Skip to content

GCSE Physics — AQA · Forces

Upthrust and floating

4.5.5.1.2Higher tierPhysics only

Higher tier, GCSE Physics only. The bottom of an object in a liquid is deeper than its top, so it feels more pressure there, giving a resultant upward force: upthrust. An object floats when upthrust balances its weight and sinks when its weight is bigger.

Loading simulation…

Symbols match your course. Open the full upthrust and floating simulation for more presets and teacher tools.

Where this fits: Higher tier, physics only

Spec point 4.5.5.1.2 also covers upthrust and floating, which only Higher tier students of GCSE Physics are examined on. You need to:

  • explain upthrust using the difference in pressure between the bottom and the top of an object
  • describe what decides whether an object floats or sinks.

There is no upthrust equation to learn. Calculations combine p=hρgp = h\rho g, from the equation sheet, with p=FAp = \dfrac{F}{A}, which you recall, or simply subtract a newtonmeter reading from the weight.

Why a liquid pushes upwards

Pressure in a liquid increases with depth, and the bottom of an object is lower than its top, so the liquid presses harder on the bottom. Each push acts at right angles to its surface: up on the bottom, down on the top. The bigger upward push leaves a resultant force upwards: the upthrust.

The sides are pushed too, but each sideways push is matched by an equal one at the same depth on the opposite side, so they cancel. If only part of an object is under the surface, the liquid presses on its bottom but not on its top.

Worked example 1: a sensor in a lake. A sealed cylindrical sensor is 0.25 m tall, and each flat end has an area of 0.020 m². A tether holds it upright under a lake, with its upper end 0.75 m below the surface. What upthrust acts on it? (g = 9.8 N/kg; lake water 1000 kg/m³.)

Given: upper end at h=0.75h = 0.75 m, lower end at h=0.75+0.25=1.00h = 0.75 + 0.25 = 1.00 m, A=0.020A = 0.020 m². Equations: p=hρgp = h\rho g at each end, then F=pAF = pA for the difference. Substitution: upper end, p=0.75×1000×9.8=7350p = 0.75 \times 1000 \times 9.8 = 7350 Pa; lower end, p=1.00×1000×9.8=9800p = 1.00 \times 1000 \times 9.8 = 9800 Pa. The lower end has 2450 Pa more, so the upthrust =2450×0.020= 2450 \times 0.020. Answer: upthrust =49= 49 N, upwards.

Lower it further and the pressures at both ends grow equally, so the upthrust stays 49 N.

Floating and sinking

Two forces decide what happens: weight acts downwards and upthrust acts upwards.

Forces on the objectWhat happens
Weight bigger than the upthrust, even fully underResultant force downwards: it sinks to the bottom
Weight smaller than the upthrust when fully underResultant force upwards: it rises until part of it is above the surface
Upthrust equal to the weightBalanced forces: it floats at rest

These factors decide which row applies:

  • Density of the object compared with the liquid. A denser object sinks, because even fully under it gets less upthrust than its weight. A less dense object floats.
  • How deep it sits. A floating object sinks in until the pressure on its bottom gives an upthrust equal to its weight. Load it and it settles deeper.
  • Density of the liquid. In a denser liquid the pressure rises faster with depth, so an object needs to sink in less: it floats higher. A ship floats slightly higher in the sea than in a river.
  • Shape. Steel is about eight times as dense as water, yet steel ships float. A hollow hull encloses a lot of air, so the ship as a whole is less dense than water. Squashed into a solid lump, the same steel would sink.

Using the simulation

When the simulation above opens, a 100 cm³ aluminium block hangs from a newtonmeter over a eureka can of water, with the force arrows on. Weight in air reads 2.65 N. Press Lower, under the stage, four times; each press puts another quarter of the block under. The Upthrust card climbs 0.245 N at a time to 0.980 N, and the Newtonmeter reading falls to 1.67 N.

Switch on Pressure on the top and bottom faces, which starts off, then press Lower once more to take the block 2 cm deeper. The pressure due to the water is now 588 Pa on the bottom face and 196 Pa on the top, and the resultant upward force is 1.47 N − 0.490 N = 0.980 N: no extra upthrust.

Choose Float and press Drop in. The pine cube settles with 50% under the water, where upthrust = weight = 4.90 N. Select Glycerol, which is denser, and only 40% stays under. Then pick Nylon from the cube list, go back to Water and drop it in: its 11.3 N weight beats the 9.80 N upthrust, so it sinks.

Common mistakes

  • Writing only that "the water pushes up". Explain where the force comes from: the bottom surface is deeper than the top, so the pressure and the force on it are bigger.
  • Thinking a fully submerged object gets more upthrust the deeper it goes. The top and bottom pressures increase equally, so their difference, and the upthrust, stay the same.
  • Saying that a floating object has more upthrust than weight. When it floats at rest the forces are balanced: upthrust = weight.
  • Saying heavy objects sink and light ones float. A huge steel ship floats, so compare the object's density with the liquid's, or its weight with the upthrust.
  • Adding the sideways pushes to the upthrust. They act horizontally in equal and opposite pairs, so they cancel.
  • Using a depth in cm, or an area in cm², when turning pressures into forces. Convert to m and m² before using p = hρg and F = pA.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.Higher tier, physics only. A concrete block is held completely under fresh water by a cable. Its top and bottom faces each measure 0.50 m by 0.40 m, and the block is 0.30 m tall. Its top face is 0.10 m below the surface. Use g = 9.8 N/kg. The water's density is 1000 kg/m³.

    1. (a)Calculate the pressure due to the water on the top face of the block.

      2 marks
      Show the answer

      Answer: p = hρg = 0.10 × 1000 × 9.8 = 980 Pa

      Marking points

      • p = 0.10 × 1000 × 9.8
      • 980 Pa
    2. (b)Calculate the force that this pressure exerts on the top face.

      2 marks
      Show the answer

      Answer: Area = 0.50 × 0.40 = 0.20 m². F = pA = 980 × 0.20 = 196 N, downwards.

      Marking points

      • Area of the face = 0.20 m².
      • F = 980 × 0.20 = 196 N (allow their pressure).
    3. (c)Calculate the upthrust on the block.

      3 marks
      Show the answer

      Answer: The bottom face is 0.10 + 0.30 = 0.40 m deep, so p = 0.40 × 1000 × 9.8 = 3920 Pa. Force on the bottom = 3920 × 0.20 = 784 N, upwards. Upthrust = 784 − 196 = 588 N.

      Marking points

      • Depth of the bottom face = 0.40 m, so its pressure = 3920 Pa.
      • Force on the bottom face = 3920 × 0.20 = 784 N.
      • Upthrust = 784 − 196 = 588 N (allow their values).
    4. (d)Explain why the forces of the water on the sides of the block do not add to the upthrust.

      2 marks
      Show the answer

      Answer: Each side face has a matching face opposite it at the same depths, so the two forces have the same size but act in opposite directions. These horizontal forces cancel, so they give no resultant force.

      Marking points

      • Forces on opposite sides match in size but point in opposite directions (they are at the same depths).
      • So they cancel: they are horizontal and give no upward resultant.
  2. 2.Higher tier, physics only. A solid steel bolt sinks when it is dropped into a harbour. A cargo ship, made mostly of steel, floats in the same water.

    1. (a)Explain why the bolt sinks.

      2 marks
      Show the answer

      Answer: The bolt's weight is greater than the upthrust on it, even when it is completely under, because steel is denser than water. So the resultant force on it is downwards.

      Marking points

      • The weight of the bolt is greater than the upthrust on it (even when fully submerged).
      • Steel is denser than water, so the resultant force on the bolt is downwards.
    2. (b)Explain why the ship floats.

      4 marks
      Show the answer

      Answer: The hull is hollow and contains air, so the ship as a whole is less dense than water. As the ship settles into the water, its bottom gets deeper, so the pressure on the bottom, and the upthrust, increase. It stops sinking in when the upthrust equals its weight. The forces are then balanced, so it floats.

      Marking points

      • The hull is hollow and holds air, so the ship's overall density is lower than water's.
      • The deeper the bottom of the hull, the greater the pressure on it.
      • So the upthrust increases as the ship settles lower.
      • It floats where the upthrust equals its weight (balanced forces).
    3. (c)Cargo is loaded onto the ship. Explain what happens to how low the ship sits in the water.

      2 marks
      Show the answer

      Answer: Its weight increases, so it sinks lower. The bottom of the hull is then deeper, so the pressure on it and the upthrust are bigger, until the upthrust equals the new weight.

      Marking points

      • The ship sits lower in the water, because its weight has increased.
      • The deeper hull bottom has a greater pressure on it, so the upthrust grows until it equals the new weight.
  3. 3.Higher tier, physics only. A rectangular pontoon of mass 1500 kg floats on the sea in a harbour. Its flat base has an area of 6.0 m², and its sides are vertical. g = 9.8 N/kg, and the harbour's sea water has a density of 1030 kg/m³.

    1. (a)Determine the size of the upthrust on the pontoon. Give a reason for your answer.

      2 marks
      Show the answer

      Answer: 14 700 N. The pontoon floats at rest, so the upthrust balances its weight: W = mg = 1500 × 9.8 = 14 700 N.

      Marking points

      • 14 700 N (= mg = 1500 × 9.8).
      • It floats at rest, so upthrust = weight (the forces are balanced).
    2. (b)Calculate the pressure due to the sea water on the base of the pontoon.

      2 marks
      Show the answer

      Answer: p = F ÷ A = 14 700 ÷ 6.0 = 2450 Pa

      Marking points

      • p = 14 700 ÷ 6.0 (allow their upthrust)
      • 2450 Pa
    3. (c)Calculate how far the base of the pontoon is below the surface.

      3 marks
      Show the answer

      Answer: h = p ÷ (ρg) = 2450 ÷ (1030 × 9.8) = 0.24 m

      Marking points

      • h = p ÷ (ρ × g)
      • 2450 ÷ (1030 × 9.8)
      • 0.24 m (accept 0.243 m).
    4. (d)The pontoon is towed up a river into fresh water, density 1000 kg/m³. Explain whether it floats higher or lower than it did in the sea.

      2 marks
      Show the answer

      Answer: Lower. The upthrust must still equal the same weight, so the pressure on the base must still be 2450 Pa. Fresh water is less dense, so a greater depth (0.25 m) is needed to give that pressure.

      Marking points

      • It floats lower (its base is deeper, at 0.25 m).
      • The same upthrust, and so the same pressure, is needed, but fresh water is less dense, so a greater depth is needed.
  4. 4.Higher tier, physics only. A student hangs a stone from a newtonmeter. The newtonmeter reads 3.6 N with the stone in air, and 2.2 N with the stone completely under water.

    1. (a)Calculate the upthrust on the stone in the water.

      1 mark
      Show the answer

      Answer: Upthrust = 3.6 − 2.2 = 1.4 N

      Marking points

      • 1.4 N
    2. (b)Explain why there is an upthrust on the stone.

      2 marks
      Show the answer

      Answer: The bottom of the stone is deeper than its top, so the water pressure on the bottom is greater. The upward force on the bottom is therefore bigger than the downward force on the top, leaving a resultant force upwards.

      Marking points

      • The bottom of the stone is deeper, so the pressure on it is greater.
      • So the upward force on the bottom is bigger than the downward force on the top, giving a resultant upward force.
    3. (c)The student lowers the stone further, keeping it completely under the water and off the bottom. State and explain what happens to the newtonmeter reading.

      3 marks
      Show the answer

      Answer: It stays at 2.2 N. The pressures on the top and on the bottom both increase by the same amount, so the difference between them does not change, and the upthrust stays 1.4 N.

      Marking points

      • The reading stays the same (2.2 N).
      • The pressures on the top and bottom increase by the same amount.
      • So the pressure difference, and the upthrust, do not change.
    4. (d)The stone is then hung completely under salty water, which is denser than fresh water. Predict how the reading compares with 2.2 N. Give a reason.

      2 marks
      Show the answer

      Answer: It is less than 2.2 N. In a denser liquid the pressure increases more with depth, so the pressure difference between the bottom and top of the stone, and so the upthrust, are bigger.

      Marking points

      • The reading is lower than 2.2 N.
      • The denser liquid gives a bigger pressure difference, so a bigger upthrust.

Quick check

6 questions

  1. 1.What causes the upthrust on an object under water?
  2. 2.A boat floats at rest on a lake. Which statement is correct?
  3. 3.The water pressure on the bottom face of a submerged block is 2500 Pa greater than on its top face. Each face has an area of 0.040 m². What is the upthrust?
  4. 4.A diver holds a sealed metal can completely under water, then takes it down a further 3 m. What happens to the upthrust on the can?
  5. 5.Which of these solid cubes would sink in fresh water (density 1000 kg/m³)?
  6. 6.An egg sinks in fresh water but floats in very salty water. Why?