What spec point 4.5.6.2.2 covers
On both tiers you need the proportionality statements, the equation, estimates of forces in road transport, and Required practical 7. Inertial mass is Higher tier only.
is not on the equation sheet, so you must remember it: resultant force in N, mass in kg, acceleration in m/s².
How force, mass and acceleration are linked
- Keep the mass the same, and the acceleration is directly proportional to the resultant force: . Twice the force gives twice the acceleration.
- Keep the resultant force the same, and the acceleration is inversely proportional to the mass: . Twice the mass gives half the acceleration.
Together these give . So 1 N is the resultant force needed to accelerate 1 kg at 1 m/s². Always use the resultant force, never just the biggest force in the question.
Worked example 1: an e-scooter. A rider and scooter have a total mass of 90 kg. The motor gives a forward force of 150 N and resistive forces total 42 N.
Given: N forwards, kg. Equation: , so . Substitution: . Answer: m/s² forwards.
Higher tier: inertial mass
Inertial mass tells you how hard it is to change an object's velocity. It is defined as the ratio of resultant force to acceleration, . A full supermarket trolley has more inertial mass than an empty one, so the same push changes its velocity less.
Worked example 2. A resultant force of 36 N gives a loaded sledge an acceleration of 0.45 m/s². Equation: . Substitution: . Answer: inertial mass kg.
Estimating forces on the road
AQA expects sensible estimates. It uses the symbol to mark an approximate value; ≈ means the same and is used below. A family car has a mass of about 1500 kg. In an emergency stop from 20 m/s it might take about 3 s to stop, so m/s². The braking force is then N. A crash can stop a car in about a tenth of a second, so the forces are far larger and can cause serious injuries.
Required practical 7
Aim: find how a trolley's acceleration depends on the force (with mass fixed) and on the mass (with force fixed).
Typical set-up: a trolley on a level bench, a string tied to it running over a pulley at the bench edge, and a hanger with slotted masses on the other end. The weight of the hanging masses provides the pull. Measure the acceleration using light gates and a card fixed to the trolley, or by timing the trolley over marked distances.
Part 1, changing the force: start with several 100 g masses on the trolley. Move them to the hanger one at a time. The pull rises, but the total mass being accelerated (trolley plus hanging masses) stays the same, so it is a fair test.
Part 2, changing the mass: keep the hanging mass fixed and add masses to the trolley. Here is the total mass being accelerated, including the hanger.
Results: a graph of against is a straight line through the origin, showing . A graph of against is also a straight line through the origin, showing .
Errors and safety: friction shifts the – line along the force axis, so it misses the origin; tilting the runway slightly so the trolley rolls at a steady speed cancels it. Repeat each run and take a mean. Put a box of soft material under the hanger, and stop the trolley before it leaves the bench.
Using the simulation
In the simulation above, the starting set-up is 100 g hanging, 0.9 kg trolley. Press Play. The pull is the hanger's weight, 0.98 N, acting on 1.0 kg in total, so the acceleration readout shows 0.980 m/s². The velocity–time graph opens with its Gradient (tangent) tool on: drag along the line and compare its gradient with that value and the light-gate result.
Once the card has passed gate 2, press Record beside Play. Next, use Move 100 g to the hanger, run the trolley once more and record that too. Do this a few times. The results graph is already set to a against F, and the points line up through the origin.
Finally, compare 1.0 N pull, empty 0.5 kg trolley with 1.0 N pull, 1.0 kg trolley. Doubling the mass halves the acceleration, from 2.0 m/s² to 1.0 m/s².