wire
- connecting leads
The circuit
The supply, the switch, the ammeter and the stretch of wire between the two clips make one series loop. The current is the same everywhere in a series loop, so the ammeter reads the current through the wire under test.
The voltmeter goes in parallel: one lead to the fixed clip, the other to the crocodile clip. It then reads the p.d. across the stretch being tested and nothing else. The circuit diagram in the lab above shows both meters in place.
Variables
| Type | Variable |
|---|---|
| Independent | Length of wire between the clips, read from the rule |
| Dependent | Resistance of that length, calculated from the two meter readings |
| Control | The same wire throughout (same metal, same diameter) and a steady temperature, kept by using a small current and switching off between readings |
Method
- Tape the wire tightly along the rule so that it has no kinks. Line the fixed clip up with the zero mark.
- Build the circuit. With the switch open, check that both meters read zero.
- Fix the crocodile clip at 20 cm. Close the switch, write down both readings straight away, then open the switch.
- Move the clip on in equal steps, every 10 cm or 20 cm, up to 100 cm. Take a pair of readings at each position.
- Go through every length twice more. Take the clip off and put it back on each time, so the repeats are independent.
- Work out the resistance for each pair of readings, then the mean at each length. Leave out any value that is clearly out of line with the others.
- Plot mean resistance on the vertical axis against length on the horizontal axis, and draw one straight line of best fit.
In the virtual version, each press of Take reading turns the supply on for three seconds while both meters are read, then turns it off, unless you choose to leave it on.
Risk assessment
| Hazard | Risk | Control |
|---|---|---|
| A short length carrying a large current gets hot | Burnt fingers | Use a low supply setting, avoid very short lengths, open the switch between readings and let the wire cool before touching it |
| Cut ends of thin wire | Scratches or a pricked finger | Fold the ends under the tape and handle the wire gently |
| Far too much current | The wire glows; meters or the supply are damaged | Start at the lowest setting and switch off at once if a meter goes off its range |
Analysing the results
Each pair of meter readings gives one resistance:
The points should lie close to one straight line through (0, 0), so resistance is directly proportional to length: twice the length, twice the resistance. The gradient gives the resistance of each metre of the wire, about 4.3 Ω per metre for 0.38 mm constantan in the lab's model. Plot length in metres to get the gradient in ohms per metre (with centimetres, multiply it by 100).
When the line misses the origin. A line that crosses the resistance axis a little above zero usually means every reading includes the same extra resistance, most often contact resistance where the clips grip the wire. Switch on Worn clips in the lab to see the whole line move up by about 0.3 Ω. A fixed clip that is not on the zero mark gives a zero error in every length, which slides the line sideways. Both are systematic errors that leave the gradient unchanged, so the gradient is the result to trust.
Uncertainty. Half the range of the repeats at one length is a simple estimate of its uncertainty. The lab also gives an uncertainty for the gradient, from the steepest and least steep lines that still pass through the error bars at the shortest and longest lengths.
Evaluation
Temperature. The current heats the wire, and a hotter metal has a higher resistance. Short lengths suffer most, because their small resistance lets a large current through. Schools often use constantan because its resistance hardly changes when it warms. In the lab, choose nichrome, 3 V and 10 cm, and turn off Switch off between readings: the readings come out more than 10% too high. Warm short lengths also lift one end of the graph, so the line misses the origin and its gradient is too small.
Length. A crocodile clip's jaws are a few millimetres wide, so each length is uncertain by a millimetre or two. That is a bigger share of 10 cm than of 100 cm. Look straight down at the scale to avoid parallax.
The meters. A small current such as 0.028 A has only two significant figures. A higher supply setting gives more precise readings but warms the wire more.
Anomalies. A reading well away from its repeats, often from a clip that did not bite properly, is left out of the mean and taken again. The lab shows such values in brackets.
Improvements. Take more lengths and repeats, keep the current small, clean the wire and the clips, and read the rule where the jaws touch the wire.
Part 2: resistors in series and in parallel
AQA's Required practical 3 also covers combinations of resistors. Put two resistors in place of the wire, keep the ammeter in series, and connect the voltmeter across both resistors together; then gives their combined resistance. Measure each resistor alone, then the pair in series, then in parallel. In series, the total is the sum of the two. In parallel, it is less than the smaller one, because the second branch gives the current another path. The lab above covers only the wire: try the combinations in the series and parallel circuits simulation.
Extension: a thinner wire
This part is for Cambridge students: the Core describes the effect of thickness in words and the Supplement calculates with it. AQA GCSE does not include it.
A wire of the same metal with half the diameter has a quarter of the cross-sectional area, because the area of a circle depends on its diameter squared:
Resistance varies inversely with the area of cross-section, so the thinner wire's line should be about four times as steep. Choose Constantan, 0.19 mm in the lab and compare the two gradients. Resistivity, which joins length and area in one equation, is in neither course.
In your exams
AQA GCSE Physics, section 4.2.1.3. This is Required practical activity 3, for both tiers (AQA Combined Science has it under another number). It covers how resistance depends on the length of a wire kept at a steady temperature, and the resistor combinations in Part 2. You must recall , and section 4.2.1.4 asks you to explain the design of a circuit that measures a resistance from a current and a p.d. Cross-sectional area and resistivity are not part of the AQA specification.
Cambridge IGCSE Physics 0625, section 4.2.4. In the Core (statements 1 to 3), you recall and use , describe how a voltmeter and an ammeter are used to find a resistance, and state in words how a wire's length and thickness affect its resistance. Supplement statement 5 adds calculations with and . The practical papers list the link between the p.d. across a wire and its length as one of their contexts, and treat two results within about 10% of each other as equal within the experiment's accuracy.
Exam-style questions
1. A student wants to measure the resistance of 40 cm of wire. Explain why the voltmeter should be joined to the two clips rather than to the terminals of the supply. (2 marks)
2. At a length of 30 cm, three values of resistance are 1.31 Ω, 1.29 Ω and 1.62 Ω. Identify the anomalous value and calculate the mean resistance. (2 marks)
3. A graph of resistance against length is a straight line with a gradient of 4.4 Ω/m. It crosses the resistance axis at 0.2 Ω. Suggest a cause of the intercept, and use the gradient to find the resistance of 0.65 m of the wire itself. (3 marks)
4. Explain why the student should open the switch after taking each pair of readings. (2 marks)
5. Cambridge Supplement. A second wire is made of the same metal but has twice the diameter. The first wire has a resistance of 4.4 Ω per metre. Calculate the resistance per metre of the second wire. (2 marks)